Summary
Radiator valve replacement is one of the few heating jobs where the material is cheap, the labour is predictable and the pricing errors are all in the ancillaries. A TRV body and head costs less than a takeaway; the money is in whether the system has to be drained, whether the old tail will come out of the radiator without wrecking the thread, whether the pipework is microbore or 15 mm, whether the valve is on the flow or the return, and whether the customer expects you to leave the system cleaned and inhibited afterwards. Engineers who price "£60 a valve" and then spend an afternoon fighting seized 1980s tails and a sludged system lose money on a job that should be their easiest earner.
There is also a regulatory driver. Approved Document L Volume 1 (England, 2021 edition, applying from June 2022) carries forward the Boiler Plus requirement that a replacement boiler in an existing dwelling must have time and temperature control with boiler interlock, and that the heating system should have individual room temperature control, which in practice means TRVs on every radiator except those in the room with the room thermostat. Wales and Scotland have parallel requirements. A boiler swap quote that does not include TRVs on an old system is incomplete.
This guide prices the single-valve call-out, the whole-house upgrade, the smart-TRV retrofit and the complications: microbore, seized tails, non-standard thread, no drain-off, sealed versus open-vented systems. It gives the time allowances, the materials list and the margin logic. For how to install and position the valves see trv installation; for valve types and heads see thermostatic radiator valves and radiator valves.
Key Facts
- TRV standard — BS EN 215:2019 covers thermostatic radiator valves; look for the Keymark or TELL rating label. Lockshield and manual valves are to BS 2767:1991 (manually operated copper alloy valves for radiators).
- Head thread — M30 × 1.5 is the near-universal modern standard; some older bodies use M28 × 1.5 or proprietary clip fittings, which matters when fitting smart heads.
- Valve body — 15 mm compression is standard; 10 mm and 8 mm microbore adaptors or dedicated microbore valves are needed on 1970s–90s systems; ½" BSP radiator tail is standard.
- Material cost (trade) — basic TRV and lockshield pack £12–£25; mid-range bi-directional TRV with lockshield £20–£45; angled or straight bodies the same price; smart TRV head £45–£90 each plus a hub or gateway at £60–£150.
- Consumables per valve — PTFE tape or jointing compound, new tails if the old ones are damaged (£3–£6 each), new olives.
- Labour time — 30–45 minutes per valve once the system is drained or the pipe is frozen; 45–75 minutes for a single valve including local drain-down and refill; 3–5 hours for eight radiators including full drain, refill, bleed and balance.
- Drain-down — allow 30–60 minutes to drain and refill an open-vented system; sealed systems need repressurising to 1–1.5 bar cold and the expansion vessel checked.
- Pipe freezing — a freeze kit (£25–£60 per job in cans, or an electric freezer) avoids a drain-down for one or two valves; budget 20 minutes per freeze.
- Inhibitor — one litre treats a system of up to 10 radiators (around 100 litres); £12–£20 trade. BS 7593:2019 requires the system to be cleaned and inhibited after work and the inhibitor level checked annually.
- Bi-directional valves — fit a bi-directional TRV where you cannot confirm flow direction; a uni-directional valve fitted on the return will hammer.
- Boiler Plus / ADL Volume 1 — replacement boilers in England need boiler interlock and time and temperature control; the system should have TRVs or equivalent zoning. Fitting TRVs is the normal way to meet the room-by-room control intent.
- Bypass — a system fully fitted with TRVs needs an automatic bypass valve (ABV) unless the boiler has an internal bypass; £15–£30 and 30 minutes to fit.
- Hourly rates — heating engineer £45–£75 outside London, £65–£110 London; see plumber hourly rate guide and gas engineer hourly rate guide.
- Margin — material markup 20–40%; labour priced at your charge-out rate; see markup to margin explained.
- VAT — 20% standard rate on labour and materials for repairs and replacements. The 0% rate on energy-saving materials (until March 2027 in Great Britain) covers heating controls installed with a qualifying measure but is unlikely to apply to a standalone valve swap; check the HMRC notice before applying it.
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Materials (your cost) | Labour time | Your cost | Customer price (20–30% margin) |
|---|---|---|---|---|
| One TRV, pipe frozen, no drain | £25–£45 | 1.0–1.25 h | £80–£130 | £95–£165 |
| One TRV with local drain and refill | £30–£50 | 1.25–1.75 h | £95–£160 | £120–£200 |
| Three TRVs, drain, refill, inhibitor | £75–£140 | 2.5–3.5 h | £200–£380 | £250–£480 |
| Eight TRVs and lockshields, full drain, refill, inhibitor, balance | £170–£320 | 4–6 h | £380–£720 | £480–£900 |
| Eight TRVs plus automatic bypass valve | £190–£350 | 4.5–6.5 h | £420–£800 | £520–£1,000 |
| Eight smart TRV heads onto existing M30 bodies | £400–£750 (plus hub) | 2–3 h | £500–£950 | £650–£1,200 |
| Microbore system, eight valves with adaptors | £220–£380 | 5–7 h | £470–£880 | £580–£1,100 |
| Add TRVs to boiler replacement (8 rads, system already drained) | £170–£320 | 2.5–3.5 h | £290–£560 | £360–£700 |
Prices are 2024 regional England, exclusive of VAT. Add 25–40% for London. The customer price column shows typical quoted figures; apply your own charge-out rate and margin.
Detailed Guidance
Pricing the single-valve call-out
The single stuck or leaking TRV is the most common request and the one most often underpriced. The call-out is fixed cost: travel, diagnosis, the valve itself, and either a freeze or a drain. A realistic structure is a minimum charge covering the first hour plus materials, then time thereafter.
Decide the method before you quote:
SINGLE TRV REPLACEMENT — METHOD CHOICE
│
├─ Is there a drain-off cock below the radiator level, accessible?
│ ├─ Yes ──> Partial drain (radiator circuit) ~40 min + refill/bleed ~20 min
│ └─ No ──> Freeze kit on both pipes ~20 min, or full drain via radiator valve/hose
│
├─ Sealed system?
│ └─ Yes ──> Add 15 min: repressurise to 1–1.5 bar, check filling loop, check vessel charge
│
├─ Open-vented?
│ └─ Yes ──> Tie up ball valve in F&E tank; refill via tank; bleed all upper rads
│
└─ Is the old tail damaged / does the thread strip on removal?
└─ Yes ──> Add new tail (£3–£6) + 15 min; warn customer of possible radiator replacement if thread is gone
Quote the single valve at £95–£165 outside London depending on method. Always state in the quote that the price assumes the existing radiator tail is reusable and that a seized or damaged tail will be charged as an extra at a stated price. That one sentence removes most disputes.
Pricing the whole-house upgrade
Eight radiators is a typical three-bed semi. The work sequence is drain, remove all valves, fit new TRVs and lockshields (replace the lockshields at the same time; the extra £5 a valve is nothing against a return visit for a weeping 20-year-old lockshield), refill, bleed, dose inhibitor, balance, and set TRV heads. A competent engineer does this in 4–6 hours alone.
Material list for eight radiators:
| Item | Quantity | Trade cost |
|---|---|---|
| TRV with matching lockshield, 15 mm | 8 | £120–£280 |
| Replacement tails ½" BSP | 4 (allowance) | £15–£25 |
| Inhibitor, 1 litre | 1 | £12–£20 |
| PTFE, jointing compound, olives | — | £5–£10 |
| Automatic bypass valve (if required) | 1 | £15–£30 |
| Hose, drain-off fittings, rags | — | £5 |
| Total | £170–£370 |
Exclude the radiator in the room with the room thermostat from TRV control (fit a lockshield or manual valve there) unless the customer wants a smart system that handles the interaction. Price the balance properly: it is the half-hour that makes the customer notice the house heats evenly, and it is why they recommend you.
Microbore, non-standard threads and other complications
Microbore (8 mm and 10 mm) systems need either dedicated microbore valves or reducing adaptors into 15 mm bodies. Adaptors cost £2–£5 a pair but the pipework is fragile, kinks easily and often emerges from the floor at awkward offsets. Add 30–50% to labour and tell the customer in advance that a kinked pipe may need a short section replaced.
Older systems can present ¾" BSP tails, imperial 1/2" copper (which 15 mm compression fittings grip but do not seal reliably without the correct olive) and corroded steel radiators whose tails will not shift. Where the radiator is 25 years old and the tail will not come out cleanly, pricing a new radiator is often cheaper than two hours of struggling; see radiator replacement pricing guide.
Flow direction matters. Most modern TRVs are bi-directional, but if you are fitting cheap uni-directional bodies, confirm the flow side. On a system with the pump on the flow, the flow pipe heats first; on an unfamiliar layout, fit bi-directional valves and remove the risk entirely.
Smart TRV retrofits
Smart heads replace the existing TRV head on an M30 × 1.5 body with a motorised head controlled by an app or hub. Pricing points:
- Heads cost £45–£90 each at trade; most systems need a hub or bridge at £60–£150, and some need a wiring-centre receiver to call for heat from the boiler (£60–£120 plus 1–1.5 hours wiring).
- Fitting a head onto an existing good M30 body takes 10–15 minutes including pairing. Where bodies are old, non-M30 or sticking, replace the bodies first and price it as a full replacement plus heads.
- Batteries typically last 1–2 years; tell the customer.
- Boiler interlock: a smart TRV system that only closes valves without calling for heat leaves the boiler cycling against a bypass. Make sure the design includes a call-for-heat path.
A reasonable customer price for eight smart heads onto good bodies, with a hub, commissioning and app setup, is £650–£1,200.
Adding TRVs to a boiler replacement
The system is already drained for the boiler swap, so the marginal labour per valve drops to 20–30 minutes. Quote TRVs as a separate line on the boiler quotation at £45–£80 per radiator installed, and explain that Approved Document L Volume 1 expects room-by-room control on a replacement boiler. The line is cheap for the customer, improves the system's efficiency, and protects you at building control notification. See boiler plus requirements explained for what the rules demand.
Margin and presentation
Price materials at trade cost plus 20–40%. Price labour at your charge-out rate, not your wage; a self-employed heating engineer with van, tools, Gas Safe registration, insurance and unpaid admin time needs £45–£75 an hour outside London to make a living wage. Present the quote as a fixed price with stated assumptions (tails reusable, system holds pressure after refill, no pipework alterations) and stated extras (replacement tail £X, replacement radiator from £Y, additional drain-off cock £Z). Fixed prices with clear exclusions win work; hourly estimates frighten customers and invite arguments.
Frequently Asked Questions
Do I have to drain the whole system to change one TRV?
No. If there is an accessible drain-off cock below the radiator, you can drain just enough to bring the level below the valve. If not, freezing both pipes with a freeze kit lets you change the valve in ten minutes with no drain at all. On sealed systems the freeze method avoids disturbing the pressurisation too. Isolating the radiator by closing both valves and catching the radiator's contents works for changing a head or a lockshield but not for changing the TRV body itself, because the body is the isolation.
Should I fit a TRV in the room with the room thermostat?
Normally no. The room thermostat controls the boiler; if a TRV in the same room closes before the thermostat is satisfied, the boiler keeps running against a bypass and never switches off. Fit a lockshield or manual valve on that radiator, or leave the TRV fully open as a decorator's cap. Smart systems that use TRVs as the room sensors are the exception and should be designed as a whole.
Do all-TRV systems need a bypass?
Yes, unless the boiler has an internal automatic bypass (most modern combis do; many system and regular boilers do not). When every TRV closes, the pump needs a path for flow or the boiler overheats and locks out. Fit an automatic bypass valve between flow and return, after the pump and before any zone valve, set to open at about 0.2–0.3 bar above the system's normal differential. Check the boiler manufacturer's instructions; they override the general rule.
Can I claim 0% VAT on TRVs as energy-saving materials?
Only in narrow circumstances. The zero rate for energy-saving materials in Great Britain (extended to 31 March 2027) covers "controls for central heating and hot water systems" when installed in residential accommodation, which in principle includes TRVs installed as a heating control. HMRC's notice is specific about what qualifies and about the ancillary-supply rule when controls are installed alongside a boiler, which is not itself zero-rated. Read VAT Notice 708/6 and take advice before zero-rating; getting it wrong leaves you paying the VAT yourself.
How long should a TRV last?
A decent BS EN 215 valve lasts 10–15 years. Common failures are a stuck pin (often freed by tapping or working it with pliers, a 10-minute fix rather than a replacement), a worn gland that weeps around the spindle (a replacement gland or O-ring if the manufacturer supplies one), and a head whose wax capsule has failed so the radiator stays on or off regardless of setting. Tell the customer which fault they had; a freed pin should not be invoiced as a new valve.
Regulations & Standards
BS EN 215:2019 — Thermostatic radiator valves. Requirements and test methods.
BS 7593:2019 — Code of practice for the preparation, commissioning and maintenance of domestic central heating and cooling water systems; requires cleaning, inhibitor dosing and annual checks.
Building Regulations 2010, Approved Document L Volume 1: Dwellings (2021 edition) — minimum controls for new and replacement heating systems in England, incorporating the former Boiler Plus requirements.
Domestic Building Services Compliance Guide (2021) — the detailed control specifications referenced by Approved Document L.
Building Regulations Part L (Wales) and Scottish Building Standards Section 6 — parallel controls requirements outside England.
Gas Safety (Installation and Use) Regulations 1998 — where the valve work forms part of a boiler installation; non-gas valve work itself is not gas work.
Water Supply (Water Fittings) Regulations 1999 — relevant to filling loops and backflow protection on sealed systems.
VAT Notice 708/6 — Energy-saving materials and heating equipment; the zero-rate rules for heating controls.
Approved Document L, Volume 1: Dwellings (2021 edition) — controls requirements for replacement boilers and heating systems
Domestic Building Services Compliance Guide — detailed minimum standards for heating controls
HMRC VAT Notice 708/6: Energy-saving materials and heating equipment — zero-rate rules
BSI – BS EN 215:2019 — the TRV product standard
Heating and Hotwater Industry Council – Boiler Plus guidance — industry explanation of the controls requirements
BEAMA – Guide to heating controls — controls selection and interlock guidance
trv installation — how to fit and position the valve this guide prices
thermostatic radiator valves — valve types, heads and selection
radiator valves — valve terminology and matching bodies to heads
boiler plus requirements explained — the controls rules that make TRVs a boiler-swap requirement
central heating one radiator cold — the diagnosis that often ends in a TRV replacement
plumber hourly rate guide — setting the labour rate behind these prices