Summary

Boiling water taps have moved from luxury to standard kitchen specification, and the installation is now a bread-and-butter job for kitchen fitters, plumbers and multi-trade installers. The pricing problem is that it sits across two trades and three possible scopes: plumbing the tank into the cold mains with a filter, providing a safe electrical supply for a 1.5–3 kW heating tank in a cupboard under a sink, and cutting or enlarging a tap hole in a worktop that may be laminate, solid timber, quartz or granite. Quote only the plumbing and you will either do the electrical work without a certificate or hand the customer an unexpected second bill.

The regulatory position is specific. The tank is a fixed appliance connected to the mains water supply, so the Water Supply (Water Fittings) Regulations 1999 apply: WRAS-approved or equivalent fittings, appropriate backflow protection (manufacturers specify a double check valve on the inlet) and an isolation valve. The electrical supply is a fixed connection, not a plug, in most manufacturers' instructions, so BS 7671:2018+A2:2022 governs it and Part P of the Building Regulations decides whether it is notifiable. Adding a fused spur to an existing kitchen ring is non-notifiable in England; running a new radial circuit from the consumer unit is notifiable and needs a registered competent person or a building control application.

This guide prices the three common scenarios (replace an existing mixer with a boiling tap where power already exists, install with a new fused spur, install with a new circuit), lists the materials and consumables, gives the time allowances, and covers the extras that catch installers out: stone worktop drilling, water softener and filter compatibility, low mains pressure and cupboard ventilation. For how to carry out the installation see boiling water tap installation.

Key Facts

Quick Reference Table

Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.

Try squote free →
Scenario Labour time Your labour and sundries cost Customer price, installation only (20–30% margin) Customer price, supply and fit (mid-range 4-in-1)
Swap existing mixer for boiling tap; socket or FCU already under sink; laminate worktop 2.5–3.5 h plumber £130–£260 £180–£340 £1,300–£2,100
As above plus new fused spur from existing kitchen ring 3–4 h plumber + 1–1.5 h electrician £220–£400 £300–£520 £1,450–£2,300
As above plus new radial circuit from consumer unit (notifiable) 3–4 h plumber + 3–5 h electrician £350–£650 £460–£850 £1,600–£2,600
Quartz or granite worktop needing 35 mm core add 0.75–1.5 h and £40–£80 core bit, or £120–£200 fabricator add £80–£200 add £100–£260 add £100–£260
Add pressure-reducing valve or inlet pressure problem add 0.5–1 h and £25–£50 add £45–£110 add £60–£140 add £60–£140
5-in-1 chilled/sparkling with CO₂ and second unit 5–7 h plumber + electrician £400–£750 £520–£980 £2,800–£4,500

Prices are 2024 regional England, exclusive of VAT at 20%. Add 25–40% for London. Tap and tank prices vary widely between brands; quote the supply element at your actual trade price plus margin.

Detailed Guidance

Survey before you price

Fifteen minutes under the sink prevents a loss. Check and record:

  1. Space. Tank dimensions plus ventilation clearance plus filter. A 600 mm base unit with a waste disposer, washing-machine trap and the boiler condensate already in it often has no room; you may need to move the trap or relocate the filter into the adjacent unit (add 0.5–1 hour).
  2. Power. Is there an existing socket or fused connection unit under the sink, on an RCD-protected circuit, with spare capacity? Many appliance sockets under sinks are on the kitchen ring; a fused spur off the ring is fine for a 1.5–3 kW tank, but check the ring is not already carrying a washer, dishwasher and tumble dryer on the same leg. Where the consumer unit has no RCD, price an RCD FCU or discuss a board upgrade.
  3. Water. Mains pressure (test with a gauge on an outside tap or the kitchen cold: 1.5–2 bar minimum dynamic, under 5–6 bar static), the location of the stop valve, whether the cold under the sink is mains or tank-fed (it must be mains), and whether there is a softener. Note the pipe size: 15 mm copper is standard; plastic push-fit is fine with inserts.
  4. Worktop. Material and thickness. The existing tap hole may be 32 mm where you need 35 mm; enlarging a hole in stone is slower than drilling a new one.
  5. Sink. Many boiling taps have a wide base; check the flange clears the sink edge and the tap can rotate without hitting the splashback.

Materials and consumables list

Item Trade cost Notes
Boiling water tap, tank and filter £350–£3,000 Customer-supplied or your supply with margin
WRAS-approved isolation valve, 15 mm £4–£8 Full-bore, lever type preferred
Double check valve, 15 mm £8–£15 Where not supplied with the kit
Pressure-reducing valve £25–£50 Only on high-pressure mains
Flexible connectors, push-fit tee, fittings £10–£25 Use manufacturer's hoses where supplied
Fused connection unit, 13 A switched, flex outlet £6–£15 RCD type adds £25–£45
2.5 mm² twin and earth, back box, cable clips £8–£20 For a spur from the ring
2.5 mm² or 4 mm² cable and MCB/RCBO for new radial £40–£90 Notifiable work
35 mm hole saw or diamond core £8–£80 Diamond core for stone
PTFE, sealant, wipes £5
Typical sundries excluding tap £60–£150 Rises to £150–£250 with a new radial

Scenario 1: like-for-like tap swap with power present

The simplest job. Isolate, remove the old mixer, enlarge or clean up the tap hole, fit the new tap, mount the tank, connect the filter and tank to the cold mains via the isolation valve and check valve, connect hot and cold to the tap, plug or wire into the existing FCU, fill, bleed, flush the filter for the manufacturer's stated time, test, set temperature. Allow 2.5–3.5 hours including commissioning and showing the customer how to operate the child-safe boiling function and change the filter.

Price at £180–£340 for labour and sundries. Do not forget the time it takes to flush a new filter and fill a tank; some units need 15–20 minutes before boiling water is available, and you should not leave before you have proven it.

Scenario 2: new fused spur required

Most installations. The plumber's work is as above; the electrician adds a 13 A switched fused connection unit spurred from the nearest kitchen ring socket, with the cable clipped or in trunking inside the unit and a flex outlet to the tank. In England this is non-notifiable but still requires a Minor Electrical Installation Works Certificate; give the customer the certificate. If the circuit lacks 30 mA RCD protection, fit an RCD FCU to satisfy Regulation 411.3.3 for the new accessory.

Multi-trade installers who hold the electrical competence do the whole job in 4–5 hours. Where two trades attend, price two call-outs and sequence them: electrician first so the plumber can commission.

Scenario 3: new circuit from the consumer unit

Needed where the manufacturer demands a dedicated circuit, where the kitchen ring is already heavily loaded, or where the board has no RCD protection and the customer declines an upgrade. A new 16 A or 20 A radial in 2.5 mm² or 4 mm² cable on an RCBO, routed from the board to the sink base. Time depends on the route: 3 hours for a kitchen adjacent to the board with an accessible route, 5 hours or more where the cable must be chased or run through the first floor. This is notifiable under Part P in England; a registered competent person self-certifies for £5–£15 per notification, otherwise a building notice costs £200–£400. Include the notification fee as a line.

Stone worktops and tap holes

Quartz and granite are drilled with a wet diamond core at low speed, from above with the surface masked, through a guide to prevent skating. It takes 20–40 minutes and the £40–£80 core bit is consumed in a few holes. Fabricators charge £120–£200 for a site visit to drill. Ceramic and sintered-stone tops (very hard, chip-prone) are best left to the fabricator. Always state in the quote who is responsible for the hole and what happens if the stone cracks: a replaced quartz worktop is a £1,500–£4,000 problem. Many installers exclude stone drilling entirely and require the customer to arrange it.

Water quality, pressure and softeners

Hard-water areas scale tanks fast; the filter is the manufacturer's answer, and the customer must change it on schedule or the warranty fails. If the house has a softener, check the instructions: most allow softened water, some set a maximum hardness, and a few advise a separate unsoftened feed for drinking water. Low mains pressure (common in rural areas and on long shared supplies) means the tank will not fill properly; above 5–6 bar a pressure-reducing valve is needed. Measure pressure at survey; it takes two minutes and saves a return visit.

Margin and what to include in the quote

Quote three lines: supply (if you supply) at trade cost plus 15–25%; installation as a fixed price with stated assumptions; and a stated list of extras (new spur, new circuit, stone drilling, pressure-reducing valve, trap relocation) each with a fixed price. State the ongoing filter cost and interval so the customer does not blame you in a year. Include the electrical certificate in the price. For how to set the labour rate behind these figures see kitchen fitter day rate guide and markup to margin explained.

Frequently Asked Questions

Can the tank just be plugged into a socket?

Some manufacturers supply a moulded plug and accept a socket; most specify a fused connection unit or a dedicated supply. Follow the instructions supplied with the unit: they form part of the appliance's safety case and the warranty terms. Even where a plug is permitted, an unswitched socket behind a tank in a wet cupboard is poor practice; a switched FCU at an accessible point lets the customer isolate the unit to change the filter.

Is a boiling water tap installation notifiable under Part P?

Only the electrical element can be notifiable, and only where it involves a new circuit from the consumer unit, work in a special location, or a consumer unit change. In England, adding a fused spur to an existing circuit in a kitchen has been non-notifiable since April 2013. In Wales the position differs because the 2013 relaxation was not adopted in the same form; check the current Welsh Government guidance before relying on non-notification. The plumbing is not notifiable but must comply with the Water Supply (Water Fittings) Regulations 1999, and some water undertakers ask to be notified of fittings in fluid category 3 or above.

Do I need a double check valve if the tank has its own?

Follow the manufacturer: most require a double check valve on the inlet because the tank holds heated water under pressure and is a fluid category 3 backflow risk. If the kit includes one, do not duplicate it unnecessarily, but ensure the check valve is between the mains isolation and the filter so the filter and tank are both protected. The Water Regulations Approval Scheme (WRAS) listing of the fitting is what the water undertaker will ask about if there is ever a dispute.

How long does the installation take?

A straightforward swap with power present is 2.5–3.5 hours. Add 1–1.5 hours for a fused spur, 3–5 hours for a new circuit, and up to 1.5 hours for a stone worktop hole. Quote a half-day for a standard job and a full day where a new circuit or stone drilling is involved; that protects you from a long morning turning into an unpaid afternoon.

What ongoing costs should I tell the customer about?

Filter cartridges at £40–£90 every 6–12 months, the standby electricity (most tanks draw 10–20 W on standby, around £25–£60 a year at 2024 unit rates), descaling in hard-water areas if the filter is neglected, and CO₂ cylinders for sparkling-water units. Telling the customer at quote stage is what stops the one-star review when the first filter reminder appears.

Regulations & Standards