Summary
The customer's description is "the boiler sounds like a jet engine" or "it's making a grinding noise and then cutting out", and the engineer's job is to decide in ten minutes whether the fan is the fault, a symptom of a flue problem, or an innocent bystander while the pump or the heat exchanger makes the noise. The fan is a brushless motor driving a centrifugal impeller, either pushing air into a premix burner (modern condensing boilers, where the fan speed sets the gas rate through a venturi or a gas valve with a pneumatic link) or pulling products of combustion through a heat exchanger and out of the flue (older non-condensing fan-flued boilers, where an air pressure switch proves the fan before the gas valve opens). In both, the fan is proven — by a tacho signal or by the pressure switch — before gas is released, which is why a fan fault stops the boiler rather than letting it run dangerously.
This guide gives the noises and what they mean, the order of tests from the outside in, the differences between premix and pressure-switch boilers, the flue faults that masquerade as fan faults, what a replacement involves and costs, and the safety points. It does not give brand fault codes: see the brand error-code articles for those. For the neighbouring faults see boiler short cycling diagnosis and boiler not firing.
Key Facts
- What the fan does — pre-purge (typically 5–30 seconds of fan before ignition to clear the combustion chamber), proving (tacho feedback on premix fans, or an air pressure switch on older fan-flued boilers), combustion air supply during the burn, post-purge after the flame goes out
- Premix condensing boilers — fan speed is controlled by the PCB (PWM or a variable DC signal) and sets the firing rate; the gas valve follows the air flow. The fan reports speed back by a Hall-effect tacho; wrong speed or no signal = ignition lockout with a fan fault code
- Older fan-flued boilers — a single-speed 230 V fan; an air pressure switch (APS) with two silicone tubes to the fan housing or flue proves the fan is moving air before the PCB opens the gas valve. A failed APS, a split or blocked tube, or a weak fan that does not make the switch all give the same "fan runs but no ignition" fault
- Noises and meanings — whine, grind or scream that rises and falls with fan speed = bearings; rattle or buzz = loose housing, fixing or impeller debris; whistle or howl = flue or air-inlet restriction, a partially blocked terminal, a wrong-size or kinked flue, or ice; humming without rotation = seized rotor or a failed winding; clicking = relay or ignition, not the fan
- Fan does not run — check in order: boiler has a demand (controls, pressure, overheat stat), fan supply present at the fan plug (230 V on older fans, 24–40 V DC plus a PWM signal on premix fans, per the manufacturer's wiring diagram), fan spins freely by hand with the power off, fan fault code at the display
- Fan runs but no ignition — on an APS boiler: pressure switch tubes, switch contacts, flue restriction; on a premix boiler: tacho signal, fan speed within range, flue or condensate blockage that reduces air flow (many premix boilers report "fan speed error" when the flue is blocked)
- Condensate — a blocked or frozen condensate trap or pipe backs up into the sump and flue, loads the fan and causes gurgling then lockout; the fan is blamed and is innocent. See condensate pipe frozen boiler lockout
- Flue — a blocked terminal (bird guard, wasps' nest, leaves), a crushed or disconnected flue, or a terminal under a canopy or near a wall recirculating products all change the fan's load and note. Flue inspection comes before fan replacement every time
- Replacement — fan assemblies are supplied with the housing and often the venturi; 1–2 hours including case removal, gaskets, re-commissioning; parts £100–£300 trade (£300–£500 on some premium premix boilers); fitted £200–£450 regionally, £260–£550 London
- Combustion check after replacement — a flue gas analysis to the manufacturer's instructions is mandatory practice on a premix boiler after any change to the fan, venturi or gas valve, because the fan sets the air-gas ratio; record CO, CO₂ and CO/CO₂ ratio at maximum and minimum rate
- Who may do it — anything behind the case seal is work on a gas appliance; Gas Safety (Installation and Use) Regulations 1998, Regulation 3, requires a Gas Safe registered engineer with the domestic boiler category (CENWAT) on their card
- Electrical safety — isolate at the fused spur and verify dead before removing the fan; premix fan supplies are low voltage but the PCB side is 230 V; Electricity at Work Regulations 1989
- Age — fans fail from 8–15 years in normal use; a fan on a 20-year-old boiler is one of several parts due, and the honest conversation about replacement belongs on this visit
- Noise that is not the fan — pump bearings (a lower-pitched rumble that continues after the burner stops), kettling in the heat exchanger (a rumble or bang as the burner runs), expansion noise in pipework, a gas valve hum; see boiler kettling and pump noise
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Symptom | Most likely cause | Confirming test | Fix |
|---|---|---|---|
| High-pitched whine or scream, varies with fan speed | Fan motor bearings | Noise follows fan start and stop, not pump | Replace fan assembly |
| Grinding, sometimes stopping and starting | Bearings collapsing; impeller touching housing | Spin by hand (power off): rough or notchy | Replace fan assembly |
| Rattle or buzz, worse at low speed | Loose fan fixings or housing; debris in impeller; cracked impeller | Inspect; tighten; look for debris | Secure or replace |
| Whistle or howl, louder at high rate | Flue or air inlet restriction; terminal obstruction; wrong flue length or extra bends | Inspect flue and terminal; check pressure differential | Clear or correct flue |
| Hum, fan does not turn | Seized rotor, failed winding, or voltage present but no PWM signal | Spin by hand; check supply and control signal at the plug | Replace fan; or PCB if signal absent |
| Fan does not start, no hum, display shows demand | No supply at the fan plug | Check supply per wiring diagram | PCB or wiring fault |
| Fan runs, no ignition, APS boiler | Pressure switch, tubes, weak fan, flue restriction | Check tubes; measure switch operation; inspect flue | Replace APS or tubes; replace fan if weak; clear flue |
| Fan runs, no ignition, premix boiler | Tacho fault, fan speed out of range, flue or condensate blockage | Read fault code; check condensate; inspect flue | Clear blockage; replace fan if tacho faulty |
| Fan runs continuously, boiler not firing | Post-purge extended due to overheat; PCB fault; flue thermostat tripped | Check overheat stat, flue stat, fault history | Investigate cause of overheat; PCB |
| Gurgling then fan noise then lockout | Condensate backing up into sump | Check condensate trap and external pipe | Clear and thaw; re-route or lag condensate |
Detailed Guidance
Start outside: the flue
Before the case comes off, look at the flue terminal. A horizontal terminal with a bird guard clogged with debris, a terminal that has been boxed in by a new fence panel or canopy, a vertical terminal with a nest, or a plume kit with a joint that has dropped, all restrict the fan's air path and produce a note the customer describes as "the fan screaming". On a premix boiler a restricted flue changes the air-gas ratio, the fan compensates up to its limit, and then the boiler locks out with a fan or ignition code. If the terminal is clear, check the flue run inside: the fall on a horizontal concentric flue (back towards the boiler on a condensing appliance, typically 2–3° so condensate runs to the sump), the joints and clips at each section, and the flue length and number of bends against the manufacturer's maximum. A flue over length or with an extra 90° bend added during a loft conversion is a fan running at the top of its range with the noise to match. See flue types.
Decision tree
Boiler fan noisy or not running
│
├── Is the noise from the fan? (isolate: does it start/stop with the fan,
│ before ignition and after the flame, not with the pump?)
│ ├── No → pump bearings / kettling / gas valve hum / pipework → other guide
│ └── Yes → continue
│
├── Flue terminal and run clear, correct fall, joints sound?
│ ├── No → clear or correct the flue; re-test; the fan may be fine
│ └── Yes → continue
│
├── Condensate trap and pipe clear (condensing boiler)?
│ ├── No → clear/thaw; re-test
│ └── Yes → continue
│
├── Fan runs?
│ ├── Yes, noisy
│ │ ├── Whine / grind / scream, follows speed → bearings → REPLACE FAN
│ │ ├── Rattle / buzz → check fixings, housing, impeller for debris
│ │ │ or cracks → secure; replace if impeller damaged
│ │ └── Whistle / howl → flue, air inlet, venturi, or gasket leak
│ │ at fan-to-heat-exchanger joint → inspect and seal
│ └── No
│ ├── Hums but does not turn → rotor seized or winding → spin by hand
│ │ (power off): stiff = REPLACE FAN; free = check control signal
│ ├── Silent, supply present at plug (per wiring diagram) → REPLACE FAN
│ ├── Silent, no supply → PCB, fan relay, wiring, or no demand
│ │ (check overheat stat, pressure, flue stat, controls)
│ └── Silent, fault code → read code; follow manufacturer's chart
│
└── Fan runs but no ignition?
├── APS boiler → tubes split/blocked? switch contacts? fan weak?
│ → replace tubes or APS; if fan cannot make switch → REPLACE FAN
└── Premix boiler → tacho signal? speed in range? flue/condensate?
→ clear blockage; if tacho or speed fault persists → REPLACE FAN
Premix fans and the gas-air ratio
On a modern condensing boiler the fan draws air through a venturi; the gas valve supplies gas in proportion to the air flow (a pneumatic 1:1 valve) or under PCB control informed by the fan speed and sometimes an ionisation signal. The PCB sets the fan speed to the heat demand and reads the tacho; if the speed is outside the expected band for the commanded signal, the boiler locks out before releasing gas. Three consequences for the diagnosis:
- A fan that spins but reports no tacho, or the wrong speed, is a fan fault even though it "works".
- A blocked flue, a blocked air inlet or a condensate backup changes the pressure the fan works against; the speed-for-signal relationship shifts, and the boiler blames the fan. Clear the blockage first.
- A new fan, or a new venturi, changes the air flow for a given speed; the combustion must be checked with a flue gas analyser and adjusted (if the boiler allows adjustment) to the manufacturer's CO₂ and CO/CO₂ ratio figures at maximum and minimum rate. Fitting a fan without the combustion check is incomplete work and, on some boilers, a safety defect.
Air-pressure-switch boilers
Older fan-flued and early condensing boilers prove the fan with a differential pressure switch. Two silicone tubes connect the switch to pressure tappings on the fan housing or flue collector; when the fan runs, the pressure difference closes the switch contacts and the PCB proceeds to ignition. The faults in order of frequency: split, perished or kinked tubes; water in the tubes (condensate); a switch whose diaphragm has hardened; a fan that runs but has lost performance and can no longer make the switch; a flue restriction reducing the differential. Test by confirming the switch changes state when the fan runs (continuity across the contacts, or by the manufacturer's method), and by checking the tubes. A weak fan that just makes the switch on a mild day fails on a windy one — the classic "it only cuts out when it's windy" call.
Replacing the fan
Isolate electrically and verify dead. Close the gas service cock (good practice even though the fan is not a gas-carrying part on most boilers; on premix boilers the venturi and gas feed come off with the fan). Remove the case and, on a room-sealed boiler, note the condition of the case seal — a damaged seal is replaced, because the case is part of the combustion-air path. Disconnect the fan plug and tacho plug, remove the fan from the air box or the heat-exchanger door, and transfer or renew the gasket between fan and burner door (supplied with the fan or as a separate part — order it). Fit the new fan, torque the fixings evenly, reconnect, refit the case and seal, open gas, restore power, run the boiler through ignition and check the pre-purge and tacho signal behave. Then the combustion check: analyser in the flue sampling point, CO₂ and CO at maximum rate, then at minimum rate, compared with the manufacturer's figures; adjust the gas valve offset if the instructions require and permit it. Record the readings on the job sheet and in the Benchmark log if there is one. Complete with a gas tightness test if any gas joint was disturbed (BS 6891:2015+A1:2019 procedure on the installation pipework; the appliance test to the manufacturer's method).
What it costs and what to tell the customer
| Job | Time | Parts | Typical charge |
|---|---|---|---|
| Diagnose fan versus flue versus condensate | 30–60 min | — | Call-out £70–£130 |
| Clear flue terminal, re-seat flue joint | 30–60 min | £0–£30 | £90–£180 |
| Replace APS tubes or air pressure switch | 30–60 min | £10–£60 | £100–£200 |
| Replace fan assembly, standard boiler | 1–2 h | £100–£300 | £200–£450 |
| Replace fan assembly, premium premix (with venturi) | 1.5–2.5 h | £250–£500 | £350–£650 |
| Replace fan plus PCB (fan fault took the PCB relay) | 2–3 h | £250–£600 | £450–£900 |
On a boiler over 12 years old with a fan due and other parts obsolete or expensive, give the replacement price alongside the repair; the customer who spends £450 on a fan in October and £600 on a heat exchanger in January is not a happy customer. See boiler repair pricing guide and boiler installation pricing guide.
Safety points that are not optional
- The case seal on a room-sealed boiler: damaged or missing, it is a defect to be rectified before the appliance is left in use, because the appliance is no longer room-sealed.
- Any flue joint disturbed: re-make with the correct clips and seals; a flue fault is an "Immediately Dangerous" or "At Risk" classification under the Gas Industry Unsafe Situations Procedure depending on its nature.
- CO alarm: recommend one in the room with the appliance if not present (BS EN 50291 alarm, sited per BS EN 50292); it is required in rented homes in England under the 2022 amendments to the Smoke and Carbon Monoxide Alarm Regulations.
- Never bypass a tacho or pressure switch to "prove" the boiler: the proving device is the safety interlock between the fan and the gas.
Frequently Asked Questions
Why is my boiler fan so loud?
Most often because the fan motor's bearings are wearing — a whine or grinding that rises and falls with the fan and stops when the burner shuts down. Less often, a restricted flue or air inlet is making the fan work at the top of its range and howl, or a loose fixing is rattling. Bearing noise is cured only by replacing the fan; a flue restriction is cleared and the fan recovers.
Can I run my boiler with a noisy fan?
A noisy fan is a worn fan, and it will stop at some point, usually in cold weather. The boiler's interlocks will prevent it firing without the fan, so the risk is loss of heating rather than danger, but the noise can also indicate a flue problem that should be checked. Book a Gas Safe engineer rather than waiting for the lockout.
How much does it cost to replace a boiler fan?
£200–£450 fitted regionally and £260–£550 in London for a standard fan assembly, including the combustion check afterwards; some premium premix boilers have fan and venturi assemblies at £250–£500 for the part alone, taking the job to £350–£650. If the fan failure has damaged the PCB, add £250–£400.
Can a boiler fan be repaired rather than replaced?
No. The fan assembly is a sealed brushless motor and impeller matched to the boiler; bearings are not serviceable and a replacement impeller alone is rarely available. Loose housings and debris can be dealt with, but a motor that is noisy or seized is replaced as a unit, with its gasket, and followed by a combustion check.
Is replacing a boiler fan a Gas Safe job?
Yes. The fan sits behind the case seal, in the combustion-air path, and on premix boilers it carries the venturi and sets the gas-air ratio. Removing the case and working on the appliance is gas work under the Gas Safety (Installation and Use) Regulations 1998 and must be done by a Gas Safe registered engineer holding the domestic boiler category.
Regulations & Standards
Gas Safety (Installation and Use) Regulations 1998 (SI 1998/2451) — Regulation 3 competence; Regulation 26 appliance work; Regulation 35 duties of engineers
Gas Safe Register — Technical Bulletins and the Gas Industry Unsafe Situations Procedure (IGEM/G/11) — classification of flue and case-seal defects
BS 5440-1:2008 — flueing and ventilation for gas appliances of rated input not exceeding 70 kW; flue inspection and terminal positions
BS 6798:2014 — specification for selection, installation, inspection, commissioning, servicing and maintenance of gas-fired boilers of rated input not exceeding 70 kW net
BS 6891:2015+A1:2019 — installation of low-pressure gas pipework; tightness testing after disturbance
BS 7967 series — carbon monoxide in dwellings and other premises; measurement and procedures (BS 7967:2015 code of practice)
Building Regulations 2010, Approved Document J — combustion appliances and fuel storage systems; flues
Building Regulations 2010, Approved Document L, Volume 1 (2021) — commissioning and the Benchmark checklist
Electricity at Work Regulations 1989 (SI 1989/635) — safe isolation before working on the fan and PCB
BS EN 50291-1:2018 and BS EN 50292:2013 — carbon monoxide alarms; selection and siting
Smoke and Carbon Monoxide Alarm (England) Regulations 2015 (as amended 2022) — CO alarms in rented homes with fixed combustion appliances
Gas Safe Register — Gas safety for engineers — registration, competence categories, technical bulletins
HSE — Gas Safety (Installation and Use) Regulations 1998 Approved Code of Practice (L56) — appliance work and competence
IGEM — Gas Industry Unsafe Situations Procedure — classification of defects
Approved Document J: Combustion appliances and fuel storage systems — gov.uk
HHIC — Benchmark commissioning checklist — recording combustion readings
BS 6798:2014 — BSI Knowledge — servicing and maintenance of domestic gas boilers
boiler not firing — the wider no-ignition diagnosis
boiler short cycling diagnosis — when the fan is fine and the boiler keeps stopping
condensate pipe frozen boiler lockout — the blockage that gets blamed on the fan
boiler kettling — heat-exchanger noise that sounds like the fan
pump noise — pump bearings, the other whine
flue types — flue runs, falls and terminal positions
flue gas analysis — the combustion check after a fan change
boiler servicing — what a service should have caught
boiler repair pricing guide — pricing the repair