Summary
Combustion needs air, and an appliance that cannot get enough of it produces carbon monoxide. BS 5440-2 is the British Standard that turns that fact into numbers: how much free area, where, for which appliance type, and what counts as a vent. It sits alongside BS 5440-1 (flues and chimneys) under the umbrella of the Gas Safety (Installation and Use) Regulations 1998 and is referenced by Approved Document J of the Building Regulations. The 2023 edition is a full revision of the 2009 standard, aligned with the current Approved Documents F and J and extended to cover hydrogen-ready and hydrogen-only appliances; the familiar sizing figures carry over, with added notes requiring compartments holding more than one appliance to be sized on the combined maximum heat input.
Most domestic ventilation questions now arise in three situations: an older open-flued boiler, fire or water heater that someone wants to keep; a modern room-sealed boiler going into a cupboard or loft; and a flueless cooker in a small kitchen or a new open-plan layout. Each has a different rule and a different common mistake. Open-flued appliances are undersized on ventilation because the 7 kW "free" allowance is misread as applying per appliance in a shared room. Room-sealed boilers in cupboards are fitted without checking whether the manufacturer permits enclosed installation without cooling vents. Cookers are fitted in kitchens where the only "window" is a fixed pane.
This article sets out the sizing rules, how to measure free area and room volume, the compartment rules, what counts as a vent, the interaction with extract fans, and how the figures relate to Approved Document J. For the distinction between appliance types see room sealed vs open flue appliances; for fires specifically see flueless and flue gas fire requirements.
Key Facts
- Current edition — BS 5440-2:2023, Chimneys, flue pipes and ventilation for gas appliances of rated input not exceeding 70 kW net (1st, 2nd and 3rd family gases). Part 2: Installation and maintenance of ventilation provision for gas appliances. Supersedes BS 5440-2:2009, withdrawn.
- Net input — all sizing in BS 5440-2 uses net heat input. Older data plates and literature quote gross; for natural gas, net is approximately gross divided by 1.11 (a 30 kW gross boiler is about 27 kW net).
- Room-sealed — no purpose-provided ventilation for combustion. Cooling ventilation applies only in compartments and only where the manufacturer requires it.
- Open-flued in a room — 5 cm² per kW net above 7 kW. Below 7 kW net, adventitious ventilation (assumed at 35 cm²) is sufficient in a normal room.
- Open-flued in a compartment — vents at high and low level: to a room, 10 cm²/kW high and 20 cm²/kW low; to outside, 5 cm²/kW high and 10 cm²/kW low.
- Room-sealed in a compartment — cooling vents: to a room, 10 cm²/kW high and 10 cm²/kW low; to outside, 5 cm²/kW high and 5 cm²/kW low. Omitted where the manufacturer's instructions permit enclosed installation with stated clearances.
- Multiple appliances in one compartment — size on the combined total maximum heat input (note added in the 2023 edition).
- Flueless cooker — room under 5 m³: 100 cm² permanent vent; 5 to 10 m³: 50 cm² (not required if the room has a door opening directly to outside); over 10 m³: no permanent vent. In all cases an openable window, or equivalent opening direct to outside, is required.
- Flueless instantaneous water heater (up to 11 kW net) — not permitted in a room under 5 m³; 5 to 10 m³: 100 cm²; 10 to 20 m³: 50 cm²; over 20 m³: no permanent vent; openable window required; never in a bathroom or shower room (Regulation 30 of the 1998 Regulations).
- Decorative fuel-effect fire — 100 cm² permanent ventilation regardless of input (BS 5871-3). Inset live-fuel-effect fires are treated as open-flued.
- Vent construction — permanent, not closable, not fitted with a fly screen that reduces free area; apertures no smaller than 5 mm (so they cannot block) and no larger than 10 mm (vermin); free area marked by the manufacturer or calculated from the aperture dimensions, not the overall grille size.
- Vent position — direct to outside, or to an adjoining room that itself has a vent to outside of at least the same free area. Not into a garage, bathroom, bedroom used as sleeping accommodation (for open-flued appliances) or an unventilated roof space. Not within the flue terminal exclusion distances in BS 5440-1.
- Extract fans — any extract fan (kitchen, bathroom, tumble dryer, cooker hood) in the same or an interconnected room as an open-flued appliance requires a spillage test with all fans running and doors and windows closed (BS 5440-1). A failed spillage test is an At Risk situation under the Gas Industry Unsafe Situations Procedure.
- Approved Document J (2010 edition incorporating 2010 and 2013 amendments, with 2022 amendments) — Section 3 refers gas appliance ventilation to BS 5440-2 and gives the same 5 cm²/kW figure for open-flued appliances.
Quick Reference Table
Need to quote gas work? squote generates accurate, professional quotes fast.
Try squote free →| Appliance type | Location | Permanent free area required |
|---|---|---|
| Room-sealed (any input) | Room | None |
| Room-sealed | Compartment, vents to room | 10 cm²/kW high + 10 cm²/kW low (unless manufacturer permits none) |
| Room-sealed | Compartment, vents to outside | 5 cm²/kW high + 5 cm²/kW low (unless manufacturer permits none) |
| Open-flued, up to 7 kW net | Room | None (adventitious) |
| Open-flued, over 7 kW net | Room | 5 cm² × (kW net − 7) |
| Open-flued | Compartment, vents to room | 10 cm²/kW high + 20 cm²/kW low |
| Open-flued | Compartment, vents to outside | 5 cm²/kW high + 10 cm²/kW low |
| Decorative fuel-effect fire | Room | 100 cm² |
| Flueless cooker | Room under 5 m³ | 100 cm² + openable window |
| Flueless cooker | Room 5–10 m³ | 50 cm² + openable window (vent not needed if door direct to outside) |
| Flueless cooker | Room over 10 m³ | Openable window only |
| Flueless instantaneous water heater ≤11 kW | Room 5–10 m³ | 100 cm² + openable window |
| Flueless instantaneous water heater ≤11 kW | Room 10–20 m³ | 50 cm² + openable window |
| Flueless instantaneous water heater ≤11 kW | Room over 20 m³ | Openable window only |
Worked example: a 28 kW net open-flued boiler in a kitchen needs (28 − 7) × 5 = 105 cm². The same boiler in an under-stairs cupboard vented to the hall needs 280 cm² high and 560 cm² low. In practice that cupboard is a candidate for a room-sealed replacement.
Detailed Guidance
Why 7 kW is "free"
BS 5440-2 assumes a normally constructed room admits about 35 cm² of adventitious air through gaps around doors, windows and floors. At 5 cm² per kW that covers 7 kW of open-flued input, so the formula only starts above 7 kW. The allowance applies once per room, not once per appliance: two 6 kW open-flued appliances in one room total 12 kW and need (12 − 7) × 5 = 25 cm². Modern airtight dwellings with draught-stripped doors and sealed floors have less adventitious ventilation than the standard assumes, which is one reason open-flued appliances are increasingly difficult to justify in refurbished homes and why Approved Document F's airtightness targets push toward room-sealed appliances.
Measuring free area
Free area is the total open aperture of the vent, not the size of the grille. Manufacturers mark free area on the product; where it is not marked, measure the apertures and sum them. A standard 229 × 76 mm (9 × 3 inch) clay air brick provides roughly 50 to 65 cm² depending on pattern; a 229 × 229 mm (9 × 9 inch) air brick about 140 to 180 cm². Plastic louvred vents often quote 30 to 50 % of face area. Fly screens, baffles and bent louvres all reduce free area and must be accounted for. Where a vent runs through a cavity wall it must be ducted across the cavity (a sleeve or a cavity liner) so that the free area is maintained and the cavity is not used as the air path.
Measuring room volume
For flueless appliances, room volume is length × width × height of the room the appliance is in. Where two rooms are permanently open to each other (an archway with no door, an open-plan kitchen-diner) they are treated as one room. A doorway with a door is a separate room, even if the door is normally left open. Fitted units do not reduce the volume for this purpose. The purpose of the minimum volume is dilution of combustion products, so a cooker in a 4.5 m³ utility room needs the 100 cm² vent even though the door next to it opens into a large kitchen.
Compartments: when vents are needed and when they are not
A compartment is an enclosure specifically designed or adapted to house a gas appliance: a boiler cupboard, an airing cupboard, a purpose-built housing. An appliance in a compartment that is not sealed from the room behind louvred doors is still in a compartment. The compartment rules exist for two reasons: an open-flued appliance in a compartment needs its combustion air delivered to it, and any appliance generates heat that must be removed so that the appliance and its controls do not overheat.
For room-sealed boilers the manufacturer's installation instructions override the default. Most current condensing boilers are certified for installation in a compartment with no cooling vents provided the stated clearances are kept (typically 5 mm at the sides, 100 to 300 mm below and a stated clearance above the flue connection). Where the instructions say that, no vents are needed and the compartment door can be solid. Where the instructions require ventilation, or the boiler is an older model whose instructions do not address compartments, apply the 10/10 or 5/5 cm²/kW cooling vents.
For an open-flued appliance in a compartment the vents are always required, high and low, sized on the full net input (not minus 7 kW). High vents are placed as near the top of the compartment as practicable and low vents as near the bottom. If the compartment also contains a cylinder, the airing-cupboard rule applies: the appliance must be separated from stored clothes by a non-combustible perforated partition with no perforation larger than 13 mm, and the partition must not restrict the required vent areas. Compartments should carry a notice stating that the vents must not be blocked and that the compartment must not be used for storage.
Vents through adjoining rooms, roof spaces and garages
Where the appliance room has no external wall, the vent may be taken to an adjoining room that itself has a vent to outside, and both vents must have at least the required free area. The chain cannot pass through a garage (petrol vapour), a bathroom or shower room, or a bedroom used as sleeping accommodation where the appliance is open-flued. A roof space may be used as the air source only if it is itself ventilated to outside by at least the required area through eaves or tile vents. Ventilation via a cellar or basement for LPG (3rd family) appliances has additional low-level requirements because LPG is heavier than air; see lpg installations.
Extract fans and spillage
Extract fans in the same room as an open-flued appliance, or in a room connected to it by doors, depressurise the room and can reverse the flue. BS 5440-1 requires a spillage test on the appliance with every fan in the dwelling running (including cooker hoods, bathroom fans and tumble dryers) and all external doors and windows closed. If spillage occurs, the options are additional purpose-provided ventilation, interlocking the fan with the appliance, or replacing the appliance with a room-sealed one. Approved Document J and Approved Document F both flag this interaction; a new kitchen extract installed next to an existing open-flued boiler is a common trigger for a failed test months later. See unsafe situations for how a failed spillage test is classified.
Recording and labelling
Ventilation provision is checked and recorded on every Gas Safety Record and at every service: appliance type, net input, required free area, provided free area and condition of the vents. Blocked, painted-over or deliberately covered vents are a recurring finding and are classed under the Unsafe Situations Procedure according to the appliance type and the test results. Where a customer has blocked a vent "because of the draught", the fix is education and sometimes a different vent location, never leaving it blocked.
Frequently Asked Questions
Does a modern combi boiler in a kitchen cupboard need vents in the cupboard door?
Usually not, but only because the manufacturer's installation instructions for most current condensing boilers permit enclosed installation with stated clearances. Check the instructions for the exact model. If they are silent or require ventilation, fit cooling vents of 10 cm²/kW at high and low level to the room (or 5 cm²/kW to outside), and leave the clearances the instructions give.
How much ventilation does an open-flued back boiler need?
5 cm² per kW of net input above 7 kW, in the room the appliance draws its air from. A 13 kW net back boiler and fire unit needs 30 cm². If the unit is behind a fire surround in a living room with a kitchen extractor fan through an open serving hatch, a spillage test with the fan running is also required.
Can I use a trickle vent in a window as the permanent vent?
No. Trickle vents are closable and their free area is small and unmarked. BS 5440-2 requires a permanent, non-closable vent of marked or calculated free area. Window trickle vents can count toward Approved Document F background ventilation but not toward BS 5440-2 combustion air.
My customer's kitchen has a fixed window and a gas cooker. Is that allowed?
A flueless cooker requires an openable window or equivalent opening direct to outside in every case, in addition to any permanent vent required by room volume. A fixed pane does not satisfy this. An external door in the same room does, as does a working extract fan ducted to outside in some interpretations, but the standard's wording is an openable window or equivalent; where in doubt, provide an openable light.
Is BS 5440-2 the same as Approved Document J?
No. Approved Document J is statutory guidance under the Building Regulations and refers gas appliance ventilation to BS 5440-2; the standard contains the detailed tables. Complying with BS 5440-2 is the normal way of showing compliance with Requirement J2 (air supply). Scotland and Northern Ireland reference the standard through their own technical handbooks and regulations.
Regulations & Standards
Gas Safety (Installation and Use) Regulations 1998 — Regulation 27 (flues and air supply), Regulation 30 (room-sealed appliances in bathrooms and sleeping accommodation), Regulation 3 (competence and Gas Safe registration).
BS 5440-2:2023 — installation and maintenance of ventilation provision for gas appliances up to 70 kW net.
BS 5440-1:2008 — flueing of gas appliances; spillage testing; terminal positions.
BS 5871-1:2005, BS 5871-2:2005 and BS 5871-3:2005 — gas fires, convectors, fire/back boiler units and decorative fuel-effect appliances.
BS 6172:2010+A1:2017 — installation of domestic gas cooking appliances.
BS 6798:2014 — installation of gas-fired boilers up to 70 kW net; compartments and clearances.
Building Regulations 2010, Approved Document J — combustion appliances and fuel storage; Requirement J2 air supply.
Building Regulations 2010, Approved Document F Volume 1 (2021 edition) — ventilation and the interaction with combustion appliances.
Gas Industry Unsafe Situations Procedure (IGEM/G/11) — classification of inadequate ventilation and spillage.
BSI Knowledge: BS 5440-2:2023 — current edition and supersession of BS 5440-2:2009.
Gas Safe Register: Technical information for engineers — technical bulletins on ventilation and spillage.
IGEM: BS 5440 update training — overview of the 2023 revisions.
room sealed vs open flue appliances — the appliance types and why room-sealed needs no room vent.
flueless and flue gas fire requirements — fires: room volumes, DFE 100 cm² rule and spillage.
flue clearances and part j — BS 5440-1 terminal positions and the vent exclusion zones.
boiler siting and location rules — where a boiler may go: bedrooms, bathrooms, cupboards, lofts and garages.
unsafe situations — how blocked vents and failed spillage tests are classified.
carbon monoxide — the consequence of inadequate air supply.
lpg installations — additional ventilation rules for LPG below ground level.