Summary
A tap change is the smallest plumbing job a customer will ring about and the one most often priced wrongly in both directions: too cheap by the plumber who quotes thirty minutes for a job that turns into two hours under a kitchen sink with seized back nuts, corroded tap tails and no isolation valves, and too dear by the one who quotes a day because it is a bathroom. The right figure comes from a short list of questions asked before the visit: what tap, what it is going onto, what the hot supply is, whether there are isolation valves, and how old the pipework is.
The job also carries regulation that a customer does not see. The Water Supply (Water Fittings) Regulations 1999 require every fitting to be of an appropriate quality and standard (regulation 4), which for taps means a product approved by WRAS or carrying equivalent third-party certification, and require backflow protection where supplies at different pressures or qualities can mix, which is what a mixer tap does. The tap also has to work with the hot water system: a tap designed for 1 bar mains on a gravity cylinder with 0.2 bar at the kitchen gives a dribble, and the customer will ring back. This guide gives the 2026 labour and materials build-up by tap type and location, the questions that set the price, the regulatory points to price in, a worked example, and the small-job pricing that keeps a tap change profitable. For the related jobs see tap dripping or spluttering, dripping tap, isolation valves and boiling water tap installation.
Key Facts
- Labour, kitchen monobloc, like for like — 1–1.5 hours: £80–£150 regionally, £100–£180 South East, £120–£220 London, including fitting new flexible connectors and isolation valves if there are none
- Labour, basin monobloc or pillar taps — 1–1.5 hours: £80–£150 regionally; a pedestal basin with the tails behind the pedestal is at the top of the band
- Labour, bath taps or bath shower mixer — 1.5–2.5 hours: £100–£180 regionally, £140–£250 London; the bath panel comes off, the access is through a 400 mm gap, and the tails are ¾ in BSP with 22 mm connectors
- Labour, wall-mounted or deck-mounted with concealed body — 2–4 hours and often tiling to make good; price as a half-day minimum plus making good
- Half-day minimum — £60–£120 for a single tap where nothing else is being done; it is travel, isolation, the job, the test and the clean-up
- Hourly rate basis — £45–£70/hour regionally for a plumber in 2026; see plumber hourly rate guide
- Tap costs, trade — basic monobloc mixer £35–£80; mid-range chrome mixer £80–£200; quality brassware £200–£500+; pair of pillar taps £30–£100; bath shower mixer £80–£300; pull-out spray kitchen mixer £120–£400; boiling-water tap £500–£1,500 plus the tank and filter (a different job)
- Materials beyond the tap — flexible tap connectors (WRAS-approved, braided, 300–500 mm, ½ in or ¾ in BSP) £4–£10 each; isolation valves 15 mm £3–£6 each (full-bore or lever for flow); tap connectors (straight or bent, ½ in × 15 mm, ¾ in × 22 mm) £3–£8; PTFE, jointing compound, fibre washers £2–£5; basin/bath tap backnuts and top-hat washers £2–£6; a tap hole blanking plate or sink cover for a two-hole sink going to a monobloc £8–£20
- Pressure matching — a gravity-fed hot supply from a cylinder in an airing cupboard gives 0.1–0.3 bar at a first-floor basin and 0.3–0.5 bar at a kitchen; a combi or unvented system gives 1–3 bar. Taps are rated by minimum operating pressure (0.1, 0.2, 0.5, 1.0 bar); a high-pressure tap on a gravity hot supply is the commonest "new tap, no flow" complaint
- Mixer taps and backflow — where a single-lever or single-outlet mixer is fed by mains cold and stored (cylinder) hot, the two supplies can cross-flow; the Water Fittings Regulations require backflow prevention, in practice a single check valve on each supply or a mixer with check valves built in; a twin-flow (biflow) mixer with separate waterways does not mix and does not need them
- Hot water temperature — a domestic tap has no TMV requirement, but a thermostatic mixing valve to BS EN 1111 (TMV2) is good practice on a bath in a household with young children or elderly users, and is required in care settings; price it as an option at £60–£120 plus 45 minutes
- Lead pipe — a pre-1970 property with lead supply to the kitchen tap: the replacement tap goes on, but the lead pipe should be reported and a replacement to the stopcock quoted; see stopcock replacement pricing guide
- Water Regulations notification — a tap change is not notifiable; a new installation of certain fittings (a bidet with an ascending spray, a bath over 230 litres, a pumped shower over 12 l/min) is
- Part P and electrics — not applicable to taps, except an instantaneous electric water heater at the tap (a new circuit is notifiable)
- Materials markup — 15–25% on taps you supply, plus the delivery and the returns risk; 20–30% on the sundries
- Customer-supplied taps — state on the quote that the fitting is to the manufacturer's instructions, that the tap must be WRAS-approved or equivalent and suitable for the system pressure, and that a tap that arrives with the wrong tails, missing parts or damaged is charged at the hourly rate for the wasted visit
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Regional (outside London/SE) | South East | London | Time | Notes |
|---|---|---|---|---|---|
| Kitchen monobloc mixer, like for like | £80–£150 | £100–£170 | £120–£220 | 1–1.5 hr | Plus tap; incl. flexis and isolation valves |
| Kitchen monobloc replacing two pillar taps (two-hole sink) | £100–£180 | £120–£200 | £150–£250 | 1.5–2 hr | Cover plate or new sink; mixer backflow check |
| Basin monobloc, like for like | £80–£150 | £100–£170 | £120–£220 | 1–1.5 hr | Pedestal basins at top of band |
| Basin pillar taps, pair | £80–£140 | £95–£160 | £120–£200 | 1–1.5 hr | |
| Bath taps, pair, or bath filler | £100–£180 | £120–£210 | £140–£250 | 1.5–2.5 hr | Panel off; ¾ in tails |
| Bath shower mixer, like for like | £110–£190 | £130–£220 | £150–£270 | 1.5–2.5 hr | Hose, riser rail extra if replaced |
| Wall-mounted or concealed-body tap | £180–£350 | £220–£400 | £260–£480 | 3–5 hr | Plus tiling / making good |
| Add isolation valves only (pair) | £40–£70 | £50–£80 | £60–£100 | 30–45 min | 15 mm, WRAS |
| Fit check valves to a mixer (pair) | £40–£70 | £50–£80 | £60–£100 | 30–45 min | Backflow compliance |
| Fit TMV2 under a bath or basin | £120–£200 | £140–£230 | £170–£280 | 1–1.5 hr | Plus valve £60–£120 |
| Outside tap (new installation) | see outdoor tap installation pricing guide | Double check valve mandatory | |||
| Half-day minimum for a single tap | £60–£120 | £70–£140 | £90–£170 |
Detailed Guidance
The five questions that set the price
- What tap, and what is it going onto? Monobloc into one hole, pillar taps into two, bath filler, bath shower mixer, wall-mounted. A monobloc going onto a two-hole sink needs a cover plate (and a sink that will take it) or a new sink. A customer's "new tap" bought online may have the wrong tails (10 mm or 3/8 in flexis on a European tap, M10 studs), which is an adaptor and a return visit if you did not ask
- What is the hot water? Combi or unvented: high pressure, any tap works. Cylinder in the airing cupboard with a cold tank in the loft: gravity, low pressure, and the tap must be rated for it (0.2 bar or lower for a first-floor basin). Ask what the boiler is or where the hot tank is; the answer decides whether the tap the customer wants will actually work
- Are there isolation valves? If not, you are turning the house off at the stopcock (which may be seized — see stopcock types), draining down to the tap, and fitting isolation valves while you are there. That is 30–45 minutes and £10 of valves, and it belongs on the quote
- How old is the pipework, and what is the access? A 1970s kitchen with 15 mm copper on compression fittings behind a 600 mm base unit is one job; a 1930s kitchen with a lead supply, a seized BS 1010 stopcock and the pipework chased into the wall is another. A bath with the panel sealed in with silicone and tiled over is a two-hour job before the taps are touched
- Who supplies the tap? You supply: markup, delivery, a tap you know fits. Customer supplies: no markup, a stated assumption that it is suitable and complete, and the hourly rate if it is not
A two-minute phone call with those five questions prices nine tap jobs out of ten correctly. The tenth gets a survey visit.
Labour build-up: kitchen monobloc
The time on a standard replacement, where the hot and cold are 15 mm copper with isolation valves:
| Step | Time |
|---|---|
| Isolate at the valves, open the tap to drop pressure, sheet the cupboard | 5 min |
| Disconnect flexis at the valves, undo the backnut or stud fixing under the sink (basin wrench or box spanner), lift the old tap | 10–20 min |
| Clean the sink hole, fit the new tap with its seal, tighten from below | 10–15 min |
| Fit new flexis to the tap tails (never reuse old flexis), connect to the isolation valves | 10 min |
| Open valves, check for leaks, run both hot and cold, check the aerator | 5–10 min |
| Clean up, demonstrate, invoice | 5 min |
| Total | 45–65 min |
Add 20–30 minutes if there are no isolation valves (house off at the stopcock, drain, fit valves), 20–40 minutes if the old backnuts are seized and have to be cut, and 15–20 minutes if the tap tails are a different size from the existing flexis. That spread is why the band is 1–1.5 hours and the price £80–£150, not "half an hour, £40".
Labour build-up: bath taps
Bath taps are the same job with three complications: the panel (clipped, screwed, or siliconed and tiled), the access (lying under the bath reaching up to ¾ in backnuts with a bath tap spanner), and the tails (22 mm or ¾ in flexis, often rigid copper on an older installation that needs cutting and new connectors). A bath shower mixer adds the hose, the handset and the riser rail if they are being replaced, and the check that the mixer is suitable for the pressure (a bath shower mixer on gravity hot needs a low-pressure model or the shower side will not work). Allow 1.5–2.5 hours and price £100–£180 regionally; if the panel has to be cut out and replaced, that is a separate line at £40–£80 plus the panel.
Regulatory points to price in
- Fitting quality (Water Fittings Regulations, regulation 4) — the tap and every connector must be of an appropriate quality and standard. WRAS approval, or certification by another UKAS-accredited body against the Regulations, is the usual evidence. A customer's unbranded import with no approval is a risk; say so in writing and fit it at their instruction, or decline
- Backflow (Schedule 2, paragraph 15) — a mixer tap where mains cold and stored hot share a waterway creates a fluid category 2 risk (stored water into the mains); fit a single check valve on each supply or a mixer with integral check valves. Many monoblocs for the UK market have them built in; the data sheet says. Outside taps and taps with hose connections need a double check valve (fluid category 3); see backflow prevention check valves
- Servicing valves (Schedule 2, paragraph 10) — a servicing valve is required on the supply to every float-operated valve and every appliance; for taps it is good practice and the thing that makes the next tap change a 45-minute job. Fit them
- Materials in contact with water — no lead solder on potable water (use lead-free to BS EN ISO 9453); dezincification-resistant (DZR) brass fittings where the water is aggressive
- Water efficiency — not retrospective for a replacement, but Approved Document G2 limits new dwellings to 125 litres per person per day, and an aerated tap at 5–6 l/min is a reasonable recommendation on any kitchen or basin tap
- Scalding — no TMV requirement for a domestic tap, but offer a TMV2 to BS EN 1111 on a bath where there are young children, elderly or disabled users; mandatory in care homes and recommended in Approved Document G3 for baths in new dwellings (48 °C maximum at the bath outlet in new dwellings)
Worked example: kitchen tap, no isolation valves, 1960s semi
Customer-supplied chrome monobloc mixer (checked by phone: WRAS-approved, ½ in flexis, suitable for 0.5 bar minimum; hot is from a combi, so fine). Existing: pair of pillar taps on a two-hole stainless sink, 15 mm copper, no isolation valves, stopcock under the sink works.
Labour: 1.75 hr @ £60 = £105
(isolate at stopcock, drain, remove pillar taps, fit
monobloc with cover plate, fit 2 isolation valves,
new flexis, test)
Materials
2 × 15 mm full-bore isolation valves £10
2 × flexi tap connectors ½ in × 15 mm £12
Stainless cover plate £14
PTFE, washers, compound £3
£39 + 25% = £49
------
Invoice £154
Tap: customer-supplied (not warranted by us)
A quote of £120 "to fit a tap" on this job would have been a loss once the isolation valves and the cover plate were found on the day. Asking the questions put them on the quote.
Small-job pricing that keeps it profitable
A single tap change is a classic small job: an hour on site, an hour of travel and admin around it. Pricing it at the hourly rate alone loses money. The options that work:
- Fixed price per tap type from the table, with the sundries included and a stated list of what is not (seized stopcock, new sink, lead pipe, making good)
- Half-day minimum with the tap change and anything else the customer can find in the same visit (a dripping tap elsewhere, a slow basin waste, an outside tap isolation valve) — the customer gets value, you get a billable half-day
- Call-out plus hourly for emergency or same-day work: £80–£150 for the first hour, then the hourly rate
See handyman hourly rate pricing guide and emergency callout pricing guide for the structures; pricing labour for the cost basis.
What to put in writing
The tap by make and model (or "customer-supplied, assumed WRAS-approved and suitable for [system]"), the location, whether isolation valves and flexis are included, the backflow provision if it is a mixer on mixed supplies, the half-day minimum, the hourly rate for anything found on the day, and a 12-month workmanship guarantee that excludes the tap if the customer supplied it. Under the Consumer Rights Act 2015 you owe reasonable care and skill; a tap that fails because it was unsuitable for the pressure and you did not say so is on you.
Frequently Asked Questions
How much does a plumber charge to fit a tap?
In 2026, £80–£150 labour outside London for a kitchen or basin mixer, £100–£180 for bath taps, and 25–40% more in London, plus the tap. If there are no isolation valves, add £40–£70 to fit them while the water is off. Most plumbers put a half-day minimum (£60–£120) under a single tap, so it is worth having two or three small jobs done in one visit.
Can any tap go on any system?
No. Taps are rated for a minimum working pressure. A gravity hot water system (cylinder and loft tank) gives 0.1–0.5 bar at the taps, and a tap rated for 0.5 or 1 bar will dribble on the hot side. Combi and unvented systems give 1 bar or more and take any tap. Check the system before buying; a low-pressure (0.1–0.2 bar) tap works on everything.
Does a mixer tap need check valves?
If it is a single-lever or single-waterway mixer fed by mains cold and stored (cylinder) hot, yes: the Water Supply (Water Fittings) Regulations 1999 require backflow prevention where the two can mix, usually a single check valve on each supply. Many UK-market mixers have them built in; the data sheet will say. A twin-waterway (biflow) mixer keeps the supplies separate until the spout and does not need them. An outside tap always needs a double check valve.
Should I fit isolation valves when changing a tap?
Yes, if there are none. They cost £3–£6 each, take 15 minutes while the water is already off, and turn the next tap change or washer into a 30-minute job without turning the house off. The Water Fittings Regulations require servicing valves on supplies to float valves and appliances; on taps they are good practice, and a customer who has just paid to have the whole house drained for a tap will see the point.
Why does a new tap sometimes have low flow?
Three reasons: the tap is rated for a higher pressure than the system provides (gravity hot); the aerator or flow restrictor in the spout is partly blocked with debris from the pipework disturbed during the change (unscrew and rinse); or the isolation valves were not fully reopened. Check all three before condemning the tap.
Regulations & Standards
Water Supply (Water Fittings) Regulations 1999 (SI 1999/1148) — regulation 4 (fitting quality), Schedule 2 paragraph 10 (stop and servicing valves), paragraph 15 (backflow prevention and fluid categories)
Water Byelaws 2004 (Scotland) and the equivalent Northern Ireland regulations — the same requirements outside England and Wales
Building Regulations 2010, Approved Document G (2015 edition with 2016 amendments) — G2 water efficiency (125 l/person/day in new dwellings), G3 hot water supply and scalding (48 °C bath outlet in new dwellings)
BS EN 200:2008 — sanitary tapware; single taps and combination taps for water supply systems of type 1 and type 2; general technical specification
BS EN 817:2024 — sanitary tapware; mechanical mixing valves (PN 10); general technical specifications
BS EN 1111:2017 — sanitary tapware; thermostatic mixing valves (TMV2 scheme basis)
BS EN 1112:2008 and BS EN 1113:2015 — shower outlets and shower hoses for sanitary tapware
BS EN 13618:2016 — flexible hose assemblies in drinking water installations
BS EN 1254 series — copper and copper alloy plumbing fittings (compression and capillary tap connectors)
BS EN ISO 9453:2020 — soft solder alloys; lead-free solder for potable water
BS EN 806-2:2005 — specifications for installations inside buildings conveying water for human consumption; design
BS 8558:2015 — guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages
Consumer Rights Act 2015 (s.49–s.52) — reasonable care and skill; reasonable price where none agreed
Water Supply (Water Fittings) Regulations 1999 — the statutory text including Schedule 2
WRAS — Water Regulations Advisory Scheme: approved products and guidance — product approvals and backflow guidance
Water Regs UK — Information for installers — notification requirements and installer guidance
HM Government — Approved Document G: Sanitation, hot water safety and water efficiency — G2 and G3
CIPHE — Chartered Institute of Plumbing and Heating Engineering: technical guidance — good practice for domestic installations
BSI — BS 8558:2015 domestic water services — design and installation guide
tap dripping or spluttering — when a repair (cartridge, washer, aerator) is the better sell than a replacement
dripping tap — washer and ceramic-disc repair method
isolation valves — valve types, where they are required and where they should be fitted
backflow prevention check valves — fluid categories and check valve selection for mixers and hose taps
stopcock types — the stopcock you will need to turn when there are no isolation valves
stopcock replacement pricing guide — pricing the seized stopcock found on the day
outdoor tap installation pricing guide — outside tap installation with double check valve
boiling water tap installation — the boiling-water tap, a different job with a tank and a filter
plumber hourly rate guide — the hourly rate the labour figures are built from
handyman hourly rate pricing guide — small-job pricing structures