Summary
A kitchen fitter's day is carpentry with a tape measure and a laser level: levelling and fixing base units, hanging wall units on a true line, scribing end panels and plinths, cutting and jointing laminate worktops, fitting doors and drawers so the gaps are even. The money is made or lost before any unit is unboxed, in the survey: whether the walls are square, whether the floor falls 20 mm across the room, where the existing services are and whether the plan the showroom drew fits the room they never measured. The fitter who prices from the showroom plan at a per-unit rate will lose a day to a wall that is 40 mm out of plumb and another to a soil pipe where the dishwasher was going.
The day rate carries the fitter's real costs and sets the variation rate; the fixed price is what the customer buys. The specialist trades are the second trap. A kitchen involves an electrician for the cooker circuit, the sockets and the under-cabinet lighting, a Gas Safe engineer for the hob, a plumber or the fitter for the sink and the appliances, a templater and fitter for stone worktops, and a tiler for the splashback. Carry them as named lines with a handling margin, not inside your own figure.
This guide builds the 2026 day rate, gives the regional figures and the fixed prices for the common kitchen sizes, lists the items that must stay as separate lines, and works a 12-unit kitchen through to a quote. For the whole-kitchen cost picture see full kitchen fit pricing guide and kitchen refurbishment pricing guide; for the method see pricing labour and day rate to hourly rate calculator.
Key Facts
- Day rate, 2026 — £230–£330 regionally; £280–£400 South East; £330–£480 London. Top of range for handleless and in-frame kitchens, bespoke joinery, solid timber worktops and fitters who manage all the trades
- Hourly equivalent — £35–£70, the day rate divided by 6.5–7 billable hours; use it for repairs and variations only
- Half-day minimum — £150–£220; a door realignment, a worktop re-seal or a single appliance swap
- Per-unit pricing — £50–£90 per base or wall unit fitted regionally, £70–£120 in London, as a sense check only; a kitchen is never priced on the unit count alone
- Standard kitchen, 10–14 units, laminate worktop, labour — £1,500–£3,000 regionally, 3–5 days; £2,500–£4,500 London
- Large kitchen, 15–25 units, island, laminate or timber worktop, labour — £3,000–£5,500 regionally, 5–8 days
- Rip-out — half a day to a day for an average kitchen including capping off, plus disposal at £200–£350 for a skip or three tip runs; a tiled floor under the units or a concrete plinth adds a half-day
- Laminate worktop — cut, jointed with a mason's mitre or a butt-and-scribe joint using a worktop jig, bolted and sealed: £40–£80 per joint plus the day rate; a 3-metre run with a hob and sink cut-out is 2–3 hours
- Stone, quartz and solid-surface worktops — templated and fitted by the supplier 7–14 days after the units are fixed; never price these as your own work. Units must be level within 3 mm over 3 m before the template. See quartz stone worktop fitting
- Solid timber worktop — oiled both sides before fitting, slotted fixings for movement, 2–3 hours per run plus two oiling visits; £150–£300 extra labour per kitchen
- Levelling — floors in older houses are commonly 10–25 mm out across a run; legs adjust 30–50 mm but the plinth and the worktop joint show every millimetre. Allow half a day for packing and scribing on a pre-1950 house
- Wall unit fixing — into masonry with 8 mm plugs and 70–80 mm screws or a hanging rail; into plasterboard with a batten or heavy-duty fixings rated for the loaded weight (a full 800 mm wall unit can exceed 40 kg). Dot-and-dab walls need the fixings to reach the masonry
- Electrics — the cooker circuit (32 A on 6 mm² minimum, up to 45 A on 10 mm² for a large range), sockets and under-cabinet lighting are Part P notifiable where a new circuit is added; sockets must be 300 mm from a hob and sink edge as good practice. Subcontract to a registered electrician at £250–£400 a day plus the certificate; see kitchen electrics
- Gas — hob connection, cooker bayonet and any gas pipe alteration is Gas Safe registered work; £100–£180 for a hob connection with a test, carried as a line
- Plumbing — sink, tap, dishwasher and washing machine in 2–3 hours if the services are within reach; moving the sink across the room is half a day with new 40 mm waste to BS EN 12056-2 at a 1:40 minimum fall. See kitchen plumbing
- Extraction — Approved Document F requires 30 l/s adjacent to the hob or 60 l/s elsewhere; a ducted hood through an outside wall with a 150 mm core drill is 2–3 hours and £150–£300 labour; see kitchen extraction ducting
- Tiling the splashback — 3–6 m² at £40–£70 per m² labour, usually a separate day after the worktops; a glass splashback is templated and fitted by the supplier
- Materials markup — 15–25% on fixings, silicone, worktop bolts, jointing compound, end panels cut from spare doors, plinth clips, cable and waste fittings; units and appliances usually customer-supplied through the showroom
- Billable days — 200–215 a year after holidays, surveys, quoting, snagging and the days lost to a damaged worktop or a missing unit
- Insurance — public liability £1–£2 million, £500–£900 a year; tools cover for the track saw, the jig and the laser
- Consumer Rights Act 2015, s.49 and s.51 — reasonable care and skill; reasonable price where none is agreed
- VAT — compulsory registration above £90,000; a fitter who supplies kitchens passes it quickly
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Charge | Regional (outside London/SE) | South East | London | Notes |
|---|---|---|---|---|
| Day rate, kitchen fitter, own tools | £230–£330 | £280–£400 | £330–£480 | 6.5–7 billable hours |
| Hourly equivalent | £35–£50 | £42–£60 | £50–£70 | Repairs and variations |
| Half-day minimum | £150–£220 | £180–£260 | £200–£300 | Door, hinge, reseal |
| Rip-out and disposal | £300–£600 | £350–£700 | £450–£900 | Skip extra on tight sites |
| Standard kitchen, 10–14 units, labour | £1,500–£3,000 | £2,000–£3,600 | £2,500–£4,500 | 3–5 days |
| Large kitchen, 15–25 units with island, labour | £3,000–£5,500 | £3,600–£6,500 | £4,500–£8,000 | 5–8 days |
| Laminate worktop joint, per joint | £40–£80 | £50–£90 | £60–£110 | Jig-cut, bolted, sealed |
| Sink, tap, dishwasher, washing machine connected | £150–£300 | £180–£350 | £220–£420 | Services within reach |
| Hob gas connection (Gas Safe) | £100–£180 | £120–£200 | £140–£240 | With tightness test |
| Electrician, cooker circuit, 6–8 sockets, lighting, certificate | £600–£1,100 | £700–£1,300 | £850–£1,600 | Part P notifiable |
| Extractor hood ducted through wall | £150–£300 | £180–£350 | £220–£420 | Core drill, 150 mm duct |
| Splashback tiling, per m² | £40–£70 | £45–£75 | £55–£90 | Labour only |
| Integrated appliance fitted, each | £40–£80 | £50–£90 | £60–£110 | Door, hinges, housing |
| Island installation, additional | £300–£600 | £350–£700 | £450–£900 | Plus services under floor |
Detailed Guidance
Building the day rate from your costs
The day rate is the year's costs plus the income you need, divided by the days you can actually bill:
| Annual cost | Typical figure |
|---|---|
| Van finance or depreciation, insurance, tax, fuel, servicing | £7,500–£10,500 |
| Tools: track saw, worktop jig, router, laser, mitre saw, consumables | £1,500–£3,000 |
| Public liability and tools insurance | £600–£1,100 |
| Phone, software, quoting app, accountancy | £1,200–£2,000 |
| Training, trade memberships | £200–£600 |
| Workwear, PPE | £250–£500 |
| Total overheads | £11,250–£17,700 |
With £45,000–£58,000 income over 205 billable days, the rate is £275–£370 before profit. That is why a regional kitchen fitter at £230 a day is at the floor and why showroom fitting rates of £180 a day only work for fitters with no van cost and a guaranteed diary.
Surveying before you price
Price from your own survey, never from the showroom plan alone. Measure the room at worktop height and at wall-unit height, check the corners with a 3-4-5 triangle or a laser square, run a laser line round the room at 870 mm and note the lowest and highest floor points, and locate every service: the stopcock, the gas pipe route, the consumer unit and the existing circuits, the soil pipe and the external drain. Check that the plan's sink sits over or within 1.5 m of the existing waste, that the hob is on an outside wall if the hood is to be ducted, and that the fridge housing clears the ceiling. A survey takes an hour and finds the half-day of levelling and the moved waste that the plan did not show.
Count the days from the survey:
| Stage | Typical days |
|---|---|
| Rip-out, cap off, dispose | 0.5–1 |
| Set out, level and fix base units, including corner units and housings | 1–1.5 |
| Wall units, cornice, pelmet, end panels | 0.5–1 |
| Laminate worktops: cut, joint, cut-outs, fix | 0.5–1 |
| Sink, tap, appliances, waste, supply | 0.5 |
| Doors, drawers, handles, plinths, adjustments | 0.5–1 |
| Snagging, silicone, clean | 0.25–0.5 |
| Total, 10–14 units | 3.75–6.5 |
The stone-worktop kitchen adds a return visit after the template and fit, usually a day for the sink, the hob cut-out services, the plinths and the final adjustment, which the fixed price has to include even though it is two weeks later.
Worktops: the line that decides the programme
Laminate is the fitter's own work: a worktop jig and a router for the mason's mitre, bolts underneath, a colour-matched sealant on the joint and the cut-outs sealed with a waterproof edging compound. Price it per joint plus the day rate time; a U-shaped kitchen with two joints and three cut-outs is most of a day. See worktop jointing methods.
Stone, quartz, sintered and solid-surface worktops are the supplier's work and arrive 7–14 days after the units are fixed and level. Price the first visit, the return visit and the gap in writing, and tell the customer the sink and hob cannot be used in between. The units must be within 3 mm of level over 3 m and the walls scribed before the template; a templater who finds the units out of level will leave and charge for the visit. Solid timber is the fitter's work but needs oiling on both faces before fitting, slotted brackets for seasonal movement, and two further oiling visits, so price it £150–£300 above laminate. See kitchen worktop fitting and kitchen worktop replacement pricing guide.
The trades you carry but do not do
Carry each as a named line on the quote with the subcontractor's price plus a 10–15% handling margin:
- Electrician: a cooker circuit, 6–10 sockets, under-cabinet lighting, an extractor spur and a dishwasher and washing machine supply, with the Electrical Installation Certificate and Part P notification. Appliances on a 32 A cooker circuit need a cooker control unit or an isolator; integrated appliances should have their socket in an adjacent cupboard, accessible without pulling the appliance. See kitchen appliance circuits
- Gas Safe engineer: the hob or range connection with a tightness test and the appliance commissioning; any pipe rerouting under the Gas Safety (Installation and Use) Regulations 1998. A gas hob over a built-under oven must follow the manufacturer's clearance table
- Plumber: optional if you are comfortable with the sink, the tap and the appliances; a relocated sink with a new waste to the external gully is a plumber's half-day
- Tiler: a splashback is a separate day after the worktop; the customer often arranges their own
- Plasterer or decorator: walls behind a ripped-out kitchen are rarely fit to tile or paint without a skim; carry a provisional sum of £300–£600 and state it
Fixing, levelling and the details customers check
Base units go on from the highest corner, levelled with the legs so the worktop sits at 900–920 mm, screwed to each other through the sides and to the wall at the top rail. Wall units hang on a hanging rail fixed to masonry with 8 mm plugs and 70–80 mm screws, or on heavy-duty plasterboard anchors only where a batten cannot be fitted; a dot-and-dab wall has a 20–25 mm void that the fixings have to bridge. Tall housings for ovens need a 5 mm clearance at the ceiling and the oven's own ventilation gaps per the manufacturer's sheet.
End panels, plinths and cornice are scribed to the wall and floor, not cut square and filled, and the gaps between doors should be 2–3 mm and even along the run. A customer who paid £15,000 for a handleless kitchen will check the drawer gaps with a credit card. Allow a half-day for the adjustments on a 14-unit kitchen and build it into the fixed price, not the snagging visit.
Worked example: 12-unit L-shaped kitchen, laminate worktop, Yorkshire
Rip out a 1990s kitchen, fit 7 base units including a corner carousel, 5 wall units, a tall oven housing, laminate worktops with one mason's mitre joint, a sink and hob cut-out, an integrated dishwasher, a ducted hood through the outside wall, and connect the sink, tap and dishwasher in the same positions. The showroom supplies the units and worktops; the customer supplies the appliances.
| Item | Days | Cost |
|---|---|---|
| Rip-out, cap off, three tip runs | 1 | £290 |
| Level and fix base units and tall housing (floor 18 mm out across the run) | 1.5 | £435 |
| Wall units, cornice, pelmet, end panels | 0.75 | £218 |
| Worktops: cut, one joint, two cut-outs, fix and seal | 0.75 | £218 |
| Sink, tap, dishwasher, waste and supply | 0.5 | £145 |
| Doors, drawers, handles, plinths, adjustment, silicone, clean | 0.75 | £218 |
| Hood ducted through wall, 150 mm core drill | 0.25 | £73 |
| Fixings, bolts, jointing compound, sealant, duct kit, waste fittings at trade + 20% | £185 | |
| Electrician: cooker circuit, 8 sockets, lighting, hood spur, certificate (£780 + 12%) | £874 | |
| Gas Safe: hob connection and test (£130 + 12%) | £146 | |
| Subtotal (5.5 days at £290 plus materials and subcontract) | £2,802 | |
| Provisional sum: skim two walls after rip-out | £420 | |
| Contingency 8% on fitter's labour | £128 | |
| Fixed price, excluding units, worktops, appliances and splashback tiling | £3,350 |
Quote at £3,350, with the provisional sum shown as such and the splashback tiling offered as an option at £320 for 5 m². Stage the payment: deposit on booking, 50% at the end of the units and worktops, the balance on completion with the electrical and gas certificates handed over. In London the same kitchen would be £4,600–£5,200.
Frequently Asked Questions
Should I price per unit or per day?
Per day, converted to a fixed price. A per-unit price treats a 300 mm base unit on a level floor the same as a corner carousel on a floor that drops 20 mm, and ignores the worktop, the services and the trades. Use a per-unit figure only to sanity-check the total (10–14 units at £50–£90 is £700–£1,250 for the carcass fitting alone, which is roughly a third of the fixed price) and to explain to a customer why a bigger kitchen costs more.
What if the units arrive damaged or the plan does not fit?
Check the delivery against the plan on the morning of day one, before the rip-out if you can, and photograph any damage. A missing or damaged unit is the supplier's problem, but the day you lose is yours unless the quote says what happens: a stated standing-time rate (the day rate) for a day lost to supply, and a return-visit charge for a unit delivered after you have left. Showrooms that fit through their own fitters have this in their terms; so should you.
Can I connect the gas hob myself?
No, unless you are Gas Safe registered for that work. A hob connection, including a bayonet fitting, is gas work under the Gas Safety (Installation and Use) Regulations 1998 and must be done and tested by a registered engineer. The same applies to moving the gas pipe. Carry the engineer's price as a line and schedule them for the afternoon the hob goes in.
How do I handle a customer-supplied kitchen from a flat-pack retailer?
Price the assembly as its own line: 20–40 minutes per flat-pack unit, so a 12-unit kitchen is an extra day. Rigid-carcass kitchens from a trade supplier arrive assembled and save that day. Make it clear that missing fittings, warped panels and the drawer runners that do not match the drawer are the retailer's responsibility and that time spent sorting them is at the day rate.
What should I charge for a worktop replacement only?
A laminate worktop replacement on an existing kitchen is 1–1.5 days: remove the old tops, disconnect and reconnect the sink and hob (Gas Safe for the hob), cut, joint and fit, reseal. Price at £350–£600 labour plus the worktop and a Gas Safe line, and survey first, because an old worktop often comes off with the tiles above it. See kitchen worktop replacement pricing guide.
Regulations & Standards
BS 7671:2018+A2:2022 — IET Wiring Regulations; cooker circuits, socket positions, RCD protection
Building Regulations 2010, Approved Document P — electrical safety; notifiable work in kitchens when a new circuit is added
Building Regulations 2010, Approved Document F — ventilation; 30 l/s extract adjacent to a hob, 60 l/s elsewhere
Gas Safety (Installation and Use) Regulations 1998 — all gas appliance connection and pipework by a Gas Safe registered engineer
Water Supply (Water Fittings) Regulations 1999 — WRAS-approved taps, check valves on appliance hoses
BS EN 12056-2:2000 — gravity drainage inside buildings; 40 mm sink waste at a 1:40 minimum fall
BS EN 14749:2016 — domestic and kitchen storage units; strength and durability requirements
BS EN 1116:2018 — coordinating sizes for kitchen furniture and appliances
Consumer Rights Act 2015 — reasonable care and skill; reasonable price
Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013 — 14-day cancellation right on contracts agreed in the customer's home
Control of Substances Hazardous to Health Regulations 2002 — MDF and laminate dust extraction when cutting
Approved Document P — GOV.UK — notifiable electrical work
Approved Document F — GOV.UK — kitchen extract rates
Gas Safe Register — who can work on gas — registration requirement for hob connections
Water Fittings Regulations — WRAS — approved fittings and backflow protection
Wood dust — HSE — MDF and laminate cutting controls
Self-employed expenses — GOV.UK — overhead items in the rate build-up
full kitchen fit pricing guide — the whole kitchen priced including units and trades
kitchen refurbishment pricing guide — refurbishment versus replacement
kitchen worktop replacement pricing guide — worktop-only jobs
kitchen units installation — fixing and levelling detail
kitchen electrics — circuits and socket positions
day rate to hourly rate calculator — converting rates
pricing labour — the method across trades