Summary
A slow-draining basin, bath or kitchen sink is one of the most common plumbing call-outs and one of the easiest to misdiagnose expensively. The customer has often already poured two bottles of drain cleaner down it, which tells you two things: the blockage is not soluble, and you are now dealing with a caustic residue in the trap. The job is to work out, in the first five minutes, whether the fault is in the appliance's own waste (trap, flexible connector, branch pipe, pop-up mechanism) or further down the system, because the first is a half-hour fix at the sink and the second is a drainage job that needs the stack or the gully opened up.
The decisive test is simple. If the slow appliance is the only one affected, and running water elsewhere does not make it worse or cause it to back up, the fault is local. If two or more appliances are slow, or using the bath makes the basin gurgle, or the lowest appliance fills when another discharges, the fault is in the shared pipework or the drain. Most of this guide is about the local fault; the last section covers how to tell when it is not.
The local causes divide into blockages and design. Blockages are hair, soap, toothpaste and skin in basin and bath traps; fat, food and coffee grounds in kitchen traps; limescale narrowing in hard-water areas; and small objects (bottle caps, razor covers, a child's toy) sitting in the trap bend. Design faults are the corrugated flexible waste connector that has been bent into a sag, a branch pipe run flat or uphill, a run that exceeds the Approved Document H1 unventilated lengths so that it is permanently part-full, a bottle trap with a restricted outlet feeding a long run, and a basin waste fitting whose pop-up plug or slotted grid is itself the restriction. A fault that returns every few months is almost always design, not dirt.
Key Facts
- Local versus system — one appliance slow, others normal, no backing-up when others run = local fault (trap or branch). Two or more slow, gurgling, or back-up = stack, drain or vent fault: see gurgling drains diagnosis
- Trap sizes and seals (Approved Document H1, Table 1) — washbasin and bidet 32 mm trap with 75 mm seal; bath and shower 40 mm trap with 50 mm seal; kitchen sink, washing machine and dishwasher 40 mm trap with 75 mm seal
- Maximum unventilated branch lengths (Approved Document H1, Table 2) — 32 mm: 1.7 m; 40 mm: 3.0 m; 50 mm: 4.0 m; all at gradients of 18–90 mm per metre
- Fall — 18–90 mm per metre (roughly 1:55 to 1:11). A flat or back-falling branch holds water and silt and will keep blocking
- Bends — each sharp 90° elbow in a small-bore waste is worth about 0.3–0.5 m of pipe length in resistance; use swept bends or two 45° bends
- Flexible wastes — corrugated flexible connectors collect debris in every rib, sag between fixings, and are the single most common cause of a basin that keeps blocking. Replace with rigid solvent-weld or push-fit pipe
- Bottle traps — compact and easy to clean but have a smaller free passage and a higher resistance than a P- or S-trap; avoid where the run is long or the appliance is a kitchen sink
- Hair and soap — the basin and bath blockage; a soft black-grey plug in the trap bend or around the pop-up plug linkage. Fat and food — the kitchen blockage; a solid pale plug in the trap and the first metre of pipe where it cools
- Pop-up wastes — the plug mechanism and the linkage rod restrict the waste outlet by design and collect hair; a slotted basin waste with a clicker or a flip plug clears much better
- Overflow — a basin or bath overflow that is itself blocked makes a slow drain look worse because air cannot enter the trap arm; check the overflow runs clear
- Air admittance valves — a stuck AAV (BS EN 12380) on a branch makes a long run drain slowly and gurgle; test by removing it and running the appliance
- Chemicals — sodium hydroxide (caustic soda) based cleaners generate heat, soften old ABS and perish rubber seals; sulphuric acid products are more dangerous still. Mechanical clearance first; enzymatic or bacterial treatments for maintenance
- Dishwashers and washing machines on the same trap — a kitchen sink with an appliance spigot on its trap can be slowed by a part-blocked spigot or a drain hose without a high loop or standpipe; check both
- Pricing (2026) — trap clean and refit £60–£110; replace flexible waste with rigid pipe £90–£160; re-run a branch at correct fall £150–£350; replace a basin waste and trap £110–£200; bath waste and trap replacement with bath panel off £150–£280
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Symptom | Likely cause | Where to look | Fix |
|---|---|---|---|
| Basin drains slowly, gurgles at the end, others fine | Hair and soap in trap or around pop-up linkage | Trap bend, waste outlet, pop-up rod | Remove and clean trap; clean or replace waste |
| Basin fine when first fitted, slow again every few months | Corrugated flexible waste sagging and silting | Under the basin | Replace with rigid 32 mm pipe at correct fall |
| Bath drains slowly, water sits in the bottom | Hair in bath trap; flat or long 40 mm run; shallow trap silted | Bath trap via panel or access hatch | Clean trap; check run length and fall; replace trap |
| Kitchen sink slow, worse after washing-up | Fat and food plug in trap and first metre of pipe | Trap, pipe to outside gully | Dismantle and clear; flush; advise against fat down the sink |
| Kitchen sink slow only when dishwasher runs | Blocked appliance spigot or drain hose; no high loop | Trap spigot, dishwasher hose | Clear spigot; fit high loop or standpipe |
| Slow drain and a smell of drains | Trap seal lost or part-lost by siphonage; long run | Check seal depth after draining | Re-run at correct fall; add AAV or vent |
| Slow drain and overflow does not take water | Blocked overflow (basin or bath) | Overflow channel and tube | Clear overflow; replace bath overflow kit if perished |
| Shower tray drains slowly | Hair in the shallow 50 mm seal trap; 40 mm run too flat | Trap via removable grate | Clean trap; check fall under tray |
| Slow drain, water rises when another appliance is used | Downstream blockage in stack or drain | Stack, gully, inspection chamber | Not local: see blocked-drain diagnosis |
| Slow drain after new bathroom fitted | Run too long for 32 mm; too many bends; bottle trap on long run | Pipework route | Upsize to 40 mm or add vent / AAV; replace trap |
Detailed Guidance
Step 1 — confirm it is local
Fill the slow appliance and time it, then run every other appliance that shares the same stack or drain. Note whether:
- any other appliance is slow (system fault)
- the slow appliance gurgles or its water level moves when another is used (shared pipe or vent fault)
- the lowest appliance in the house, or an outside gully, backs up or overflows (drain blockage)
If none of those, the fault is in the appliance's own waste. If any of them, stop and move to the stack and drain: gurgling drains diagnosis and blocked drain diagnosis.
Only one appliance slow?
├─ No, two or more ──────────────► Stack / drain / vent fault (not this guide)
└─ Yes
├─ Water rises or gurgles when another appliance runs?
│ ├─ Yes ────────────────────► Shared branch or vent fault (check AAV, stack)
│ └─ No
│ ├─ Overflow takes water?
│ │ └─ No ──────────────► Clear overflow, then re-test
│ ├─ Remove trap: blocked?
│ │ ├─ Yes ────────────► Clean / replace trap; check waste fitting
│ │ └─ No
│ │ ├─ Flexible corrugated waste? ─► Replace with rigid pipe
│ │ ├─ Fall < 18 mm/m or back-fall? ─► Re-run branch
│ │ ├─ Run longer than Table 2? ────► Upsize / vent / AAV
│ │ └─ All fine ────────────────────► Blockage in branch: rod / snake from trap end
Step 2 — the overflow
Before dismantling anything, pour water into the overflow slot of the basin or bath. If it does not run away freely, the overflow is blocked (hair and scale in a basin overflow channel; a perished or kinked bath overflow tube). A blocked overflow reduces the air path into the trap arm and makes any drain seem slower. On a bath, a failed overflow kit also leaks when the bath is over-filled, which the customer may not have connected to the slow drain.
Step 3 — the trap
Put a bowl under the trap, undo the compression nuts by hand and remove it. Basin and bath traps will be found with a plug of hair bound with soap; kitchen traps with congealed fat and food. Clean the trap, check the seal (the washers go brittle and are cheap), and look up into the waste outlet from below: hair wraps around a pop-up linkage and sits in the slots of a slotted waste where it cannot be seen from above. Clean or replace the waste fitting if it is the restriction.
While the trap is off, run a drain snake or a length of stiff cable into the branch pipe towards the stack or gully. On a kitchen branch the fat plug often sits 0.5–1.5 m along the pipe where the water has cooled, not in the trap. Flush with hot (not boiling) water once clear.
Refit and test. If the drain now runs freely, the job is done; if it was a kitchen sink, tell the customer in writing what caused it. If it is still slow with a clean trap, the fault is design or a deeper blockage.
Step 4 — the pipework
Look at what the trap connects to:
Corrugated flexible waste — replace it. A flexible connector that is anything other than a straight fall collects a ring of debris in every corrugation and sags between fixings into a permanent sump. Fit rigid 32 mm or 40 mm pipe (solvent-weld ABS or push-fit polypropylene, not mixed without the right adaptor) with swept bends and a proper fall. If the only reason the flexi was used is that the basin outlet does not line up with the pipe, use an offset or a short length of rigid pipe with two 45° bends.
Fall — hold a level on the branch. Approved Document H1 requires 18–90 mm per metre of fall. A branch run flat, or with a hump over a joist, holds standing water in which hair and fat accumulate; it will re-block every few months no matter how well you clean it. Re-clip or re-run it.
Length and size — measure from the trap outlet to the stack or gully connection. A 32 mm basin branch is limited to 1.7 m unventilated; a 40 mm bath, shower or sink branch to 3.0 m; a 50 mm branch to 4.0 m. Beyond those lengths the pipe runs part-full, the trap seal is pulled by self-siphonage, and the appliance drains slowly and gurgles. The fix is to upsize (32 mm to 40 mm doubles the permitted length to 3.0 m), to add a vent or an air admittance valve to BS EN 12380 at the head of the run, or to use an anti-siphon trap. Count the bends: more than two 90° elbows on a 32 mm run is pushing it even within the length limit.
Bottle traps on long runs — a bottle trap's outlet is smaller than a tubular trap's and its internal path is restrictive. On a basin with a short run to the stack it is fine; on a long run or a kitchen sink swap it for a tubular P-trap.
Appliance spigots — a kitchen trap with a dishwasher or washing machine spigot can be slowed by fat in the spigot or by a drain hose connected without a high loop, so that the appliance's pump pushes water back up the sink waste or the sink's water drains into the hose. Clear the spigot, fit the hose in a high loop above the trap or to a trapped standpipe (minimum 600 mm high), and check the hose is not kinked.
Step 5 — shower trays and baths with poor access
Shower traps have a shallow seal (50 mm) and a removable grate; lift it and the hair plug is usually visible and removable by hand or with a hooked tool. Check the fall of the 40 mm run under the tray: a tray fitted onto a flat floor with the waste run flat is a permanent slow drainer, and the fix is to lift the tray or re-run under the floor.
Baths need the panel off or an access hatch. If there is neither, make one: a bath trap that cannot be reached will be back. Replace shallow-seal or non-removable traps with a 40 mm tubular trap with a cleaning eye while you are there.
Step 6 — what not to do
Do not pour caustic soda, sulphuric acid or proprietary "heavy duty" cleaners into a trap that has already been treated or that is connected to old ABS, rubber-sealed or lead pipework; the heat and chemistry attack the material, and the residue is a hazard to whoever opens the trap next (you). If the customer has used them, wear gloves and eye protection when dismantling, and rinse before handling. Enzyme or bacterial maintenance products are harmless to pipework and are a reasonable recommendation for a kitchen sink once it is clear. Do not use a plunger on a basin with the overflow open; it just pumps air through the overflow. Cover it with a wet cloth first.
When the local fault is not the fault
Two patterns should send you to the drain even if only one appliance was reported: a ground-floor appliance or a shower tray that is slow and that also fills slightly when a WC is flushed or a bath empties (the lowest connection is first to show a downstream blockage), and a slow kitchen sink whose outside gully is standing full of water (the gully or the drain beyond it is blocked, not the sink). In both cases clearing the trap will make no difference. See outside drain overflowing and blocked drain clearance pricing guide.
Frequently Asked Questions
Why does my basin keep blocking a few months after it is cleared?
Because the pipework holds debris. The usual culprit is a corrugated flexible waste connector, which collects hair and soap in every rib and sags into a sump; the second is a branch run flat or with insufficient fall; the third is a pop-up plug mechanism. Clearing the blockage treats the symptom; replacing the flexi with rigid pipe at the right fall and fitting a clicker or flip waste removes the cause.
Can I just use a chemical drain cleaner?
For a hair and soap blockage in a basin or bath, a caustic cleaner may dissolve enough to restore flow for a while, but it leaves the mechanism and the pipe fouling in place, generates heat that can soften ABS and perish seals, and makes the trap hazardous to dismantle afterwards. For fat in a kitchen trap it rarely works at all. Mechanical clearance of the trap is faster, cheaper and permanent, and is what a tradesperson should be doing.
How long can a basin waste pipe be?
Approved Document H1 Table 2 allows a 32 mm basin branch of up to 1.7 m without ventilation, at a fall of 18–90 mm per metre, and the 1.7 m is only achievable at the shallower gradients. If the basin is further from the stack than that, use 40 mm pipe (3.0 m), add an air admittance valve or vent at the head of the run, or fit an anti-siphon trap. A 32 mm run of 2.5 m with three elbows will drain slowly and gurgle for the whole of its life.
The bath drains slowly and the plughole smells. Is that connected?
Usually. A long or flat 40 mm run pulls the seal out of the bath trap by self-siphonage as the bath empties, leaving a shallow or empty trap that lets drain air into the room. Clean the trap, then check the run length and fall; the smell and the slow drain have the same cause. If the smell persists with a full seal, see drain smell in house.
Is slow draining ever a sign of a bigger problem?
Yes, when it is not confined to one appliance. A ground-floor appliance that is slow and that rises when the WC flushes, a gully standing full outside the kitchen, or two appliances slowing together all point to the stack, the drain or a lost vent, and the fix is at the chamber or stack, not under the sink. Rodding a trap in that situation wastes the customer's money.
Regulations & Standards
Building Regulations 2010, Approved Document H, Section H1 (Foul water drainage) — Table 1 minimum trap sizes and seal depths; Table 2 maximum unventilated branch lengths; gradient of 18–90 mm per metre for branch discharge pipes; access for clearing blockages
BS EN 12056-2:2000 — Gravity drainage systems inside buildings: sanitary pipework, layout and calculation (the design standard behind Approved Document H1)
BS EN 12380:2002 — Air admittance valves for drainage systems
BS EN 274-1:2002 — Waste fittings for sanitary appliances: requirements (traps and waste outlets)
BS EN 1329-1 and BS EN 1455-1 — PVC-U and ABS soil and waste discharge pipework systems; BS EN 1451-1 — polypropylene
Water Supply (Water Fittings) Regulations 1999 — backflow and air-gap requirements where appliance hoses connect to waste fittings
Control of Substances Hazardous to Health Regulations 2002 (COSHH) — handling caustic and acidic drain cleaners and their residues
Consumer Rights Act 2015 — work to be carried out with reasonable care and skill
Approved Document H: Drainage and waste disposal — GOV.UK — trap seals, branch lengths and gradients
HSE: COSHH basics — handling hazardous cleaning chemicals
WaterSafe: Plumbing advice for homeowners — approved plumber guidance on waste and water fittings
CIPHE — Chartered Institute of Plumbing and Heating Engineering — technical guidance on sanitary pipework
British Plastics Federation: Plastic pipes group — waste pipe material compatibility
waste pipes — waste pipe sizes, gradients and maximum run lengths in full
gurgling drains diagnosis — when the slow drain gurgles or affects other appliances
blocked drain diagnosis — the downstream diagnosis when the fault is not local
outside drain overflowing — gully and drain blockages that present as a slow kitchen sink
kitchen waste and supply connections — kitchen trap, spigot and appliance hose arrangements
dishwasher not draining — the appliance side of a shared kitchen trap
blocked drain clearance pricing guide — pricing when the job becomes a drain clearance