Summary
Plumbing has the widest spread of hourly rates of any domestic trade, because the word covers everything from a £90 tap washer to a £4,000 unvented cylinder installation and from a Monday-morning appointment to a 2 am burst pipe. A single headline hourly rate does not describe that range, and a plumber who quotes one — "I'm £40 an hour" — ends up subsidising the small jobs, the travel and the paperwork with the big ones. The structure that works is a call-out or first-hour charge that covers getting there and diagnosing, an hourly rate after that for open-ended work, and fixed prices built from the hourly rate for everything that can be scoped in advance.
The other reason plumbers under-price is the employed comparison. Customers who have seen "plumber salary £32,000" on a jobs board are seeing an employed figure with the employer's van, insurance, tools, holiday pay, pension and dead time stripped out. A self-employed plumber's rate has to fund all of that, plus the specific costs of the trade: WRAS and Water Regulations training to work on the supply side, the Gas Safe registration and ACS assessments if you do heating, the G3 unvented qualification if you install cylinders, and the van stock — fittings, valves, pipe, consumables — that is bought ahead of need and sits as working capital. This guide builds the hourly rate from real 2026 costs, gives the regional market figures, sets out the call-out and minimum-charge structure, and benchmarks the common fixed-price jobs so you can check your own.
For the method across all trades see pricing labour; for converting between day and hourly rates see day rate to hourly rate calculator; for emergency work see emergency callout pricing guide.
Key Facts
- Hourly rate, 2026 — £45–£70 outside London and the South East; £55–£85 South East; £65–£110 London. Gas Safe heating engineers £10–£20 above the general plumbing figure in each band
- Day rate — £250–£380 regionally, £300–£430 South East, £350–£500 London, consistent with the 2024 figures in pricing labour plus two years of cost inflation
- Call-out / first hour — £80–£150 daytime, covering travel, the first hour on site and diagnosis; hourly rate applies after that. Never quote an hourly rate with no minimum
- Emergency call-out — £120–£250 evenings, weekends and bank holidays plus the hourly rate at a 50–100% uplift; see emergency callout pricing guide
- Billable hours per day — 6.5–7 once travel between jobs, merchant visits, van restocking and invoicing are allowed for; divide the day rate by this, not 8
- Billable days per year — 200–215 for a sole trader after holidays, training, quoting, sickness and chasing payment
- Gas Safe registration — £300–£400 a year for a sole trader; ACS core and appliance assessments every 5 years at £700–£1,200; flue gas analyser £400–£900 with annual calibration £60–£120. See gas safe requirements
- G3 unvented — qualification £250–£400 renewed every 5 years; required to install or commission unvented cylinders and to self-certify Part G notifiable work; see unvented cylinders
- WRAS / Water Regulations — approved contractor schemes (WaterSafe) allow self-notification of work under the Water Supply (Water Fittings) Regulations 1999; a day's training at £150–£300; see water regulations
- Insurance — public liability £2 million minimum, £5 million often required for landlord and commercial work; £500–£900 a year; see public liability insurance guide
- Van stock — £1,500–£4,000 of fittings, valves, pipe, flexi hoses, compression and push-fit stock on the van at any time; this is working capital and the markup on it is how it earns its keep
- Materials markup — 20–35% on trade cost for small fittings (the picking and carrying cost is high relative to the item), 15–25% on cylinders, boilers and sanitaryware
- Parts on emergency work — charge list price plus the markup; the customer is paying for the fact that you had the part on the van at 11 pm
- Fixed-price benchmarks — tap replacement £90–£180 labour; toilet cistern internals £90–£160; outside tap £150–£300; radiator swap £120–£220; boiler service £80–£130; see the Quick Reference Table
- VAT — compulsory registration above £90,000 taxable turnover in any rolling 12 months; domestic customers cannot reclaim it, so a plumber at £55 unregistered is cheaper to them than one at £50 registered
- CIS — applies to plumbing work for a contractor, not to work direct for a homeowner; 20% deducted at source on the labour element if registered, 30% if not; see cis tax explained
- Consumer Rights Act 2015, s.51 — reasonable price where none agreed; a written hourly rate, call-out and estimated hours protect both sides
- Building Regulations Part G — sanitation, hot water safety and water efficiency; unvented cylinder work is notifiable under Part G3
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Charge | Regional (outside London/SE) | South East | London | Notes |
|---|---|---|---|---|
| Hourly rate (after first hour) | £45–£70 | £55–£85 | £65–£110 | Self-employed, insured, WaterSafe/Gas Safe |
| Call-out / first hour (daytime) | £80–£150 | £100–£170 | £120–£200 | Includes travel and diagnosis |
| Emergency call-out (out of hours) | £120–£250 | £150–£280 | £180–£350 | Plus hourly at 50–100% uplift |
| Day rate | £250–£380 | £300–£430 | £350–£500 | 6.5–7 billable hours |
| Half-day minimum | £150–£220 | £180–£260 | £220–£300 | Small installs that cannot share a day |
| Replace kitchen or basin mixer tap (customer-supplied) | £90–£180 | £110–£200 | £140–£250 | Within first hour if isolation valves present |
| Replace toilet fill valve / flush valve | £90–£160 | £100–£180 | £130–£220 | Plus part £15–£40 |
| Fit outside tap, new supply | £150–£300 | £180–£340 | £220–£400 | Double-check valve required |
| Swap a radiator like-for-like | £120–£220 | £140–£250 | £180–£300 | Plus radiator; drain-down adds £40–£80 |
| Replace stopcock | £120–£250 | £140–£280 | £180–£350 | More if internal stopcock seized and external needs freezing |
| Boiler service (Gas Safe) | £80–£130 | £90–£150 | £110–£180 | 45–60 minutes incl. analyser readings |
| Replace unvented cylinder (G3) | £1,600–£2,800 | £1,900–£3,200 | £2,300–£3,800 | Supply and fit, Part G notified |
| Leak tracing (hourly, no fixed price) | £60–£90/hr | £70–£100/hr | £85–£130/hr | After call-out; quote the fix separately |
Detailed Guidance
Building the hourly rate from your costs
Work forwards from costs. A sole-trader plumber (not Gas Safe) outside London:
| Item | Annual figure |
|---|---|
| Target income before tax | £40,000 |
| Van: finance or depreciation, insurance, tax, servicing, work fuel | £7,500 |
| Public liability insurance (£2 million) | £650 |
| Tools: press tool, freeze kit, pipe benders, power tools, replacement | £1,500 |
| Van stock financing and shrinkage (stock bought ahead, lost, out of date) | £800 |
| WaterSafe / WRAS scheme and training | £300 |
| Phone, accountant, invoicing software, card fees | £2,000 |
| Workwear, PPE, consumables not recharged | £500 |
| Advertising, website, directory listings, reviews platform | £1,200 |
| Pension contribution | £2,500 |
| Total to recover | £56,950 |
Divide by billable hours. A plumber who works 46 weeks and averages 4.5 billable days a week (the rest is quoting, merchants, admin and the inevitable no-shows) has roughly 207 billable days; at 6.5 billable hours a day that is 1,345 hours. £56,950 ÷ 1,345 = £42.30 an hour break-even for a £40,000 income. Charge £35 an hour and the income falls to about £30,000; charge £55 and it rises to about £57,000. For a Gas Safe engineer add roughly £1,500 a year (registration, ACS amortised, analyser and calibration) and the break-even moves to about £43.50; the market premium for gas work is larger than that because the demand is, which is why heating engineers sit £10–£20 above the plumbing rate rather than £1.
Why the first hour has to cost more
The hourly rate only works if someone pays for the gaps between jobs. A plumber doing four small jobs a day in different postcodes spends two hours driving and parking, loads and unloads four times, and writes four invoices. Charged purely by the hour on site, those four jobs produce four or five billable hours out of a nine-hour day. The call-out or first-hour charge is where the travel lives:
- Daytime call-out / first hour £80–£150 — covers getting there, parking, the first hour of diagnosis or work and the drive to the next job. For many small jobs this is the whole price
- Subsequent hours at the hourly rate, in half-hour increments after the first hour. State the increment; "£50 an hour" without one means a 65-minute job is argued over
- A minimum charge is not a call-out — if the customer wants a quote visit with no work, that is either free (your marketing decision) or a stated survey fee; do not confuse the two on the invoice
For a customer, "£95 for the first hour then £50 an hour" is clearer and fairer than "£60 an hour", and it pays better on the small jobs that make up most of a domestic plumber's week.
Fixed prices built from the rate
Most plumbing can be scoped on the phone or on a quote visit, and a fixed price is what customers prefer. The fixed price is the hourly rate multiplied by a realistic time allowance, plus a contingency for the things that go wrong on old plumbing, plus the parts at marked-up cost. A realistic allowance is not the time it takes you on a good day:
| Job | Good-day time | Realistic allowance | Why |
|---|---|---|---|
| Replace basin mixer tap | 30 min | 1.25 hrs | Seized back-nuts, no isolation valves, flexi tails wrong length |
| Replace toilet fill valve | 20 min | 1 hr | Cistern off to get at it, perished doughnut washer |
| Outside tap on 15 mm from kitchen | 1.5 hrs | 2.5 hrs | Drilling the wall, clipping, double-check valve, test |
| Radiator swap like-for-like | 1 hr | 2 hrs | Valves seize, drain-down, new tails, bleed and balance |
| Stopcock replacement | 45 min | 2 hrs | External stopcock seized, freeze kit, no isolation |
The fixed price for the tap is therefore 1.25 × £55 + call-out element ≈ £130–£150 labour, not 0.5 × £55 = £28. If the job goes well you earn above the rate; if it goes badly the contingency absorbs it; either way the customer knew the price. State what the fixed price assumes ("working isolation valves present; if not, isolation valves fitted at £X each") so that the exclusion is visible before, not after.
Leak tracing, fault-finding and the open-ended jobs
Some work cannot be fixed-priced honestly: tracing a leak behind a bath panel that might be a cracked trap or might be a failed shower tray seal, finding why a combi loses pressure, diagnosing an intermittent cold spot. Here the structure is call-out plus hourly, with the fix quoted separately once found. Say so at the start — "the first hour is £95, after that £55 an hour until we find it, and then I'll give you a price for the repair" — and give a running total at each hour. Customers accept open-ended charges when they are told in advance and kept informed; they refuse to pay them when they are a surprise on the invoice.
Access and making good are separate line items. Lifting a floor or cutting a bath panel to find a leak is part of the tracing; reinstating it is a quoted extra, and anything that needs a tiler or decorator is excluded in writing.
Gas, unvented and the premium for qualifications
A Gas Safe registered engineer sells two things a plumber cannot: the legal right to work on gas, and the certificates that landlords must have. The Gas Safety (Installation and Use) Regulations 1998 make it an offence for anyone not Gas Safe registered to work on gas appliances or pipework, and regulation 36 requires landlords to have an annual safety check and a Landlord Gas Safety Record. That statutory demand is why boiler services, LGSRs and breakdowns command a premium, and why the £10–£20 hourly uplift is a floor rather than a ceiling in winter.
Unvented cylinder work under Building Regulations Part G3 is notifiable and must be installed by someone holding the G3 qualification, and it is notified through a competent person scheme or Building Control. The qualification, the scheme membership and the notification time all belong in the rate for cylinder jobs, which is why an unvented replacement is a £1,600–£2,800 job and not £800 plus the cylinder.
Regional, London and out-of-hours pricing
The regional spread is roughly 40–50% from the cheapest regions to London. London carries parking (£15–£40 a day in inner boroughs, recharged as a disbursement), ULEZ on non-compliant vans, congestion charge and slower travel between jobs, which means fewer billable hours a day and a higher rate to compensate. Out-of-hours work is priced with a higher call-out (£120–£250) and an hourly uplift of 50–100%; the customer with water coming through the ceiling is paying for availability, and a plumber who does emergency work at daytime rates will stop answering the phone within a year. Publish the out-of-hours rate on your website and say it on the phone before you leave the house.
Quoting, deposits and payment terms
Give a written quote or, for small jobs, a written confirmation by text or email stating the call-out, the hourly rate, the increment and any fixed prices. Take a deposit for materials on anything over £500 (cylinders, bathrooms, boilers — 30–50%). Invoice on the day and take card payment on site; a card reader costs 1.5–2% and halves the time spent chasing money. For landlords and letting agents, agree 14-day terms in writing and build the delay into the rate. The Consumer Contracts Regulations 2013 give the customer a 14-day cancellation right on contracts agreed in their home; for urgent repairs get the written request to start within the cancellation period, or you can be asked to refund the labour.
Frequently Asked Questions
What is a fair hourly rate for a plumber in 2026?
£45–£70 an hour outside London and the South East for a self-employed, insured plumber, with a first-hour or call-out charge of £80–£150. In London £65–£110. A Gas Safe heating engineer is £10–£20 an hour more. Those figures produce a mid-£40,000s income before tax on 200–215 billable days, which is the right return for the skill, the van and the risk.
Should I charge a call-out fee?
Yes, or a first-hour charge that includes the travel — the two are the same thing by different names. Without it, a plumber doing short jobs across a town earns for the hour on site and gives away the hour getting there. State it on the website, on the phone and on the invoice so it is never a surprise.
How much more can I charge for emergency work?
A higher call-out (£120–£250 out of hours) plus the hourly rate at a 50–100% uplift. The customer is paying for availability at 11 pm, not for the half-hour it takes to fit an isolation valve. Publish the rate, say it on the phone before you leave, and take payment on site.
Why do heating engineers charge more than plumbers?
Because they carry costs and a legal status that plumbers do not: Gas Safe registration, ACS reassessment every five years, a calibrated flue gas analyser, and the right to issue the Landlord Gas Safety Record that landlords are legally required to hold. Statutory demand plus a restricted supply of registered engineers sets the premium.
Do I need to register for VAT as a plumber?
Only once taxable turnover passes £90,000 in a rolling 12 months. Many sole-trader plumbers approach it because materials pass through the turnover figure — a few bathroom installs with sanitaryware on the invoice can push a plumber over the threshold on quite modest labour income. Watch the rolling figure monthly; see vat registration for tradespeople.
Regulations & Standards
Consumer Rights Act 2015 (s.49–s.52) — reasonable care and skill; reasonable price where none agreed
Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013 (SI 2013/3134) — 14-day cancellation right for contracts agreed in the customer's home; request to start work within the period must be express
Gas Safety (Installation and Use) Regulations 1998 (SI 1998/2451) — regulation 3 (competence and registration), regulation 36 (landlord annual checks)
Water Supply (Water Fittings) Regulations 1999 (SI 1999/1148) — backflow protection, notification of certain work, approved contractor schemes
Building Regulations 2010, Approved Document G — sanitation, hot water safety (G3 unvented systems) and water efficiency; G3 work is notifiable
Income Tax (Construction Industry Scheme) Regulations 2005 (SI 2005/2045) — deduction at source on labour when working for a contractor
Value Added Tax Act 1994 — compulsory registration threshold £90,000 (from 1 April 2024)
Health and Safety at Work etc. Act 1974 — general duties of the self-employed whose work affects others
BS EN 806-1 to 806-5 — specifications for installations inside buildings conveying water for human consumption
BS 8558:2015 — guide to the design, installation, testing and maintenance of services supplying water for domestic use (complements BS EN 806)
Construction Industry Joint Council Working Rule Agreement and JIB-PMES (Plumbing Mechanical Engineering Services) rates — employed site rates for plumbers, for context only
Consumer Rights Act 2015, Part 1 Chapter 4 — services — reasonable price and reasonable care and skill
Gas Safe Register — registration fees and requirements — fees, ACS and who must register
HSE — Gas Safety (Installation and Use) Regulations 1998 (L56) — Approved Code of Practice and guidance
HM Government — Approved Document G — hot water safety and G3 notification
WaterSafe — approved contractor scheme — Water Regulations approved plumbers
HMRC — VAT registration thresholds — £90,000 compulsory threshold
pricing labour — the cost-based pricing method and 2024 baseline day rates
day rate to hourly rate calculator — converting between day rate, hourly rate and billable hours
emergency callout pricing guide — structuring out-of-hours call-outs and uplifts
electrician hourly rate guide — the equivalent guide for electricians, built the same way
boiler service pricing guide — pricing the Gas Safe service that anchors a heating engineer's year
outdoor tap installation pricing guide — a worked fixed-price example from the rate
unvented cylinders — the G3 qualification and notification behind cylinder pricing
vat registration for tradespeople — the £90,000 threshold and what it does to domestic pricing