Summary
"There's a smell of drains" is a call that plumbers, drainage engineers and housing maintenance teams get every week, and it is one of the few faults where the diagnosis is almost entirely about where the air is coming from rather than what is blocked. Drains always contain foul air. The building's defence against it is a water seal at every connection to the system (the trap under each appliance, the seal in the WC pan, the water in a gully), plus a vented stack that lets the pressure changes caused by discharging water escape through the roof instead of through the traps. When the smell is indoors, one of those seals has failed or one of those vents is in the wrong place.
The common causes are mundane. A spare-room basin or an ensuite shower that nobody uses for a month evaporates its seal, especially over a warm summer or with underfloor heating. A floor gully in a utility room dries out. A long waste run siphons the bath trap every time the bath empties. A plastic air admittance valve on top of a boxed-in stub stack perishes and sticks open. A WC pan connector perishes and lets air (and, eventually, water) out behind the pan. A washing machine is connected to a standpipe with no trap. The less common causes are the ones that take longer and cost more: a cracked clay drain under a suspended timber floor, a stack vent that was cut short when the roof was done, an interceptor trap in the chamber that has lost its water, a disused drain branch capped badly or not at all.
This guide works through the diagnosis in order of likelihood and cost, with the tests that confirm each one (water into traps, a smoke test, a dye test, a CCTV survey) and the fix. It covers the regulations that set the trap seal depths and the stack termination position, and when the smell is not drains at all. For the specific case of a smell with no visible damp see damp smell no visible damp; for septic systems see septic tank smell diagnosis; and if there is any suspicion the smell is gas rather than drains, stop and read gas smell first.
Key Facts
- Trap seals (Approved Document H1, Table 1) — basin and bidet 75 mm; bath and shower 50 mm; sink, washing machine and dishwasher 75 mm; WC pan 50 mm. A seal of less than 25 mm under working conditions is a failure
- Evaporation — a 75 mm basin seal in a warm, dry room can evaporate in 3–6 weeks of disuse; a 50 mm shower trap faster; a floor gully in a boiler room or utility faster still
- Siphonage — a waste run longer or steeper than Approved Document H1 Table 2 allows (32 mm: 1.7 m; 40 mm: 3.0 m; 50 mm: 4.0 m) pulls the seal out of the trap as the appliance empties; induced siphonage pulls one trap when a neighbouring appliance discharges into the same branch
- Air admittance valves — BS EN 12380 valves let air in but not out; they fail stuck open (smell) or stuck shut (gurgling and slow drains); life 10–20 years; must be accessible and above the flood level of the highest appliance
- Stack vent termination — Approved Document H1 requires an open stack vent to finish at least 900 mm above the top of any opening window or ventilator within 3 m, with a durable cage or cover; a vent that was shortened or terminated under the eaves blows sewer air into the bedroom
- Pan connectors — rubber or polypropylene WC pan connectors perish and lose their seal against the pan spigot or the pipe; a smell from behind the WC with no visible leak is often this
- Washing machine and dishwasher hoses — must discharge through a trapped standpipe or a trap spigot; a hose pushed into an untrapped pipe is an open drain in the kitchen
- Gullies — an outside trapped gully taking the kitchen waste must hold water; a dry, blocked or cracked gully lets drain air back up the sink waste, and a kitchen smell that comes and goes with the weather often has this cause
- Interceptor traps — many pre-1950 houses have an interceptor (disconnecting) trap in the last chamber before the sewer; if its water seal is lost through a cracked body or a missing rodding-eye stopper, sewer air enters the house drain and every weak seal indoors
- Broken drains under floors — a cracked or displaced clay drain under a suspended floor vents sewer air into the void and up through gaps in the boards, usually with a damp or musty component; confirm by CCTV or smoke test
- Sewer gas — hydrogen sulphide (rotten eggs, toxic at concentrations above about 10 ppm, odour fatigue at higher levels), methane (odourless, explosive at 5–15% in air), ammonia; never enter a chamber (Confined Spaces Regulations 1997) and never use a flame to find a smell
- Smoke test — a drainage smoke machine or smoke pellets introduced at a chamber or a vent, with every trap charged, shows smoke at the failed seal, open pipe or crack within minutes; the quickest way to find a hidden fault
- Dye and water test — fill a suspected trap with dyed water and check it after 24 hours and after neighbouring appliances have been used; a lost or lowered seal confirms siphonage or a leaking trap
- Not drains — a sulphur smell from a hot water cylinder (bacteria in a cold cylinder), a dead rodent under a floor, mould behind a unit, a failed condensate trap on a boiler, and the smell of a new PVC floor or an oil-based paint are all reported as "drains"; and a gas smell is always treated as gas first
- Pricing (2026) — diagnostic visit with trap checks and seal top-up £70–£130; smoke test £120–£250; AAV replacement £60–£120; pan connector replacement £90–£180; stack vent extension and cage £150–£350 plus access; interceptor stopper or re-seal £150–£400; CCTV survey £150–£350; under-floor drain repair from £600–£1,500 per metre
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Where the smell is | When it is worst | Most likely cause | Test | Fix |
|---|---|---|---|---|
| Spare bathroom or ensuite, little used | After a dry warm spell or a holiday | Evaporated trap seal | Run the taps; smell goes within minutes | Top up weekly; trap seal primer or deeper trap; use the room |
| Main bathroom, after the bath empties | Immediately after use | Bath trap siphoned (run too long/flat) | Check seal depth after emptying | Re-run or upsize waste; anti-siphon trap; AAV |
| Behind or around the WC | Constant, worse in warm weather | Perished pan connector or pan-to-floor seal | Smoke test; look for staining | Replace pan connector; re-seat pan |
| Boxed-in stack or airing cupboard | Constant | Failed AAV, open or cracked stack joint, capped branch leaking | Remove AAV and inspect; smoke test | Replace AAV; remake joint; cap properly |
| Kitchen, by the sink | When windy or raining | Dry or blocked outside gully; untrapped appliance hose | Pour water into gully; check hose connection | Clear gully; fit trap or standpipe |
| Upstairs bedroom with open window | Windy days, when WC flushed | Stack vent terminates too low or near the window | Look at the vent position | Extend vent to 900 mm above opening; cowl |
| Whole ground floor, musty plus drains | Constant, worse in warm weather | Broken drain under floor; dry interceptor | Smoke test; CCTV; check interceptor seal | Repair drain; re-seal interceptor |
| Utility or plant room floor | Constant | Dry floor gully or untrapped condensate connection | Pour water into gully | Keep charged; trap primer; trap the condensate |
| Everywhere, only when a particular appliance is used | On discharge | Induced siphonage on shared branch; blocked vent | Dye test traps; check stack vent cage | Vent branch; clear vent; AAV |
| Whole house, intermittent, "rotten eggs" | Any time | Sewer surcharge pushing air through weak seals; or NOT drains (gas, cylinder) | Rule out gas first; check external chambers | Report sewer to undertaker; fix weak seals |
Detailed Guidance
Step 0 — rule out gas
A smell described as "eggy", "sulphury" or "rotten" may be natural gas (which is odorised with a sulphur compound precisely so it smells like this) rather than drains. If there is any doubt, treat it as gas: no flames, no switches, windows open, call the National Gas Emergency Service on 0800 111 999 and follow gas smell. Drain diagnosis waits until gas is excluded.
Step 1 — localise the smell
Walk the house with the customer and find the room where it is strongest and the times it is worst. Three questions narrow it down quickly: Is it one room or everywhere? Is it constant or does it come after an appliance is used, in windy weather, or after a dry spell? Is there any appliance or floor gully in that room that is rarely used? Write down the answers; they usually give the cause before any tool comes out.
Smell strongest where?
├─ One bathroom / ensuite / utility
│ ├─ Appliance rarely used? ───────────────► Dry trap: run water, re-test
│ ├─ Worse just after bath/shower empties? ─► Siphoned trap: check run, add vent/anti-siphon
│ ├─ Behind WC? ──────────────────────────► Pan connector / pan seal: smoke test, replace
│ └─ Boxed-in pipework present? ──────────► AAV or joint: open up, inspect, smoke test
├─ Kitchen
│ ├─ Outside gully dry or full? ──────────► Gully: clear, charge, repair
│ └─ Appliance hose into pipe? ───────────► Untrapped connection: fit trap/standpipe
├─ Upstairs, worse with window open / wind ─► Stack vent position: extend / cowl
└─ Whole ground floor, musty component ────► Under-floor drain / interceptor: smoke test, CCTV
Step 2 — charge every trap
Run every tap, shower and bath for thirty seconds, flush every WC, and pour a bucket of water into every floor gully, shower waste and outside gully. If the smell fades over the next hour, the cause was a dry seal and you have found it; the only remaining question is why it dried. A seal that dries through disuse needs a routine (run the tap weekly), a deeper trap, or a trap seal primer. A seal that keeps disappearing in a room that is used every day is being siphoned, and the pipework is the fault.
Check seal depth where you can see it: after the appliance has fully emptied, the water in a basin trap should sit at the full 75 mm; a seal visibly lower, or a gurgle at the end of draining, means siphonage. Measure the run to the stack against the Approved Document H1 Table 2 limits (32 mm: 1.7 m; 40 mm: 3.0 m; 50 mm: 4.0 m, at 18–90 mm per metre). Fixes are to upsize, to fit an air admittance valve or branch vent at the head of the run, or to fit an anti-siphon trap. See waste pipes.
Step 3 — air admittance valves and boxed-in pipework
An AAV is a spring- or membrane-operated one-way valve that lets air into the stack when a discharge creates negative pressure, and closes under positive pressure to keep sewer air in. Most are plastic and most are hidden in boxing or a loft. They fail in two ways: stuck shut (slow drains and gurgling) or stuck open, perished or cracked (smell). Find it, remove it, and look: a membrane that is distorted, cracked or fouled is replaced (£15–£40 for the valve) and the job is done. Make sure the replacement is to BS EN 12380, sits at least 200 mm above the flood level of the highest connected appliance (the manufacturer's installation height applies), and remains accessible. A stack with an AAV cannot serve as the only vent for the drain: Approved Document H1 requires the drain to be ventilated by at least one open stack vent at the head of each drain run, so if a previous installer capped the only open vent with an AAV, drain air has nowhere to go but the weakest trap.
While the boxing is open, look at every joint: a soil stack solvent joint that was never fully home, a push-fit ring seal that has slipped, a capped-off branch from a removed appliance with a loose cap or a rag stuffed in it. Any of these is an open drain in the house.
Step 4 — the WC
A WC smell with no visible water is usually the pan connector. Flexible connectors in particular perish, crack along the corrugations and lose their grip on the pan spigot. Smoke will come out around the base of the pan or behind it. Replace with a rigid or flexible connector of the correct offset, with the spigot clean and the seal lubricated; check that the pan is firmly fixed so it cannot rock the joint open. A pan sealed to the floor with silicone all round can hide a leak that is rotting the floor beneath; leave a gap at the back.
Step 5 — the kitchen
Kitchen smells divide into the gully and the appliance connections. Go outside and look at the gully the sink discharges into. If it is dry, the trap has evaporated or the gully body is cracked below the water line; charge it and see if it holds. If it is full and stagnant, the drain beyond is blocked and the sink is draining into a sump of stale water that breathes back up the waste pipe with every change in pressure; clear the drain. If the kitchen waste runs into a hopper or an untrapped pipe (common on older houses where a rainwater hopper was pressed into service), there is no seal at all and the fix is a trapped gully or a trap on the sink waste with a proper connection. See gully types and installation and back inlet gully vs hopper.
Inside, check how the washing machine and dishwasher connect. A hose pushed into a bare pipe, or into a standpipe with no trap, is an open drain. Fit a trapped standpipe (40 mm, minimum 600 mm high) or connect to the spigot of the sink trap, with the hose in a high loop. See kitchen waste and supply connections.
Step 6 — the stack vent
A smell in an upstairs room, worst with the window open and in certain winds, points to the stack terminal. Approved Document H1 requires an open vent to terminate at least 900 mm above the top of any opening (window, rooflight, ventilator) within 3 m horizontally, finished with a cage or perforated cover that keeps birds out without restricting the air. Vents cut short during a re-roof, terminated in the loft, or finished just under the eaves beside a bedroom window are a regular find. Extend the pipe, re-position or fit a cowl; a cowl alone does not fix a vent that is at window height.
Step 7 — under the floor and in the chambers
If the whole ground floor smells, the smell has a musty or damp edge, and the traps all hold water, suspect the drain itself. On a suspended timber floor, a cracked or displaced clay drain or a disused branch left open under the floor vents sewer air into the void and the smell comes up through the boards and skirtings. Lift the external chamber covers: standing water in a chamber, flow backing up, or an interceptor trap whose rodding-eye stopper is missing or whose body has cracked below the water line all let sewer air into the house drain. A dry interceptor is a classic cause of a whole-house smell on pre-war housing, and the fix (a new stopper, or re-sealing or removing the interceptor) is cheap once found.
Confirm with a smoke test before anyone digs. With every trap charged, introduce smoke at a chamber or the stack base with the vent temporarily sealed; smoke appearing indoors marks the failed seal, the broken pipe or the open branch. Follow with a CCTV survey of the suspect run to locate and grade the defect (drain cctv survey), then repair by patch liner, excavation or re-laying as the survey dictates (foul drainage repair).
When it is not the drains
Sulphur smells from hot water taps only come from a cylinder running cool (bacteria producing hydrogen sulphide); the fix is to run the cylinder at 60 °C and chlorinate if needed. A smell under a kitchen unit with no drain connection is more often a dead rodent, a leaking appliance or mould than drains. A boiler condensate pipe discharging into an untrapped waste or an internal gully without a trap can smell of drains in the boiler cupboard; it needs its own trap or a trapped connection. Sewer surcharge in the street (heavy rain, a blocked public sewer) pushes air through every marginal seal in the house at once, and then the smell is everywhere for an hour and gone; report it to the sewerage undertaker.
Frequently Asked Questions
The smell comes and goes. Does that mean it is not the drains?
No. Intermittent drain smells are the norm, because the pressure in the system changes with every discharge and with the weather. Wind over a low stack terminal, heavy rain surcharging the sewer, a bath emptying and siphoning a trap, or a gully drying between uses all produce a smell that lasts minutes to hours and then clears. Note when it happens; the timing usually points to the cause.
Is sewer gas dangerous in a house?
In the concentrations that cause a smell in a room it is unpleasant rather than acutely dangerous, but it should never be tolerated: hydrogen sulphide is toxic, methane is explosive in a confined void, and a smell indicates an open path from the sewer that can also admit vermin and, in a surcharge, sewage. Never lean into a chamber or enter one to find a smell (Confined Spaces Regulations 1997), never test with a flame, and ventilate the room while you work.
Can I just fit an air admittance valve to stop the smell?
Only if the smell is caused by siphonage on a branch that needs venting. An AAV lets air in to stop traps being pulled; it does not let air out, so it does nothing for a dry trap, a perished pan connector or a cracked pipe. And an AAV must never replace the one open vent that each drain run needs under Approved Document H1; sealing a vented stack with an AAV is a common cause of exactly the smell you are trying to cure.
Why does the smell appear after a holiday?
Because unused traps evaporate. A basin's 75 mm seal in a warm house can be gone in a month; a shower's 50 mm seal sooner. The first flush and tap-run on return usually ends it. If a room is permanently unused, fit a deeper trap, a trap seal primer, or ask the customer to run the taps weekly; adding a cup of cooking oil to a floor gully slows evaporation but fouls the trap and is not recommended.
What does it cost to find a drain smell?
A diagnostic visit that checks and charges every trap and inspects the accessible pipework is £70–£130. If that does not find it, a smoke test (£120–£250) nearly always does, and a CCTV survey (£150–£350) locates any drain defect the smoke test points to. The repairs range from a £60–£120 AAV or a £90–£180 pan connector to several hundred pounds for a stack vent extension or interceptor work, and £600–£1,500 per metre for an under-floor drain repair.
Regulations & Standards
Building Regulations 2010, Approved Document H, Section H1 (Foul water drainage) — trap seal depths (Table 1), maximum unventilated branch lengths (Table 2), ventilation of discharge stacks and drains, stack vent termination 900 mm above openings within 3 m, air admittance valve requirements, access for maintenance
BS EN 12056-2:2000 — Gravity drainage systems inside buildings: sanitary pipework, layout and calculation, including ventilation of branches and stacks
BS EN 12380:2002 — Air admittance valves for drainage systems: requirements, test methods and evaluation of conformity
BS EN 752:2017 — Drain and sewer systems outside buildings: sewer system management
BS EN 13508-2:2003+A1:2011 — Visual inspection coding of drains and sewers (CCTV survey reporting)
Confined Spaces Regulations 1997 (SI 1997/1713) — entry into chambers and manholes
Gas Safety (Installation and Use) Regulations 1998 — the gas-smell procedure that takes priority over drain diagnosis
Housing Act 2004 (Housing Health and Safety Rating System) — drainage and sanitation hazards in rented housing
Environmental Protection Act 1990, Part III — statutory nuisance from defective drains
Water Industry Act 1991 — sewerage undertaker's responsibility for public sewers and shared drains (since 1 October 2011)
Approved Document H: Drainage and waste disposal — GOV.UK — trap seals, branch ventilation and stack terminations
HSE: Confined spaces — hazards of sewer gases and entry into chambers
National Gas Emergency Service — Cadent — what to do if the smell could be gas (0800 111 999)
Water UK: Sewer responsibility — who is responsible for which drain
Shelter: Repairs to drains and sewers — tenant and landlord obligations for drainage defects
gurgling drains diagnosis — the companion fault: air moving the other way through the seals
sink or bath draining slowly — the slow-draining appliance that often shares the cause
damp smell no visible damp — when the smell is musty rather than drains
septic tank smell diagnosis — smells on properties with septic tanks or treatment plants
gas smell — the procedure that must come first if gas is possible
waste pipes — trap seals, branch lengths and ventilation rules
gully types and installation — gully traps and the kitchen smell
drain cctv survey — locating an under-floor defect once a smoke test points to it