Summary

A stud wall is one of the most-quoted small building jobs, and one of the easiest to under-price, because the framing looks quick and the customer has usually seen a price online that stops at the timber and the boards. The real job is framing, boarding both sides, a door opening with a lining, the plaster skim, the skirting and architrave both sides, the socket or switch that always ends up in it, and a day of making good where the new wall meets an out-of-true ceiling and floor. A carpenter who quotes £400 for "a stud wall" and then does all of that has worked for a day rate of about £100.

The specification question comes before the price. A partition between a bedroom and a landing in a loft conversion has to meet Approved Document E for sound (40 dB Rw minimum as built); one between a new en-suite and the bedroom needs moisture-resistant board on the wet side; one that supports a wall-hung basin or a TV needs noggins and pattresses in the right places; one on a floor that spans the wrong way needs the joist direction checked before the sole plate goes down. Each of those is a different wall at a different price, and the quote should say which one it is. This guide gives the labour times, the materials take-off, the margin and a worked example for the standard partition, then the uplifts for acoustic, metal-stud, wet-room and load-bearing-adjacent walls.

For the construction method see stud walls; for the sound-insulation detail see part e sound; for metal-stud alternatives see metal stud partition installation; for the carpenter's day rate behind these figures see carpenter day rate guide.

Key Facts

Quick Reference Table

Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.

Try squote free →
Item Regional (outside London/SE) South East London Notes
Standard stud wall, framed + boarded both sides, per m² labour £40–£70 £45–£80 £55–£95 47 × 75 or 47 × 100 mm CLS, 400 mm centres
Materials, standard, per m² £8–£15 £8–£15 £9–£16 Timber + board + fixings, before markup
Materials with 25 mm acoustic wool, per m² £12–£22 £12–£22 £13–£24
Plaster skim both sides, per m² labour £30–£50 £36–£56 £44–£66 Two sides at £15–£25 each
Door opening with lining and stop £80–£150 £100–£170 £120–£200 Excludes door and hanging
Door hung, hinges, latch, handle (door supplied) £60–£110 £70–£130 £90–£160
Architrave per door set, both sides £40–£80 £50–£90 £60–£110
Skirting per linear metre, both sides £6–£12 £8–£14 £10–£18
Acoustic partition uplift (Part E 40 dB) +20–40% +20–40% +20–40% Double board or 15 mm acoustic, wool, sealant
Metal-stud partition, per m² labour and materials £55–£95 £65–£110 £80–£130 Faster in long straight runs
Typical 3.6 m × 2.4 m partition with door opening (8.6 m²), all-in excluding door and decoration £700–£1,100 £850–£1,300 £1,050–£1,600 Framed, boarded, skimmed, skirting, architrave

Detailed Guidance

Measure and specify before you price

Walk the wall with the customer and settle:

  1. Length and height — measure the floor-to-ceiling height at both ends and in the middle; old ceilings vary 20–40 mm and the studs are cut individually
  2. What is on each side — a bedroom, a landing, a bathroom, a kitchen. This decides whether Part E applies, whether moisture-resistant board is needed and whether there is a fire requirement
  3. Door — position, swing, width (762 mm or 838 mm standard, 826 mm clear opening if Part M accessibility applies to a new ground-floor WC), and whether a door set or a separate lining
  4. Services — sockets, switches, lights on the wall, radiator pipes crossing it, a waste or soil pipe running inside it (which needs 100 mm studs and an access panel)
  5. Fixings in the finished wall — a basin, a TV bracket, a shower screen, wall units; each needs a noggin or an 18 mm plywood pattress at the right height, which costs minutes now and a return visit later
  6. Floor and ceiling structure — joist direction, floating floor, screed, lath-and-plaster ceiling (which needs the head plate into the joists, not the plaster)
  7. Finish — skim and paint, or dry-lined with taped and jointed board (cheaper, but visible in raking light; see scrim tape and jointing)

Write the specification into the quote: stud size, centres, board type and thickness, insulation, finish. A quote that says "stud wall" leaves the customer free to expect an acoustic wall at a single-board price.

Labour times

For a carpenter working alone, standard partition, domestic room:

Task Time
Set out, mark floor and ceiling, check for services 0.5 hr
Fix sole plate and head plate, cut and fix end studs 1 hr
Cut and fix studs at 400 mm centres, noggins, door head and cripples (per 3.6 m wall) 2 hrs
Fit door lining, plumb, pack and fix 1 hr
Board one side, cut around opening, fix at 150 mm centres 1 hr per 8.6 m²
Insulation and first-fix electrics window (electrician) by others
Board second side 1 hr
Skirting both sides, architrave both sides 1.5–2 hrs
Clear up, bag offcuts 0.5 hr
Total, carpenter, 8.6 m² partition with door opening 8.5–9.5 hrs (1.25–1.5 days)

Plus the plasterer: skim both sides of 8.6 m² (17.2 m²) is about a day with drying between coats, often split across two visits; plus the electrician's hour or two; plus the decorator. The carpenter's day rate at £261 (see carpenter day rate guide) makes the carpentry labour £330–£390, which at 8.6 m² is about £40–£45/m² for framing, boarding both sides and the door opening — consistent with the table, and the reason the table starts at £40 and not £25.

Materials take-off, 3.6 m × 2.4 m partition with one door opening

Item Quantity Trade cost
47 × 75 mm C16 CLS, 2.4 m lengths (plates 2 × 3.6 m, 9 studs, noggins, door head, cripples) 16 lengths £56
12.5 mm plasterboard 1200 × 2400 (8.6 m² × 2 sides ÷ 2.88 m² per board, +10%) 7 boards £63
Door lining set, 32 mm × 138 mm, with stop 1 £35
Plasterboard screws 38 mm, box 1 £8
Timber screws / nails, frame fixings for sole plate — £10
Scrim tape, angle bead for any external corner — £8
Skirting 119 mm MDF, 2 × 3.6 m less door, +10% 8 m £24
Architrave 69 mm MDF, 2 sets 11 m £25
Materials, trade £229
Markup 20% £46
Materials on quote £275

Add 25 mm acoustic mineral wool batts (8.6 m², about £35 trade) for an acoustic specification, and a second layer of board or 15 mm acoustic board (about £50–£70 more) for a Part E wall.

Worked example: standard partition, all-in

Carpentry labour: 1.4 days × £261                          = £365
Materials (above, with markup)                             = £275
Plasterer, skim both sides 17.2 m² × £18                   = £310
Plaster materials (2 bags Multi-Finish, PVA, beads) +20%   =  £35
Electrician, 1 double socket from existing ring, 1.5 hrs   = £110
Disposal of offcuts (own van, tip fee)                     =  £20
                                                            ------
Quote excluding door, hanging, decoration                  £1,115
Add: door hung £85, door supplied by customer
Add: decoration by others (mist coat + 2 coats both sides, £150–£250)

At the lower end of a regional market the same wall framed by a carpenter at £220 a day with a cheaper plasterer comes to about £900, and in London about £1,500. Quote the carpentry, plastering and electrics as separate lines so the customer sees what a "stud wall" actually contains, and so that if they drop the socket the price moves visibly.

Acoustic and Part E walls

A new internal wall between a bedroom or a room containing a WC and any other room must achieve 40 dB Rw under Approved Document E, section 5 (Table 0.1b, laboratory value). A basic single-board partition does not. The simplest build-up that does: 47 × 75 mm studs at 600 mm centres, 25 mm mineral wool quilt of at least 10 kg/m³ (not required by Table 5.1 but standard practice), one layer of 12.5 mm board each side with a minimum mass of 10 kg/m² per side — this is Approved Document E's wall type E-WS-1 and gives about 40 dB. Two layers of 12.5 mm board each side, or 15 mm acoustic board, pushes it to 45 dB and is what a loft-conversion Building Control inspector will usually want to see. Seal the perimeter with acoustic sealant, stagger board joints, and keep sockets back to back off each other by at least one stud bay. Price the uplift at 20–40% over the standard wall: the extra board, the wool, the sealant and the extra hour fitting it. See part e sound.

Metal stud as an alternative

For long, straight runs and commercial-type work, a 70 mm C-stud and track partition is faster to frame (no cutting studs to individual heights, no noggins except at board edges) and lighter, and it will not shrink or twist. It is harder to fix heavy items to without pattresses, it needs the right screws, and in a domestic job of one wall the time saved is small against the learning curve. Price it at £55–£95/m² supplied and fitted and boarded; see metal stud partition installation.

What to exclude, and say so

Frequently Asked Questions

How much does it cost to build a stud wall in the UK?

For a standard 3.6 m × 2.4 m partition with a door opening, framed, boarded both sides, plaster skimmed, with skirting and architrave, £700–£1,100 outside London in 2026, excluding the door, the electrics beyond one socket and decoration. London £1,050–£1,600. Per square metre, £60–£110 supplied, fitted and skimmed. An acoustic wall to Approved Document E adds 20–40%.

Does a stud wall need Building Regulations approval?

Not for a simple non-load-bearing partition dividing an existing room, in itself. It does if it creates a new habitable room or bathroom, affects a means of escape, changes ventilation requirements, or separates a bedroom or WC from other rooms (Part E sound). Loft-conversion partitions are always part of the notified project. When in doubt, a phone call to Building Control before quoting avoids a retrospective application.

What size timber should I use for a stud wall?

47 × 75 mm C16 CLS at 400 mm centres for walls up to about 2.4 m with no services in the cavity; 47 × 100 mm for taller walls, for acoustic walls (more cavity for insulation) and wherever a 50 mm waste or a soil pipe runs inside the wall. Noggins at mid-height and at every horizontal board joint. See stud walls.

Can I put a stud wall on a floating floor or a screed?

Yes, but the sole plate cannot be fixed through a floating floor into the subfloor without defeating the floating layer — fix to the walls and ceiling and rely on the perimeter fixings, or lift the floating floor along the line of the wall and fix to the structure below. On a screed, use frame fixings or concrete screws into the slab, and check for underfloor heating pipes or electric mats with a thermal camera or the installation drawings before drilling.

Why is the plastering nearly as much as the carpentry?

Because a stud wall has two faces and the skim is priced per face: 8.6 m² of wall is 17.2 m² of plastering, with beads at the door and both ends, in two coats with drying time. The carpentry is one wall; the plastering is two walls. Dry-lining with taped and jointed boards is cheaper but shows in raking light and most customers want a skim.

Regulations & Standards