Summary
Ideal is one of the three biggest-selling boiler brands in the UK, and the Logic combi in particular is everywhere in the social-housing and landlord market. That means its codes are the ones a heating engineer sees most often — and the ones most often mis-read, because Ideal has used the same letters with different meanings across its ranges. On a Logic, L2 is an ignition lockout; on an older Isar, L2 is also an ignition lockout but F2 is a flame-loss fault with a different reset behaviour; on the Logic Combi2 and Vogue Max the display adds a description so the ambiguity goes away. The first job on any Ideal callout is to identify the model and generation from the data badge (inside the drop-down panel on a Logic) before you act on the code.
The code structure on current models is logical once you know it. L codes are lockouts: the boiler has detected a condition it will not recover from on its own and needs the reset button pressed. F codes are faults: some clear themselves when the condition resolves (F1 low pressure clears when you repressurise; F7 low mains clears when the voltage recovers), others require a reset after the underlying fault is fixed. C codes are configuration faults on the PCB. Knowing which family you are looking at tells you whether the customer's "it keeps doing it" is a recurring hard fault or a self-clearing one with an upstream cause.
This guide tabulates the current Logic/Vogue code set, flags where the older ranges differ, gives the diagnostic path for the five codes that make up most callouts, and gives decision trees for ignition lockout and low pressure. Codes marked **** are documented on third-party sources but should be checked against the model's installation and servicing manual before a part is ordered.
Key Facts
- Current ranges (Logic, Logic+, Logic Max, Logic Combi2, Vogue, Vogue Max, Independent, Independent Max): L = lockout (manual reset), F = fault, C = configuration
- Older ranges (Isar HE, Icos HE, Esprit, Classic, Mini, Response): mostly L and F codes with partially different meanings; Isar/Icos also show LC, LF and a flashing green LED pattern on models without a digital display
- Two most common codes: F1 (low water pressure, below ~0.5 bar — self-clearing once repressurised to 1–1.5 bar cold) and L2 (ignition lockout after failed ignition attempts — manual reset)
- F2 = flame loss during operation (as opposed to failure to light); recurrent F2 points to gas supply pressure, flue recirculation or electrode/ionisation faults
- L1 = flow thermistor overheat or no circulation — the boiler saw a flow temperature above its limit (typically ~95–100 °C) or a rise rate indicating no flow; do not reset repeatedly
- F3 = fan fault (no tacho signal or wrong speed); F4 = flow thermistor fault; F5 = return thermistor fault; F6 = outside sensor fault (only where an outdoor sensor is fitted); F7 = low mains voltage (below ~190 V); F9 = PCB/connection fault (often a loose or damp wiring plug after a service)
- FD = no water flow detected / dry-fire protection on some Logic models — frequently an airlocked or sludged circuit
- L5 = PCB or flow thermistor fault after five L1 lockouts in a row; L6 = false flame detected (flame sensed with gas valve closed) — gas safety related; L9 = PCB fault
- C0 / C2 = PCB configuration fault (wrong or missing configuration after a PCB swap)
- LA / LC / LF on Isar/Icos: LA = flow thermistor; LC = five resets within 15 minutes (lock-out of the reset); LF = ignition lockout
- Reset: press the "restart"/reset button once for 1–3 seconds; on a Logic the display returns to the status indicator. Up to five resets in 15 minutes then the boiler blocks further resets (LC on older models) — wait and investigate rather than power-cycling
- Frozen condensate is the single biggest cause of L2 in winter on Ideal combis with an external condensate run; Ideal condensate pipes should be 32 mm externally and insulated (see condensate pipe installation)
- Ideal's own troubleshooting pages for Logic combi and system boilers give the official homeowner-level meanings; the installation and servicing manual gives the engineer-level fault table
- Gas Safety (Installation and Use) Regulations 1998 — all work behind the case is for a Gas Safe registered engineer; Benchmark commissioning record should be checked first on any callout
- Parts pricing (indicative, excluding labour): pressure sensor/switch £25–£60; flow or return thermistor £15–£30; ignition electrode and lead £25–£50; fan £120–£220; gas valve £120–£200; PCB £180–£300; diverter valve £90–£180; plate heat exchanger £120–£250 ****
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Code | Range | Meaning | Most likely causes | Reset type | Urgency |
|---|---|---|---|---|---|
| F1 | Logic/Vogue/Independent | Low system water pressure | Leak, PRV discharge, radiator bleed, expansion vessel | Self-clears when repressurised | Medium |
| F2 | Logic/Vogue | Flame loss during operation | Low gas pressure, flue recirculation, electrode/ionisation, gas valve | Automatic retry then lockout | High |
| F3 | Logic/Vogue | Fan fault | Fan tacho/wiring, fan seized, PCB | Manual after fix | High |
| F4 | Logic/Vogue | Flow thermistor fault | Open/short circuit thermistor, wiring | Manual after fix | Medium |
| F5 | Logic/Vogue | Return thermistor fault | Open/short circuit thermistor, wiring | Manual after fix | Medium |
| F6 | Logic/Vogue | Outside sensor fault | Sensor or wiring (only if fitted) | Clears when fixed | Low |
| F7 | Logic/Vogue | Low mains voltage | Supply below threshold, poor connection, shared circuit | Self-clears when voltage recovers | Medium |
| F9 | Logic/Vogue | PCB / unknown connection fault | Loose plug, damp PCB, PCB failure | Manual | Medium–High |
| FD | Logic (some) | No water flow / dry fire | Airlock, blocked heat exchanger, pump | Manual | High |
| FL / LF | Logic (display variant) / Isar | Ignition lockout | As L2 | Manual | High |
| L1 | Logic/Vogue | Flow overheat / no circulation | Pump failure, blockage, air lock, closed valves | Manual — investigate first | High |
| L2 | Logic/Vogue/Isar | Ignition lockout | No gas, frozen condensate, electrode, gas valve, low gas pressure | Manual | High |
| L5 | Logic | Repeated L1 / thermistor-PCB fault | As L1 plus thermistor/PCB | Manual | High |
| L6 | Logic/Vogue | False flame | Electrode/ionisation, leaking gas valve, PCB | Manual | High — gas safety |
| L9 | Logic/Vogue | PCB fault | PCB | Manual | High |
| C0 / C2 | Logic/Vogue | PCB configuration | Unconfigured replacement PCB | Service mode | Medium |
| LA | Isar/Icos | Flow thermistor fault | Thermistor, wiring | Manual | Medium |
| LC | Isar/Icos | Five resets in 15 minutes | Underlying recurring fault | Wait 15 min then reset | — |
| Any code not listed | Any | Unconfirmed for this model | **** | — | — |
Detailed Guidance
What does L2 mean on an Ideal boiler?
L2 — Ignition lockout. The boiler has attempted ignition (typically three or five attempts, depending on the model) without establishing a flame and has locked out. This is the Ideal code most often seen in January.
Causes, in rough order of frequency:
- No gas — pre-payment meter out of credit, meter valve or appliance isolation valve closed, other appliances also dead.
- Frozen condensate pipe — the Logic's condensate trap backs up and the pressure switch or flue sensing stops ignition. Look for an external run, especially a 21.5 mm pipe or a long uninsulated run to a drain. Thaw with warm (not boiling) water; then fix the run (see condensate pipe frozen boiler lockout).
- Ignition electrode / lead — worn or cracked electrode, carbon on the tip, wrong gap, HT lead tracking. The Logic electrode is a common service item.
- Low gas pressure — inlet working pressure at the boiler test point below ~17 mbar natural gas; check at the meter and boiler under load.
- Gas valve — coil or regulator fault; no click on ignition attempt.
- Flue — blocked terminal or recirculation (products of combustion drawn back in); check terminal and seals.
- PCB — no spark and no gas valve operation with everything else proven.
Diagnostic path: confirm gas at other appliances → check condensate pipe → reset once and watch the ignition sequence (fan runs, spark heard, gas valve clicks?) → no spark: electrode, lead, PCB → spark but no light: gas pressure, gas valve, flue → lights then L2 again: see F2 (flame loss).
What does F1 mean on an Ideal boiler?
F1 — Low water pressure. The pressure sensor reads below the minimum (around 0.5 bar). The display shows F1; on a Logic the status LED may flash. This is the only Ideal code a homeowner should ever fix themselves, and the one worth talking a tenant through on the phone.
Causes: system leak (radiator valve, pipe joint, automatic air vent), PRV lifting (look for a wet discharge pipe outside — expansion vessel usually the root cause), radiators bled without repressurising, expansion vessel lost charge or failed diaphragm, pressure sensor fault.
Path: read the gauge → repressurise via the filling loop to 1–1.5 bar cold → code clears → monitor through a heating cycle (0.3–0.5 bar rise is normal; more suggests expansion vessel) → if it drops again over days, systematic leak check (see boiler loses pressure repeatedly and boiler pressure relief valve discharging). If the gauge reads correctly but F1 persists, suspect the pressure sensor or its wiring.
What does L1 mean on an Ideal boiler?
L1 — Flow temperature overheat or no circulation. The flow thermistor saw a temperature above the limit, or a rate of rise that indicates water is not moving through the heat exchanger. On the Logic range this is the code that most often gets reset again and again by a customer until something expensive fails.
Causes: pump not running or seized (listen; check the pump plug), pump running but heat exchanger or system blocked with sludge/scale, air lock, all radiators closed on TRVs with no bypass, diverter valve stuck between positions, flow thermistor reading high (less common).
Path: let it cool → confirm pump runs on demand → check radiators warm/flow through system → check ΔT across the boiler (a very high ΔT with the pump running = restricted flow through the heat exchanger) → check automatic bypass and TRV settings → resistance-check the flow thermistor. Do not return the boiler to service on repeated resets; see boiler kettling for the scale/sludge route and powerflush.
What does F2 mean on an Ideal boiler?
F2 — Flame loss. The boiler lit, ran, and the flame signal was lost. It will usually retry automatically; repeated F2 becomes an L2 lockout. Unlike L2 the burner did light, which rules out most ignition-chain faults and points at gas supply under load, flue recirculation, ionisation/electrode or the gas valve modulating badly.
Path: check working gas pressure at the boiler with other appliances running (a drop under load points to pipe sizing or meter regulator — see gas pipe sizing) → check flue terminal position and seals for recirculation, especially with wind → inspect electrode and lead → combustion check with a flue gas analyser (see flue gas analysis) → gas valve.
What does F3 mean on an Ideal boiler?
F3 — Fan fault. The PCB is not seeing the expected fan speed signal. Causes: fan tacho lead or plug loose, fan motor failing (noisy before it fails — see boiler fan noise diagnosis), blocked flue causing the fan to over-speed or stall, PCB. Reset once; if the fan does not run on the pre-purge, check supply to the fan before condemning it.
F4, F5, F6, F7, F9 — sensors, mains and connections
- F4 / F5 — flow and return thermistors open or short circuit. Resistance-check against the manual's NTC table (typically ~10 kΩ at 25 °C). Check the plug and the pocket; a thermistor out of its pocket reads air temperature and causes erratic control before it fails.
- F6 — outside sensor fault, only on systems with an outdoor sensor fitted for weather compensation. Check wiring; the boiler will usually run on a default curve.
- F7 — mains voltage below the PCB's threshold. Measure at the boiler terminals under load; check the fused spur, the plug (if fitted), the earth, and whether the boiler shares a circuit with heavy loads. A failing PCB can also report F7.
- F9 — unknown or connection fault. Usually a plug not fully home after a service, a damp PCB (check for leaks onto it — the Logic's PCB sits below the hydraulics), or a failing PCB. Check connections before quoting a board.
L6 — false flame
The ionisation circuit reports a flame when the gas valve is closed. Causes: electrode or lead shorting to earth, moisture or carbon tracking, a leaking gas valve (genuinely dangerous), PCB fault. Treat as a gas safety matter: check for gas passing at the valve outlet with the valve de-energised before anything else.
Older Isar / Icos / Esprit models
The Isar HE and Icos HE (2000s) show codes on a small display and also flash the green/red LED. Common codes: L1 overheat, L2 ignition lockout, F1 low pressure, F2 flame loss, F3 fan, F4/F5 thermistors, LA flow thermistor, LC too many resets, LF ignition lockout. These boilers are now 15–20 years old; sludge, heat exchanger leaks and PCB failures dominate, and parts availability should be checked before quoting a repair against replacement.
Decision tree — L2 ignition lockout
L2 displayed
|
Gas at other appliances?
|
+---+-----------+
| |
No Yes
| |
Restore Condensate pipe frozen / blocked?
supply, |
reset +---+------+
| |
Yes No
| |
Thaw, reset, Reset once; watch sequence
re-route/ |
insulate +---+----------------+
| |
Fan runs, no spark Spark, no flame
| |
Electrode, lead, Gas pressure at
PCB test point under
load; gas valve
click; flue
terminal
Decision tree — F1 low pressure
F1 displayed
|
Gauge reading?
|
+---+----------------+
| |
Below 0.5 bar Normal (1-1.5 bar)
| |
Repressurise Pressure sensor /
to 1-1.5 bar wiring fault
cold, F1 clears
|
Monitor one heating cycle
|
+---+---------------+
| |
Holds Drops again (hours/days)
| |
Done; PRV discharging? -> expansion vessel
advise Not discharging -> systematic
leak check (valves, joints, AAV,
plate exchanger, under floors)
Frequently Asked Questions
How do I reset an Ideal Logic boiler?
Press the reset/restart button (marked with a circular arrow on the Logic fascia) once and hold for a second or two; the display changes from the fault code back to the status display and the boiler attempts to restart. If the same code returns straight away there is an active fault. After five resets in a short period the boiler will refuse further resets for a while — do not power-cycle at the spur to get round it, because you are masking a fault that may be a gas-safety one (L6) or one that damages the heat exchanger (L1).
Why does my Ideal boiler show F1 every few weeks?
Because water is leaving the system somewhere. Repressurising is not a fix, it is a reset. The usual culprits are a weeping radiator valve or tail, an automatic air vent dribbling, a PRV lifting because the expansion vessel has lost its charge, or — the one that is missed — a pin-hole in the plate heat exchanger or main heat exchanger where the loss goes down the condensate drain unseen. Monitor the pressure cold with everything off, then systematically check (see boiler loses pressure repeatedly).
Is L2 the same thing as F2?
No. L2 is a lockout after the boiler failed to light — the ignition chain or gas supply at start-up. F2 is flame loss after the boiler was running — gas pressure under load, flue, electrode or gas valve. The distinction tells you where to look: an L2 with no spark is electrode/PCB; an F2 on a windy day is often flue recirculation; an F2 whenever the cooker is on is gas pipe sizing.
My Ideal shows a code that is not in this list — what now?
Identify the exact model and year from the data badge inside the drop-down panel and open that model's installation and servicing manual (Ideal publish them on their website). Ideal has reused letters across ranges and the Vogue Max / Logic Combi2 add text descriptions that older models lack. Never order a part on the strength of a code alone.
How much does a typical Ideal repair cost?
Indicative, excluding labour: pressure sensor £25–£60; thermistor £15–£30; electrode and lead £25–£50; fan £120–£220; gas valve £120–£200; PCB £180–£300; diverter valve £90–£180; plate heat exchanger £120–£250. Labour typically £80–£150 for diagnosis plus the repair time. **** On a Logic over ten years old with a leaking main heat exchanger, compare against replacement before quoting.
Regulations & Standards
Gas Safety (Installation and Use) Regulations 1998 — all work on gas appliances, including fault diagnosis behind the case, must be carried out by a Gas Safe registered engineer
Building Regulations Approved Document J (England) — combustion appliances and fuel storage; flue and condensate requirements
Building Regulations Approved Document L (England) and Boiler Plus (2018) — controls and efficiency on replacement
BS 6798:2014 — installation and maintenance of gas-fired boilers up to 70 kW net input
BS 5440-1:2008 and BS 5440-2:2023 — flueing and ventilation of gas appliances
BS 7593:2019 — treatment of water in domestic hot water central heating systems (sludge-related L1/FD faults)
BS 7671:2018+A4:2026 — electrical work associated with the boiler supply (F7 investigation, PCB replacement)
BS 7967:2015 — carbon monoxide in dwellings and the combustion performance of gas appliances; flue gas analysis
Benchmark Commissioning Checklist — should be completed and reviewed on any callout
Ideal Heating — Logic Combi troubleshooting guide — manufacturer's own fault code meanings for the Logic combi
Ideal Heating — Logic System troubleshooting manual — manufacturer fault codes for the Logic system boiler
Gas Safe Register — statutory register for gas engineers in Great Britain
HSE — Gas Safety — statutory guidance on gas appliance safety
HomeServe — Ideal boiler fault codes — independent code summary
Heatable — Ideal boiler troubleshooting — independent code summary and repair cost ranges
boiler error codes vokera — comparable fault categories on another brand
boiler error codes worcester bosch — Worcester Bosch code families
boiler error codes vaillant — Vaillant F-codes
boiler error codes baxi — Baxi E-codes
condensate pipe frozen boiler lockout — the winter L2 cause
boiler loses pressure repeatedly — recurring F1
boiler pressure relief valve discharging — PRV and expansion vessel faults
boiler fan noise diagnosis — fan faults before F3
no hot water but heating works — diverter valve faults on the Logic combi
flue gas analysis — combustion checks after any gas-side repair