Summary
Pricing per point is the electrical trade's equivalent of the bricklayer's price per thousand: a unit rate that lets you quote a rewire or a new build from a drawing in twenty minutes and reconcile it against your day rate afterwards. Builders and developers expect it. Domestic customers increasingly ask for it, because every price-comparison site publishes a "cost per socket". Used well, it gives consistent, defensible pricing across jobs. Used badly, it hides the circuits, the consumer unit, the bonding and the testing that make up a third of a rewire's real cost, and leaves the electrician absorbing them.
The key is to be precise about what a point is, what the rate includes, and what sits outside it. A point rate should cover the labour and the cable to one accessory position across both fixes, and nothing else. The consumer unit, the meter tails, main and supplementary bonding, the earth electrode on a TT system, chasing and making good, testing, certification and notification are all separate lines, because they do not scale with the number of points. A 20-point flat and a 60-point house both need one consumer unit and one set of certificates.
This guide gives 2026 point rates by region and job type, the definition of a point that avoids arguments, the first fix / second fix split, what to charge for the fixed items, and a worked example for a three-bed rewire. It assumes the electrician is pricing labour and cable with accessories either supplied at cost plus a mark-up or by the builder. For hourly and day rates see electrician hourly rate guide; for whole-job rewire figures see full rewire pricing guide.
Key Facts
- Definition of a point — one accessory position fed from a circuit: a single or double socket (counts as one), a light fitting and its switch (one point; a two-way switched light is usually 1.5 points or a stated extra), a cooker control unit and outlet (one point, often rated as two because of the 6 mm² or 10 mm² cable), a fused connection unit, a shaver socket, an extractor fan connection, a smoke or heat alarm head
- 2026 point rates (labour and cable, both fixes) — regional £55–£90; South East £65–£100; London £75–£120. New-build and multi-unit work sits at the bottom of each band; occupied-house rewires at the top because of protection, making good and working around furniture
- First fix share — roughly 55–60% of the point rate: cable runs, back boxes, chasing or clipping, drilling joists and studs, labelling at the board position
- Second fix share — roughly 40–45%: fitting accessories, connecting at the consumer unit, dressing and sleeving, initial energisation
- Typical point counts — one-bed flat 20–30; two-bed house 35–45; three-bed semi 50–65; four-bed detached 70–95
- Fixed items outside the point rate — consumer unit supply and fit £450–£800 (10–16 way, RCBO board to BS EN 61439-3 with Type A RCDs and SPD); meter tails and isolator £80–£150; main protective bonding to water and gas £80–£160; supplementary bonding where required £60–£120 per location; TT earth electrode £150–£300; testing and EIC £150–£300; Part P notification fee via scheme £5–£15 per job; Building Control notification where not scheme-registered £200–£400
- Circuits are priced separately from points — each new circuit (ring final, lighting, cooker, shower, immersion, EV charger, smoke alarm) carries a circuit charge of £60–£120 for the home run to the board and the protective device, or is rolled into the consumer unit price
- Cable allowances inside the rate — 2.5 mm² for socket points (ring final or 20 A radial), 1.5 mm² for lighting (6 A or 10 A), 6 mm² or 10 mm² for cookers and showers (cooker and shower points are usually charged at 1.5–2× the standard point to cover cable cost)
- Chasing and making good — chase in masonry and make good with bonding or plaster: included in the occupied-house rate or charged at £8–£15 per metre; plasterers' re-skim is the builder's cost unless stated
- Testing and certification — every new installation or rewire requires an Electrical Installation Certificate with schedule of inspections and test results under BS 7671 Part 6; alterations to existing circuits that do not add a circuit take a Minor Electrical Installation Works Certificate
- Notification — a rewire, a new circuit or a consumer unit replacement is notifiable under Approved Document P (England) and Part P of Schedule 1 to the Building Regulations 2010; self-certify through NICEIC, NAPIT, ELECSA or similar, or notify Building Control before starting
- Day rate reconciliation — an electrician fitting 10–14 first-fix points a day in a stripped house, or 15–20 second-fix points a day, earns £280–£380 a day at the rates above; if your point rate does not reconcile with your day rate, one of them is wrong
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Item | Regional (ex VAT) | South East | London | Notes |
|---|---|---|---|---|
| Socket point (single or double), labour and cable | £55–£85 | £65–£95 | £75–£115 | Ring final or radial; accessory extra |
| Lighting point (fitting and one switch) | £55–£85 | £65–£95 | £75–£115 | Pendant or batten; downlights priced per fitting |
| Two-way or intermediate switching | +£20–£35 per extra switch | +£25–£40 | +£30–£50 | Extra strapper cable and switch |
| Cooker point (control unit and outlet, 6 mm²) | £110–£160 | £130–£180 | £150–£220 | Counts as circuit plus point |
| Electric shower point (10 mm², pull cord, isolator) | £140–£220 | £160–£250 | £190–£300 | Plus 45–50 A RCBO; see shower guides |
| Fused connection unit / spur for appliance | £55–£85 | £65–£95 | £75–£115 | Boiler, fan, hob ignition |
| Smoke/heat alarm head (interlinked, mains) | £60–£90 | £70–£100 | £80–£120 | Alarm head supply £20–£45 extra |
| Outside light or socket point | £80–£130 | £90–£150 | £110–£180 | IP-rated accessory, external route |
| Consumer unit, 12–16 way RCBO with SPD, fitted | £450–£800 | £550–£900 | £650–£1,100 | Includes tails and isolator check |
| Main bonding (water and gas) | £80–£160 | £100–£180 | £120–£220 | 10 mm² to BS 7671 544.1 |
| Testing, EIC and scheme notification | £150–£300 | £180–£350 | £220–£400 | Per installation |
| Full rewire, 3-bed semi, 55 points, all-in | £5,500–£8,500 | £6,500–£10,000 | £8,000–£12,500 | Ex accessories above standard white |
Detailed Guidance
Define the point before you count it
Most per-point disputes are about counting, not pricing. Put the definition in the quotation:
- Socket point — one single or double 13 A socket outlet to BS 1363, on a ring final or radial circuit, including back box and cable. A double socket is one point, not two. A quad (two doubles side by side) is two points.
- Lighting point — one luminaire position and its switch, including the cable between them and to the circuit. Each additional switch controlling the same light (two-way landing switches) is an extra at a stated rate. A room with five downlights on one switch is five lighting points, not one, because each fitting is a cable position, a hole and a connection.
- Switched fused spur / FCU — one point.
- Cooker point — control unit, outlet plate and the 6 mm² (or 10 mm²) cable to the board: one point charged at the cooker rate.
- Heavy points — shower, immersion, EV charger, hob isolator: each priced individually because the cable, protective device and testing time dominate.
- Data, TV, alarm and doorbell — not electrical points; price per outlet separately or exclude.
Also state what the point rate excludes: accessories above a standard white moulded range, decorative pendants and fittings, chasing in solid walls (if excluded), making good, lifting and relaying floorboards and carpets, builder's work (notching joists, forming holes through external walls), and anything downstream of a client-supplied item.
First fix: what you are pricing
First fix is the cable installation before plaster: running cables, fixing back boxes, chasing, drilling, clipping in voids, pulling to the board position and labelling. In a stripped house with floorboards up and ceilings down, a competent electrician installs 10–14 points a day. In an occupied house with furniture, carpets and finished ceilings, that drops to 6–9 points a day, which is why occupied rewires sit at the top of the price bands. First fix is where the real variable cost lies, so if you price only one of the two fixes by the point, price this one carefully.
Cable costs feed the first-fix rate. At 2026 prices a 100 m drum of 2.5 mm² twin and earth is around £70–£95 and 1.5 mm² around £45–£65; a typical point uses 8–15 m, so £7–£12 of cable per point. Cooker and shower cable at 6 mm² and 10 mm² costs £2.50–£5 per metre, which is why those points carry a premium.
Second fix: what you are pricing
Second fix is fitting the accessories after plastering and decoration, terminating at the consumer unit, and energising. Rates of 15–20 points a day are realistic for standard white accessories; metal-clad or screwless ranges with awkward terminals slow it to 12–15. Second fix also includes the time to find the cables the plasterer buried, so always photograph and measure the first fix.
Circuits and the consumer unit are not points
A rewire with 55 points typically has 8–12 circuits: two or three ring finals (or 20 A radials), two or three lighting circuits, cooker, shower, immersion or boiler, smoke alarms, and perhaps an outside or garage circuit. Each circuit is a home run to the board, a protective device, and a set of tests (continuity, insulation resistance, polarity, earth fault loop impedance, RCD operation). Price them either as a per-circuit charge of £60–£120 or as part of a consumer unit price that states the number of ways. Current practice is an RCBO per circuit with Type A devices, a surge protective device (BS 7671 Section 443), and an all-metal enclosure to BS EN 61439-3 as required by Regulation 421.1.201 for domestic consumer units.
Main protective bonding to the incoming water and gas services in 10 mm² (Regulation 544.1.1) is required on every rewire and is frequently found missing; price it as a fixed item. Supplementary bonding in bathrooms is not required where the conditions of Regulation 701.415.2 are met (all circuits RCD-protected and the main bonding in place), but check and price it where it is.
Testing, certification and notification
Testing a 55-point, 10-circuit rewire takes a competent electrician most of a day, and the Electrical Installation Certificate with its schedules another hour or two. Price it as a line: £150–£300. Notification through a competent person scheme (NICEIC, NAPIT, ELECSA, Stroma and others) costs a few pounds per job and generates the Building Regulations compliance certificate the customer needs when they sell. An electrician who is not scheme-registered must notify Building Control before starting, and the authority's fee (£200–£400) and inspection add to the price. See part p notifiable work and part p notifications.
Reconcile the point rate with the day rate
The sanity check that stops a point rate drifting: multiply your realistic points per day by the point rate and compare it with your day rate including overheads. At 12 first-fix points a day and a £35 first-fix share, you earn £420 before cable (£100–£140), so about £300 net labour. At 17 second-fix points a day and a £25 second-fix share, £425 before accessories. Both sit around the £280–£380 day rate a self-employed electrician needs outside London (see day rate to hourly rate calculator). If your point rate gives £220 a day, raise it; if it gives £600, you will not win the work.
Worked example: three-bed semi rewire, regional rates
| Element | Count | Rate | Total (ex VAT) |
|---|---|---|---|
| Socket points | 26 | £70 | £1,820 |
| Lighting points | 17 | £70 | £1,190 |
| Two-way switching (hall/landing, kitchen) | 3 | £28 | £84 |
| Cooker point | 1 | £135 | £135 |
| Electric shower point (10 mm², pull cord) | 1 | £180 | £180 |
| FCUs (boiler, extractor fans × 2, hob) | 4 | £70 | £280 |
| Smoke/heat alarm heads, interlinked (hall, landing, kitchen) | 3 | £75 | £225 |
| Outside light and outside socket | 2 | £105 | £210 |
| Points subtotal | 57 | £4,124 | |
| Consumer unit, 14-way RCBO, SPD, tails check | 1 | £620 | £620 |
| Main bonding to water and gas | 1 | £120 | £120 |
| Testing, EIC, scheme notification | 1 | £220 | £220 |
| Accessories: standard white range, 57 positions, at cost + 20% | £410 | ||
| Smoke/heat alarm heads supply | 3 | £32 | £96 |
| Making good chases (bonding only, decorator to finish) | 1 | £350 | £350 |
| Total | £5,940 |
Programme: 5 days first fix (two electricians 2.5 days), 3 days second fix and testing. Labour content about 8 electrician-days at £5,940 less £1,600 materials gives roughly £540 per electrician-day gross, or £330–£380 net after van, consumables, insurance and the unpaid quoting and admin time, which is where it should be.
Pricing for builders versus homeowners
Builders want a point rate and a schedule; they usually supply nothing, chase nothing and make good nothing, and they expect you to turn up when the plasterer has gone. Price at the lower end of the bands, state the point definition and count, and add a clause for return visits caused by other trades. Homeowners want a total; give it, but build it from the points so that the inevitable "can we add three more sockets" has a ready answer. Either way, put the rates for additional points in the quotation: it converts scope creep into paid work.
Frequently Asked Questions
Is a double socket one point or two?
One. The industry convention, and the one most price lists follow, is that a point is an accessory position regardless of the number of gangs. A double socket takes marginally longer to connect than a single and the accessory costs a few pounds more, but the cable run, the back box and the chase are the same. Two separate double sockets side by side are two points.
Should downlights be priced per point?
Yes, each downlight is a point, because each one is a hole, a cable position and a connection, and a room with eight downlights takes far longer than a room with one pendant. Many electricians use a reduced "additional fitting on the same switch" rate of £35–£55 for the second and subsequent downlights in a room, and charge the fitting supply separately. See downlight installation pricing guide.
Does the point rate include the consumer unit and testing?
It should not, and your quotation should say so. The consumer unit, bonding, tails, testing and certification are fixed costs that do not scale with points, so including them in the point rate overcharges small jobs and undercharges large ones. Price them as separate lines on every job.
What is notifiable under Part P, and who pays the fee?
In England a rewire, any new circuit, a consumer unit replacement, and work in a special location (bathroom zones) are notifiable. Adding a socket or light to an existing circuit outside a special location is not. If you are registered with a competent person scheme, you self-certify for a few pounds per job and the customer receives a Building Regulations compliance certificate. If not, a Building Control application must be made before the work starts and the fee is a job cost; price it in. Wales has its own version of Part P; Scotland uses the Building (Scotland) Regulations and the certification of construction scheme.
How do I price adding points to an existing circuit rather than a rewire?
Use a higher rate, typically £90–£160 per additional point, because the job carries a callout, access to an existing circuit, testing of that circuit, a Minor Works Certificate and usually some making good, with none of the economies of a stripped house. See extra sockets and lights pricing guide.
Regulations & Standards
BS 7671:2018+A2:2022 — Requirements for Electrical Installations (IET Wiring Regulations): circuit design (Chapter 43 and Appendix 15 for ring finals), cable selection (Chapter 52), protective bonding (Chapter 54, Regulation 544.1), consumer unit enclosures (421.1.201), surge protection (Section 443), locations containing a bath or shower (Section 701), inspection and testing (Part 6)
Building Regulations 2010, Schedule 1 Part P and Approved Document P (2013 edition) — electrical safety in dwellings; notifiable work and competent person self-certification
Building Regulations 2010, Approved Document M — socket and switch heights (450–1,200 mm above floor) in new dwellings
BS 1363 — 13 A plugs, socket outlets, adaptors and connection units
BS EN 61439-3 — low-voltage switchgear and controlgear assemblies: distribution boards for operation by ordinary persons (consumer units)
BS EN 61008 / BS EN 61009 — RCCBs and RCBOs for household use
BS 5839-6:2019+A1:2020 — fire detection and alarm systems for domestic premises (smoke and heat alarm points)
Electricity at Work Regulations 1989 — safe working on and testing of electrical systems
IET Guidance Note 3: Inspection and Testing — the test procedures behind the EIC
Approved Document P: Electrical safety — GOV.UK — notifiable work and certification in England
BS 7671 IET Wiring Regulations — IET — current edition and amendments
Electrical Safety First: Part P and competent person schemes — plain-language guidance on notification
NICEIC: Domestic installer registration — competent person scheme requirements
Competent person schemes — GOV.UK — list of authorised schemes
electrician hourly rate guide — the hourly and day rate the point rate must reconcile with
full rewire pricing guide — whole-job rewire pricing by property size
extra sockets and lights pricing guide — pricing additions to existing circuits
consumer unit replacement pricing guide — the fixed item that sits outside the point rate
part p notifiable work — what must be notified and how
ring final circuit explained — the circuit most socket points sit on
first fix second fix — how the fixes sequence with the other trades