Summary
Wall panelling has gone from heritage joinery to one of the most requested interior jobs in the country, driven by home-improvement television and social media. For the carpenter or decorator it is attractive work: indoors, clean, quick, high perceived value, and easy to photograph for the next customer. It is also easy to under-price, because the materials look cheap (a few lengths of MDF strip and a tube of grab adhesive) and the customer has usually seen a "£80 DIY panelled wall" video. What that video does not show is the two hours of setting out, the scribing to an out-of-plumb wall, the caulking, the filling of every joint, the priming of raw MDF edges, and the two coats of eggshell that make the difference between a feature wall and a mess.
Price panelling per square metre of wall covered, with the price band set by the style (shaker, board-and-batten, tongue-and-groove, slatted, full-frame) and the finish included. Separate the carpentry from the decoration in your build-up even if you present one price, because the decoration is often 35–45% of the labour on a painted MDF scheme. Then check the figure against a day rate: a carpenter should be making £220–£320 a day on panelling, and a decorator £180–£260, and if the per-metre price does not get there on a realistic output, it is wrong.
This guide gives 2026 price bands by style, the material costs and waste allowances, realistic outputs per day, the extras that catch people out (sockets and switches, radiators, stairs, uneven walls, old lining paper), and a worked example. For the installation method see wood panelling installation and dado rail installation; for the decoration side see caulking before painting and painter decorator day rate guide.
Key Facts
- Price per m² (2026, supplied, fitted, painted, regional) — shaker / board-and-batten to dado height £60–£100; shaker full height £70–£110; tongue-and-groove (MDF or softwood) £90–£150; full-frame Jacobean / Georgian raised panels £130–£220; slatted acoustic panels (felt-backed) £110–£200; London and South East add 20–30%
- Carpentry output — one carpenter fits 8–14 m² of shaker panelling a day on a straight, plumb wall, 5–8 m² on a stair or a wall with multiple sockets and a radiator; tongue-and-groove 6–10 m² a day; slatted panels 10–15 m² a day
- Decorating output — fill, sand, caulk, prime and two coats of eggshell or satinwood: 12–20 m² a day across two or three visits (drying time between coats)
- Material: MDF strips — primed 9 mm MDF strip at 68 mm or 94 mm wide, 2.44 m lengths, £3–£6 per length; 12 mm or 18 mm for a deeper profile £5–£9; moisture-resistant (MR, green-tinted core) 20–40% more
- Material: MDF sheets — 2,440 × 1,220 mm 9 mm standard £22–£32, MR £30–£42; a sheet rips into eleven 94 mm strips or sixteen 68 mm strips (minus blade kerf), so sheet-ripping halves strip cost where a table saw is on site
- Material: tongue-and-groove — MDF T&G 9 mm × 120–150 mm £4–£7 per 2.4 m length; redwood softwood T&G £5–£9 per 2.4 m; needs a top rail and skirting
- Material: slatted acoustic panels — 2,400 × 600 mm felt-backed panels with 27–30 mm oak-veneer or MDF slats, £60–£130 per panel (£42–£90/m²) retail, less trade
- Fixings and consumables per 10 m² — grab adhesive 2–3 cartridges (£5–£9 each), 18-gauge brad nails or 25 mm pins, decorators' caulk 2–3 tubes, filler, 120/180-grit abrasive, MDF primer or quick-dry primer-undercoat 1 litre, eggshell or satinwood 1.5–2.5 litres for two coats: £45–£90
- Waste — allow 10–15% on strips and T&G, 15–20% on stairs and angled work
- Moisture-resistant MDF — use MR grade (BS EN 622-5, type MDF.H) in bathrooms, kitchens, utility rooms, on external walls and anywhere condensation is likely; standard MDF swells irrecoverably when wet
- Fire — in a dwelling, wall linings in habitable rooms have no reaction-to-fire requirement under Approved Document B Volume 1, but linings in a protected stairway or circulation space of a flat or HMO must meet Class C-s3,d2 (formerly Class 1) or better: unfinished MDF and softwood do not, so stair panelling in flats and HMOs needs an intumescent or Class 1 paint system or FR-grade board
- Electrics — sockets and switches in the panelled zone need either extending forward with box extenders or re-setting; this is minor electrical work but adding a socket is new work under BS 7671:2018+A2:2022 and may need a Minor Works Certificate; never bury a live accessory behind panelling
- Radiators — remove and refit (£60–£120 by a plumber or competent carpenter, with drain-down or isolation) or panel around with a scribed infill; price explicitly
- Dado height — traditionally 900–1,000 mm to the top of the rail; stair dado follows the string at the same height off each tread nosing
- Setting out — equal panel widths with a consistent margin (typically 50–100 mm stiles, 50–150 mm margins) are what the customer judges; allow 1–2 hours per room for setting out and a drawn layout before cutting
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Panelling style | Materials per m² | Carpenter hours per m² | Decorator hours per m² | Supplied, fitted, painted (regional) | London / SE |
|---|---|---|---|---|---|
| Shaker / board-and-batten, dado height, MDF strip | £12–£20 | 0.6–0.9 | 0.4–0.6 | £60–£100 | £75–£130 |
| Shaker full height, MDF strip | £14–£22 | 0.6–0.9 | 0.4–0.6 | £70–£110 | £85–£140 |
| Board-and-batten with sheet backing (over poor plaster) | £22–£32 | 0.8–1.1 | 0.4–0.6 | £85–£130 | £105–£165 |
| Tongue-and-groove MDF, dado height with cap | £18–£28 | 0.9–1.3 | 0.5–0.7 | £90–£140 | £110–£175 |
| Tongue-and-groove softwood, full height | £24–£38 | 1.0–1.4 | 0.6–0.8 | £110–£160 | £135–£200 |
| Full-frame raised and fielded (MDF) | £35–£60 | 1.5–2.5 | 0.6–0.9 | £130–£220 | £165–£280 |
| Slatted acoustic panel (felt-backed, veneered), no painting | £45–£95 | 0.4–0.7 | 0 | £110–£200 | £135–£250 |
| Stair dado (per m² of string run) | +25% | +40–60% | +30% | £95–£160 | £120–£200 |
| Radiator remove and refit | — | — | — | £60–£120 | £80–£150 |
| Socket / switch extension forward (each) | £4–£12 | 0.25–0.5 | — | £20–£45 | £25–£55 |
Detailed Guidance
Measure what you will actually cover
Measure the wall area to be panelled, not the room. For a dado scheme that is the wall length × dado height (0.9–1.0 m); for full height, wall length × ceiling height less any openings you are framing around. Then list the obstacles: sockets, switches, radiators, windows, doors, a stair string, a boxed-in pipe, an alcove. Each costs time out of proportion to its area, so either price them as extras or add 20–40% to the labour on a wall with several.
Check the wall itself. Panelling will not hide a wall that is bowed or out of plumb; it will emphasise it, because the eye reads the straight rails against the wall. Old lining paper or blown plaster must come off or be fixed first (grab adhesive to wallpaper fails). An out-of-plumb wall needs either a sheet backing to form a flat plane (the board-and-batten-on-sheet method) or the strips packed and scribed, both of which take time. Record it on the quotation.
Materials build-up
For MDF strip panelling, the quantity method is simple: draw the layout, count the rails and stiles, add the lengths, add 10–15% waste, convert to 2.44 m lengths. For a 4 m × 1 m dado shaker wall with 5 panels: two horizontal rails of 4 m (8 m), six stiles of about 0.8 m (4.8 m), a top capping rail 4 m (bullnose or torus, £4–£8 per length), total 16.8 m plus 12% = 18.8 m, so 8 lengths of 94 mm strip (£32–£48) plus 2 lengths of capping (£10–£16). Adhesive, pins, caulk, filler and primer for 4 m² around £25–£40, paint £15–£25. Materials for that wall: £80–£130, on a fitted-and-finished price of £300–£450.
Decide standard or moisture-resistant MDF by room. The cost difference is a few pounds a length; the cost of standard MDF swelling at skirting level in a bathroom is a full strip-out. Where the panelling is in a kitchen behind a hob or sink, in a bathroom, or on a cold external wall of an older house, specify MR and say so on the quote.
Carpentry labour
Realistic outputs per carpenter-day for shaker panelling are 8–14 m² on a straight wall and 5–8 m² where there are sockets, a radiator or a stair. Setting out is the time most under-estimated: an hour or two per room to work out panel widths that come out equal around the obstacles, mark the datum line with a laser, and dry-lay the first rail. The fixing itself is quick: grab adhesive plus pins into the plaster, or screws into battens where the plaster is poor.
Tongue-and-groove is slower because every board is fixed individually and the ends are scribed to skirting and ceiling or trimmed with a cap. Full-frame raised panels are joinery, not site work: the frames are usually made up in the workshop and the price reflects it.
Slatted acoustic panels are fast to fix (screwed or glued through the felt) but unforgiving: the slats must be plumb, the panel joints must meet without a visible line, and cuts around sockets show. Allow time for trimming the slats individually at the ends and for an edge trim or shadow gap detail.
Decorating labour
Painted MDF panelling needs: all joints and pin holes filled and sanded, every junction with the wall and between strips caulked, raw cut edges sealed (MDF edges drink paint), a primer or primer-undercoat coat if the strip is not pre-primed or where edges are cut, and two coats of a durable finish, usually water-based eggshell or satinwood. The wall infill panels are painted either in the same colour (the common modern look) or in emulsion in a contrasting shade. That is three to four visits with drying time, and a decorator will cover 12–20 m² per day of effort spread across them. On a dado shaker wall the decorating is 35–45% of the labour, and on a full-height scheme it can be half. If the customer wants to paint it themselves, price the carpentry only and say that filling, caulking and priming are excluded.
Fire, electrics and the rules that apply
Panelling is decorative and non-structural: no Building Regulations application is needed in a house. Two exceptions matter. In the common parts of a block of flats, or a protected stairway in an HMO or a flat with an internal protected route, wall linings must achieve at least Class C-s3,d2 to BS EN 13501-1 (Class 1 to BS 476-7 under the old system) under Approved Document B Volume 1 and Volume 2; raw softwood and standard MDF do not, so use a Class 1 intumescent paint system or flame-retardant MDF and keep the certificates. Landlords of HMOs will ask.
Electrics: any socket, switch or data outlet in the panelled zone must be brought forward to the new face using a surface box or box extender so that the accessory remains accessible and the cable terminations are inside an enclosure. Never pack panelling over a flush accessory or cut strips to leave it recessed behind the face. Fixing pins and screws into walls must respect the cable safe zones in BS 7671 Regulation 522.6 (within 150 mm of the top of the wall or a corner, or in line with an accessory): assume a cable runs vertically and horizontally from every accessory and use a cable detector before fixing. If panelling conceals a cable route completely, that cable should already be in a safe zone or RCD-protected; adding panelling does not change its status but does make the next person's job harder, so photograph the wall before you cover it.
Worked example: hallway and stairs, shaker dado
Hall 3.6 m + 2.2 m walls, stair string 4.2 m, landing 2.8 m; dado height 1.0 m; 5 panels per wall section; one radiator to remove and refit; two light switches to extend forward; existing plaster sound, lining paper to strip (1 hour).
| Element | Quantity | Rate | Total (ex VAT) |
|---|---|---|---|
| Panelled area | 12.8 m² (hall and landing) + 4.2 m² stair = 17.0 m² | ||
| MDF strip 94 mm primed, 2.44 m, incl. 15% waste (stair 20%) | 34 lengths | £4.20 | £143 |
| Capping rail, bullnose MDF | 6 lengths | £6.50 | £39 |
| Adhesive, pins, caulk, filler, abrasive | £48 | ||
| Primer-undercoat 2.5 l, eggshell 5 l | £92 | ||
| Carpenter: strip paper, set out, fit hall and landing | 1.5 days | £280 | £420 |
| Carpenter: stair dado (scribed to string, raked top rail) | 1 day | £280 | £280 |
| Radiator remove and refit, isolation and bleed | 1 | £90 | £90 |
| Switch extension forward × 2 | 2 | £30 | £60 |
| Decorator: fill, caulk, prime, two coats; infills in same colour | 2 days over 3 visits | £220 | £440 |
| Cost | £1,612 | ||
| Margin 20% | £322 | ||
| Price | £1,934 → quote £1,950 ex VAT (£115/m²) |
The per-metre figure lands above the straight-wall shaker band because 25% of the area is a stair with a raked rail and the scheme includes stripping, a radiator and switch work. Presented to the customer as "hall, stairs and landing panelled and painted, £1,950", with the extras itemised so that a later "can you do the bedroom too" starts from £70–£90/m².
Terms and exclusions
- State the style, strip width, panel count per wall and the height; attach the drawn layout once agreed
- State the finish: "filled, caulked, primed and two coats of water-based eggshell in colour X" or "carpentry only, supplied in primed MDF ready for decoration"
- Exclude or price: removal of lining paper or blown plaster, radiators, electrical accessories, making good to ceilings and skirtings, moving furniture, disposal
- Specify MR MDF where used and the reason
- For flats and HMOs, state the fire class of the finish system and that certificates will be supplied
Frequently Asked Questions
Should I price panelling per m², per linear metre, or per wall?
Per m² for your own build-up, because labour and materials both scale with area and it lets you compare jobs. Present the customer with a price per wall or per room, built from the m² rate plus the itemised extras (radiator, sockets, stairs). Quoting a bare m² rate to a homeowner invites them to measure the room area instead of the panelled area and dispute the total.
Do I need Building Regulations approval to fit wall panelling?
Not in a house; it is a decorative lining. In the common parts of flats, a protected stairway in an HMO, or a licensed HMO generally, the lining must meet the fire-class requirements of Approved Document B (Class C-s3,d2 / Class 1 or better) and the local authority or fire risk assessor will want evidence. Use an intumescent paint system or flame-retardant board and keep the data sheets.
Standard or moisture-resistant MDF?
Moisture-resistant in any bathroom, kitchen, utility, downstairs WC, on external walls in older solid-wall houses, and anywhere the customer has had condensation. Standard MDF everywhere else is fine. The price difference is 20–40% on the board, which is a few pounds a length; the cost of standard MDF swelling is the whole wall again.
How do I deal with sockets in a panelled wall?
Bring them forward to the new face with a surface pattress or a box extender so the accessory sits flush on the panelling and the terminations remain inside an enclosure. If the socket falls awkwardly across a stile, move the stile (that is what the setting-out hour is for) rather than cutting the strip around the socket. Moving or adding sockets is electrical work under BS 7671 and should be done by someone competent to test and certify it.
Can the panelling be painted the same day it is fitted?
Only if nothing needed filling or caulking, which never happens. Filler and caulk need to cure before sanding and priming, and each paint coat needs its recoat time (typically 4–6 hours for water-based eggshell, longer in a cold room). Realistically the decorating is three visits over three or four days after the carpentry; build that into the programme and the price.
Regulations & Standards
Building Regulations 2010, Approved Document B Volume 1 (Dwellings) and Volume 2 (Buildings other than dwellinghouses) — internal fire spread (linings), Requirement B2: wall and ceiling lining classes for circulation spaces, protected stairways and common parts
BS EN 13501-1:2018 — fire classification of construction products: reaction to fire (Classes A1–F, s and d ratings) used for lining classes
BS 476-7:1997 — surface spread of flame test; the former Class 1 lining rating still referenced for existing products
BS EN 622-5:2009 — Fibreboards: requirements for dry process boards (MDF), including moisture-resistant grades
BS 7671:2018+A2:2022 — Requirements for Electrical Installations: Regulation 522.6 (cables concealed in walls, safe zones) and enclosure requirements for accessories brought forward
BS 6150:2019 — Code of practice for painting of buildings: preparation and coating of MDF and timber
BS 1186-3:1990 — Timber for and workmanship in joinery: wood trim and its fixing
Housing Act 2004 (HMO licensing) and Regulatory Reform (Fire Safety) Order 2005 — fire safety in HMOs and common parts where linings are changed
Consumer Rights Act 2015 — work to be carried out with reasonable care and skill, materials of satisfactory quality
Approved Document B: Fire safety, Volume 1 Dwellings — GOV.UK — lining classes for circulation spaces and protected stairways
Wood Panel Industries Federation: MDF guidance — MDF grades, moisture resistance and working
TRADA / BM TRADA timber guidance — timber and panel product specification
BS 7671 IET Wiring Regulations — IET — concealed cable zones and accessory enclosures
HSE: Wood dust — controlling the risks — MDF dust control when cutting on site
wood panelling installation — the fitting method step by step
dado rail installation — setting out and fixing dado rails and cappings
caulking before painting — the caulking and filling that makes painted panelling look right
painter decorator day rate guide — decorator day rates behind the finishing labour
skirting board fitting pricing guide — skirting and trim pricing for the same rooms
mdf vs plywood comparison — board selection for backing and panels
carpenter day rate guide — carpenter day rates behind the fitting labour