Kitchens

26 articles

• How Are Quartz and Stone Worktops Templated and Fitted?
  Stone worktop install: laser/MDF templating ±0.5-1mm; CNC fabrication; bedded on silicone; 1-2mm epoxy joints; HSE silica wet cut only; FFP3 RPE mandatory
• How Do You Fit Kitchen Plinths, Cornice and Pelmet Cleanly?
  Plinth (150mm × 18mm) clipped to legs, scribed to floor, mitre external corners, floor seal strip; cornice screw-fixed from cabinet top; pelmet hides under-cab LED
• How Do You Install an Induction Hob to UK Wiring Regs?
  Induction 7.2kW typical: 32A MCB + 30mA RCD, 6.0mm² T&E, 45A cooker switch + CCU; 50mm air gap below; 650mm to hood; aperture 560×490mm + 50mm radii
• How Do You Install Integrated Kitchen Appliances?
  Integrated fridge/dishwasher/oven: carcass tolerance ±2mm; 200mm² fridge vent; decor door bracket kits ±3mm adjust; dedicated 13A spurs; Part P notifiable
• How to Install a Kitchen Island: Building Regs & Services
  Floor fixing requirements, Part P for island sockets, Gas Safe for island hobs, worktop cantilever limits (300mm unsupported), extractor requirements when hob present
• Kitchen Appliance Circuits: Dedicated Wiring & Isolation UK
  Kitchen appliance circuits: dedicated circuits for cooker/hob, FCU for dishwasher/washing machine (13A fuse, accessible location), under-unit lighting (SELV 12V or 230V IP44), RCBO consumer unit preference
• Kitchen Cabinet Installation Order
  Kitchen install order: tall units → wall units → base units → worktop → plinths → appliances → cornice/pelmet; BS 6222-2:2009; level from highest floor point
• Kitchen Door Hinges & Drawer Runners: Blum vs Grass UK
  Blum Clip Top vs Grass Tiomos hinge adjustment (3-way), soft-close damper replacement, push-to-open Blumotion, Legrabox vs Tandem Box drawer runner load ratings
• Kitchen Drainage Installation: Sink Waste & Dishwasher Guide
  40mm minimum waste, 1:40–1:80 gradient, P-trap vs bottle trap, dishwasher standpipe minimum 600mm (Water Regs anti-siphon), AAV installation, waste disposal units
• Kitchen Electrical Regulations: Socket Heights & Part P UK
  Kitchen electrical layout: socket zones, dedicated circuits, Part P notifiable work, isolation requirements near sinks
• Kitchen Extract Ducting: 150mm vs 125mm Rigid & Flexible
  150mm rigid preferred over 125mm, flexible duct run max 3m with 2 bends, Approved Document F 30 l/s minimum extract rate, anti-condensation insulation on cold runs
• Kitchen Extraction and Ventilation: Part F Rates and Ducting
• Kitchen Extraction Requirements: Part F Cooker Hood Guide
  Kitchen extraction requirements: minimum 30 l/s ducted rate, recirculation filters, Approved Document F (2021) compliance
• Kitchen Layout Dimensions: Work Triangle & Walkway Guide
  Kitchen layout dimensions: galley, L-shape, U-shape, island; minimum aisle widths, triangle principle, standard unit heights
• Kitchen Lighting Design: Task Lighting & Zone Rules UK
  Task lighting 300 lux minimum at worktop, under-cabinet LED 24V DC, downlight placement 400mm from wall, BS 7671 Zone 1/2 rules above sink, DALI dimming compatibility
• Kitchen Plumbing Guide: Waste Pipes, Supply & Appliances UK
  Kitchen plumbing: waste pipe sizing, trap types, supply connections, dishwasher standpipe, washing machine requirements
• Kitchen Sink Installation: Undermount, Inset & Belfast Guide
  Undermount silicone bead and under-clamping, Belfast support frame, 35mm waste kit, Part G flow rate 8 l/min, braided hose ≤500mm and WRAS fittings
• Kitchen Splashback Options: Glass, Tile & Steel Fitting Guide
  Glass splashback standoffs and heat-resistant silicone 300mm+ from hob, ceramic tile adhesive selection, solid surface seamless joins, stainless steel fixing and bead finish
• Kitchen Unit Installation: Levelling, Wall Fixing & Fitting
  Levelling legs 100–150mm adjustment range, wall cabinet fixings (70mm+ into masonry, 2× 10mm bolts into stud), cornice/pelmet scribing, kick board clips and infill
• Kitchen Worktop Fitting: Scribing, Joiners & Sink Cuts
  Worktop fitting: scribing technique (compass along wall), mitre joiners (4 minimum), undermount sink router method (MDF template, guide bush, two passes), upstand sealed with sanitary silicone
• Kitchen Worktop Jointing: Butt, Mitre and Mason's
  Worktop joint methods: butt, 45° mitre, mason's mitre (Trend WJ jig + connector bolts), hot-rod for solid surface, dry/epoxy for stone; BS EN 14322, BS EN 312, BS EN 438; PVA core sealing, colour-fill
• Kitchen Worktop Materials: Laminate vs Quartz vs Granite
  Laminate £40-100, wood £80-200, quartz £250-500, granite £200-600, solid surface £400-800, sintered £350-700 per lin m supplied; heat tolerance, scratch, stain, joint and repair comparison; HSE silicosis warning on quartz fabrication; BS EN 16384 worktop standard
• Kitchen Worktop Materials: Laminate, Granite, Quartz Guide
  Kitchen worktop comparison: laminate, granite, quartz, solid surface, hardwood — durability, maintenance, heat/scratch resistance
• UK Kitchen Extraction Rules: Part F Ventilation Guide
  ADF 2021: 30 L/s above hob / 60 L/s elsewhere; 150mm duct, <3m run, 2 bends max; recirculating non-compliant; external grille required; trickle vents for make-up air
• Which Kitchen Worktop Material Is Right for the Job?
  Worktops: laminate £25-90/m to sintered £400-900/m; quartz silica WEL 0.1mg/m³; heat tolerance laminate 80°C, quartz 150°C, sintered 300°C+; BS 8000-15 install
• Worktop Templating and Fitting: Stone, Laminate and Wood
  Stone, laminate, solid wood worktop templating (MDF/laser) and fitting; cabinet ±1mm level tolerance for stone, lead times, cutouts, sink support, mason's mitres; BS EN 14617/438/13629