Summary
Bath resurfacing is a niche with high margins and a bad reputation, and the two are connected. Done properly, a sprayed two-pack polyurethane or acrylic-urethane coating over a correctly keyed and etched surface lasts 10–15 years and costs the customer a third of a bath replacement with no tiling, plumbing or making good. Done badly (brush-on DIY kits, no acid etch, cartridge mask, no extraction, cured for six hours instead of 24), it peels within a year and the trade gets blamed. Pricing has to reflect the professional version: the correct coatings system, the preparation time, the breathing protection and extraction that HSE requires, and the return visit when the customer rings about a drip mark.
The health and safety point is not optional. Virtually all professional bath coatings are two-pack systems whose hardener contains isocyanates, the leading cause of occupational asthma in the UK. HSE's guidance on isocyanate-containing paints is explicit that spraying should be done with air-fed breathing apparatus, with the area ventilated or extracted, and that the operator should have health surveillance including lung-function testing. A bathroom is a small, poorly ventilated room; a resurfacer who sprays with a half-mask is risking a life-changing illness and a prosecution. Build the equipment into the price.
This guide prices the standard job, the cast-iron roll-top, colour changes, chip and crack repairs, shower trays and basins done at the same visit, and the alternatives (replacement under bath replacement pricing guide, or hot re-enamelling for period cast-iron baths). It gives the materials list, the time breakdown, the drying and curing allowances that determine when the customer can bathe, and how to structure the guarantee.
Key Facts
- Coating systems — professional kits are two-pack aliphatic polyurethane or acrylic-urethane, sprayed; single-pack brush-on epoxy kits are DIY grade and are the source of most "resurfacing peeled" complaints.
- Material cost per bath — coating kit (primer, topcoat, hardener) £35–£80; etch or adhesion promoter £8–£15; polyester or epoxy filler for chips £6–£12; abrasives, tack cloths, masking film and tape, solvent and wipes £15–£30. Total £60–£140.
- Substrates — cast iron (vitreous enamel), pressed steel (vitreous enamel), acrylic, GRP and resin-stone composites all take a resurfacing system, but each needs its own preparation and primer; many systems are not rated for acrylic baths, so check the data sheet.
- Preparation time — 1.5–2.5 hours: remove silicone, clean with degreaser, abrade with 240–400 grit, acid-etch enamel or use an adhesion promoter, rinse, dry fully, fill chips, mask everything within 2 m.
- Spray time — 30–60 minutes for two or three coats with flash-off between coats.
- Touch-dry — 1–4 hours depending on system; return to service 24–48 hours (some systems 72 hours); full cure 5–7 days, during which no bath mats, abrasive cleaners or standing water.
- Film thickness — most systems specify 100–200 microns total dry film; too thin wears through at the drain, too thick runs.
- Service life — 10–15 years for a professionally applied two-pack system with sensible use; 3–5 years is typical for brush-on kits.
- Guarantee — resurfacing firms commonly offer 3–5 years against peeling and adhesion failure, excluding impact damage and chemical attack.
- Isocyanate exposure — HSE's workplace exposure limit for isocyanates is 0.02 mg/m³ (8-hour TWA) and 0.07 mg/m³ (15-minute STEL), expressed as NCO; spraying in a bathroom will exceed these without extraction and air-fed RPE.
- Breathing protection — HSE guidance: air-fed visor or mask (compressed air breathing apparatus to BS EN 14594 or similar) for spraying isocyanates; disposable cartridge masks are not acceptable for spraying.
- Equipment outlay — HVLP turbine spray gun £250–£700; air-fed breathing system with filtered compressor supply £600–£1,500; portable extraction fan and ducting £150–£400; infrared or hot-air curing lamps optional £100–£300.
- Health surveillance — COSHH Regulation 11 requires health surveillance for employees exposed to isocyanates; self-employed operators are strongly advised to have annual lung-function testing.
- Hot re-enamelling — a factory process where the bath is stripped and re-fired with vitreous enamel at around 800 °C; £600–£1,500 plus £300–£700 removal and refit, only viable for cast iron.
- Comparison — a mid-range acrylic bath replaced including plumbing, panel and making good costs the customer £800–£1,800; see bath replacement pricing guide.
- Labour rate — specialist resurfacers charge the equivalent of £50–£90 per hour; a half-day minimum is standard. See bathroom fitter day rate guide for comparable trade rates.
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Materials (your cost) | Time on site | Your cost (incl. labour at £55/h) | Customer price (30–45% margin) |
|---|---|---|---|---|
| Standard 1,700 mm bath, white, enamel steel | £60–£100 | 3–4 h | £225–£320 | £280–£480 |
| Standard bath, acrylic (where system permits) | £70–£110 | 3.5–4.5 h | £260–£360 | £330–£520 |
| Cast-iron roll-top, inside only | £80–£130 | 4–5 h | £300–£405 | £400–£620 |
| Cast-iron roll-top, inside and painted exterior | £120–£180 | 6–8 h | £450–£620 | £600–£950 |
| Colour change (e.g. avocado to white) | £80–£140 | 4–5.5 h | £300–£445 | £400–£680 |
| Chip or crack repair, localised blend | £15–£35 | 1.5–2.5 h | £100–£170 | £120–£250 |
| Add shower tray at same visit | £40–£70 | +1.5–2.5 h | +£120–£210 | +£160–£300 |
| Add basin at same visit | £25–£45 | +1–1.5 h | +£80–£130 | +£100–£180 |
| Anti-slip texture to bath floor | £15–£30 | +0.5 h | +£40–£60 | +£60–£90 |
| Hot re-enamelling, cast iron (sub-contract) | £600–£1,500 | removal/refit 4–6 h | £900–£1,900 | £1,200–£2,600 |
Prices are 2024 regional England excluding VAT. London adds 20–35%. The margin on resurfacing is higher than general trades because the equipment outlay, health-surveillance cost and callback risk are carried by a small number of jobs per week.
Detailed Guidance
Survey: is the bath a resurfacing candidate?
Not every bath should be resurfaced, and pricing one that is not is how a £400 job becomes a free replacement under your guarantee.
RESURFACE OR REPLACE?
│
├─ Cast iron or pressed steel enamel, sound, chips and dullness only?
│ └─ YES ──> Resurface. Best substrate.
│
├─ Pressed steel with rust through at the waste or overflow?
│ └─ YES ──> Replace. Rust under a coating lifts it within a year.
│
├─ Acrylic, flexing noticeably when stood in?
│ └─ YES ──> Replace or re-support. Movement cracks any rigid coating.
│
├─ Acrylic, rigid, surface scratched or discoloured?
│ └─ Check system data sheet for acrylic approval ──> Resurface with correct primer.
│
├─ Previously resurfaced, now peeling?
│ └─ Must strip ALL old coating (chemical stripper, 2–4 h extra) ──> Price as premium or decline.
│
└─ Period roll-top with sentimental or architectural value?
└─ Resurface in situ (good) or hot re-enamel (best, dearest).
At survey, also confirm: ventilation (an openable window or extract fan you can duct to), electrical supply for the turbine, extraction and compressor, water isolation (the bath must be bone dry; a dripping tap ruins the primer), and whether the silicone and bath panel must be removed and replaced (add 30–45 minutes and £8–£15 of sanitary silicone).
Preparation is the price
The sprayed coat takes less than an hour. Everything that determines whether it lasts happens first:
- Strip silicone from the bath-to-tile joint and around the waste and overflow. Residual silicone is the number one cause of edge peeling.
- Degrease with a dedicated cleaner; soap residues and bath-oil films repel primers.
- Abrade the whole surface with 240–400 grit wet-and-dry to a uniform matt finish.
- Etch enamel with the system's acid etch (or use an adhesion promoter where the manufacturer specifies), rinse thoroughly, and dry completely with a hot-air gun; trapped water under primer blisters.
- Fill chips with the system's polyester or epoxy filler, sand flush, re-etch locally.
- Mask the taps, waste, overflow, tiles and the entire bathroom within spray range with film and tape; overspray on tiles and chrome is a callback.
- Tack-cloth immediately before spraying.
Allow 1.5–2.5 hours. Quoting less means skipping a step.
Spraying, drying and curing
Mix the two-pack system to the stated ratio by weight or volume; pot life is typically 1–4 hours. Apply the primer where the system uses one, then two or three topcoats with the stated flash-off (often 10–20 minutes) between, to the specified film build. HVLP turbine guns at 1.3–1.8 mm tips are the trade norm; they reduce overspray and bounce-back in a small room.
Drying is where customer expectations and physics collide. State in writing: touch-dry in 2–4 hours, no water for 24 hours (48 or 72 for some systems and for cold bathrooms), full cure 5–7 days. Infrared lamps shorten the return-to-service time and can be worth the £100–£300 investment if you do several baths a week. Tell the customer in writing not to use bath mats with suction cups, abrasive or bleach-based cleaners, or to leave standing water in a blocked bath, and that the waste should be checked for drips, because a constant drip wears a track through any coating.
Isocyanates: the equipment and the law
HSE's guidance for the motor vehicle repair sector and for isocyanate paints generally applies equally in a bathroom: two-pack polyurethane spraying is the leading cause of occupational asthma in Britain, once sensitised you can never work with the material again, and the controls are extraction, air-fed RPE and health surveillance. Practically:
- Extraction: a portable fan ducted to an open window or the extract vent, running during spraying and for the clearance time afterwards. The bathroom door closed, the rest of the house protected.
- RPE: an air-fed visor or full-face mask fed from a compressor with a breathing-air filter, or a self-contained compressed-air system. Not a cartridge half-mask. Fit-tested where it is a tight-fitting type.
- Clearance time: do not remove the RPE until the mist has cleared, which in a bathroom with extraction is typically 15–30 minutes after the last coat.
- Health surveillance: a pre-employment questionnaire and annual lung-function test (spirometry) for anyone exposed. Occupational health providers charge £60–£150 per person per year.
- Skin: nitrile gloves and coveralls; isocyanates also sensitise through the skin.
- Customers and occupants: out of the house or at least out of the room and the room sealed until clearance; no pets.
Amortise the equipment and surveillance into the price. An operator doing four baths a week needs roughly £15–£30 per job to cover RPE consumables, filter changes and health checks alone.
Colour changes, roll-tops and exteriors
A colour change (coloured 1970s suites to white) needs an extra coat or a tinted primer for coverage and takes longer to mask and inspect. Price at the top of the range. Cast-iron roll-tops are larger, deeper and have a rolled rim that takes longer to prepare; the exterior is normally repainted rather than resurfaced, with a rust-inhibiting primer and a satin or gloss enamel, and takes 2–3 hours more. Feet are often removed, stripped and repainted separately. A full roll-top restoration in situ at £600–£950 is good value against hot re-enamelling at £1,200–£2,600 plus the plumbing disruption.
Guarantee and callbacks
Offer a written guarantee of 3–5 years against peeling, flaking and loss of adhesion, excluding impact chips, chemical damage, bath mats, dripping taps left unrepaired and failure to follow the care instructions. Keep photographs of the bath before, after preparation and after coating. A realistic callback rate for a well-run operation is 2–5% of jobs, mostly small edge lifts at the waste or silicone line, taking an hour to repair. Build that into the margin; it is why resurfacing prices carry 30–45% rather than the 20–25% typical of general bathroom fitting.
Frequently Asked Questions
How long does a resurfaced bath last?
A professionally sprayed two-pack polyurethane or acrylic-urethane system on a properly prepared enamel bath lasts 10–15 years in a family bathroom, longer in a lightly used one. The failure points are the waste (dripping taps and standing water), the silicone line (movement and residual silicone) and impact chips from dropped shower heads. Brush-on epoxy kits typically fail in 3–5 years because the coating is thinner and the preparation is usually skipped. Tell the customer honestly that it is a refurbishment, not a new bath.
Can acrylic baths be resurfaced?
Some systems are approved for acrylic and GRP with a specific adhesion primer; others are enamel-only. The practical test is rigidity: an acrylic bath that flexes when stood in will crack any coating, and no primer fixes that. Check the manufacturer's data sheet, and if the bath flexes, quote a replacement instead.
Is resurfacing cheaper than a new bath?
Usually by half or more once tiling, plumbing, the panel and making good are counted. A new mid-range acrylic bath supplied and fitted, with the old one removed, new waste and trap, panel and re-siliconing, is £800–£1,800 installed; if a tiled-in steel bath is removed, add retiling. Resurfacing at £280–£550 with no disruption beyond 24–48 hours out of use is the customer's cheaper option where the bath is structurally sound. Where it is rusting or flexing, replacement is cheaper in the long run.
Why can't I just use a cartridge mask?
Because isocyanate spray mist is a respiratory sensitiser with an exposure limit so low (0.02 mg/m³) that cartridge masks cannot be relied upon to keep you below it in an enclosed room, and because once you are sensitised the condition is permanent. HSE guidance specifies air-fed breathing apparatus for spraying isocyanate paints. The equipment costs £600–£1,500, which is three or four baths' profit; occupational asthma costs a career.
What should the customer do after the job?
Nothing for 24–48 hours (or the period your system specifies), then normal use with non-abrasive cleaners, no bleach soaks, no suction-cup mats, no standing water, and any dripping tap fixed promptly. Give them a printed care sheet; it is also the document your guarantee refers to.
Regulations & Standards
Control of Substances Hazardous to Health Regulations 2002 (COSHH) — assessment, control of exposure (Regulation 7), maintenance of controls (Regulation 9) and health surveillance (Regulation 11) for isocyanate exposure.
HSE EH40/2005 Workplace Exposure Limits (as amended) — isocyanates, all (as NCO): 0.02 mg/m³ 8-hour TWA, 0.07 mg/m³ 15-minute STEL.
HSE guidance on isocyanate paints (including HSG276 Current Control Measures for Isocyanate Paints and the MVR isocyanate guidance) — air-fed RPE, extraction, clearance times and health surveillance.
Personal Protective Equipment at Work Regulations 1992 (as amended 2022) — provision and maintenance of RPE and skin protection.
BS EN 14594 — Respiratory protective devices: continuous-flow compressed-air line breathing apparatus.
BS EN 14516 — Baths for domestic purposes (product standard for the bath itself, relevant to replacement comparisons).
Water Supply (Water Fittings) Regulations 1999 — where waste, overflow or taps are disturbed and refitted.
Environmental Protection Act 1990 (Duty of Care) and Hazardous Waste Regulations 2005 — disposal of solvent, hardener and contaminated masking.
HSE – Isocyanates: Safety in motor vehicle repair and other paint spraying — the controls HSE expects for spraying two-pack paints
HSE – EH40/2005 Workplace exposure limits — current exposure limits for isocyanates
HSE – COSHH essentials: Control of Substances Hazardous to Health — regulation guidance and health surveillance duties
HSE – Respiratory protective equipment at work (HSG53) — selecting and using RPE
British Coatings Federation – Two-pack isocyanate paints guidance — industry guidance on handling two-pack coatings
BSI – BS EN 14516 Baths for domestic purposes — bath product standard
bath replacement pricing guide — the alternative the customer is weighing resurfacing against
bathroom fitter day rate guide — comparable labour rates
coshh assessment — writing the COSHH assessment this work requires
ppe selection guide — selecting and fit-testing RPE
bath installation — what replacement involves if resurfacing is not suitable
markup to margin explained — setting the margin on a high-callback trade