Summary
Creaking floors are the most common complaint in houses of every age, and the most commonly mis-fixed. The DIY response is talcum powder in the gaps, or a few nails in the noisy board, which silences the symptom for a fortnight. The trade response is to understand that a creak needs three things: movement, friction and a gap for the movement to happen in. Remove any one and the creak stops. Boards lifting off joists (loose fixings), boards rubbing against each other (shrinkage opening tongue-and-groove joints, or a board edge rubbing a neighbour), chipboard rubbing on a joist that has shrunk away, a joist that has dropped on a sleeper wall or hanger, a pipe clipped to a joist that squeaks as the board above moves: each has a different fix, and only the first is cured by a screw.
Stairs are the same problem in a different shape. A traditional cut-string or closed-string stair is held together with glued wedges driving the treads and risers into housings in the strings, and glue blocks in the internal angle between tread and riser. Fifty years of drying and foot traffic loosen the wedges, the glue blocks fall off and the tread flexes against the riser tongue on every step. The fix is from below, re-wedging and re-blocking, which is a two-hour job if the underside is accessible and a half-day with plastering if it is boxed in. The alternative, screwing down through the tread into the riser from above, works only where there is enough timber and the heads can be hidden.
The regulatory position matters because customers ask whether it is a "defect". Approved Document E concerns sound insulation between dwellings and rooms, not creaks, and there is no Building Regulations tolerance for creaking floors in a single dwelling. New-home warranty providers (NHBC Standards Chapter 6.4 and equivalents) accept some floor noise but treat persistent creaking caused by inadequate fixing as a defect in the first two years. For the joist rules referenced throughout see notching and drilling joists rules and joist installation; for stair construction see staircase construction.
Key Facts
- Root cause — a creak needs movement plus friction; cure the movement (fix the board to the joist, fill the gap, stiffen the joist) rather than the friction (lubricant), which is temporary.
- Boards lifting on nails — the most common cause in pre-1960 softwood-boarded floors: cut floor brads lose grip as the joist dries; the board rises 1–3 mm under load and drops back with a creak.
- Screw specification — 4 mm or 4.5 mm × 50–60 mm for 20–22 mm boards on softwood joists; penetration into the joist at least 2.5 times the board thickness or 35 mm, whichever is greater; countersunk heads flush or below surface; two screws per joist crossing, 20–25 mm from board edges.
- Locate the joist — joists at 400 mm centres in most post-1960 houses, 350–450 mm in older ones; find them from the existing nail lines, a stud detector, or by lifting one board; screwing into fresh air is the classic error.
- Services under boards — pipes and cables run in notches at the top of joists near the bearing and through holes near mid-depth; Approved Document A (and BS 8103-3) permits notches only within 0.07–0.25 of the span from the support, maximum depth 0.125 × joist depth, and holes within 0.25–0.4 of the span, maximum diameter 0.25 × joist depth, so a board over the first 400 mm from a wall is the highest-risk zone for pipes.
- Chipboard floors — 18 mm (400 mm centres) or 22 mm (600 mm centres) tongue-and-groove to BS EN 312 P5 (moisture-resistant); creaks come from unglued T&G joints, unglued or unfixed joist bearings, and joists shrinking after installation; screw at 300 mm centres along joists and 150 mm at board ends, and glue T&G joints with PVA or polyurethane when boards are lifted.
- Joist shrinkage — softwood joists installed wet can shrink 3–5% across the grain as the house dries; a 220 mm joist loses up to 8 mm, leaving boards above suspended on the fixings; pack or re-fix.
- Noggins and strutting — herringbone or solid strutting is required at mid-span for joists over 2.5 m (one row) and at third-points over 4.5 m (two rows); missing or loose strutting lets joists twist and boards creak against each other.
- Sleeper walls and bearings — joists bearing on a shrunk timber wall plate or a loose joist hanger move as a unit; the whole area creaks; fix by packing with slate or hardwood, or by fitting a hanger correctly.
- Pipes — a copper pipe clipped tight to a joist and crossing under a board creaks as the board deflects; the fix is a felt or foam sleeve, not more fixings.
- Floating floors — laminate and engineered boards on underlay creak if the subfloor is uneven by more than 3 mm over 2 m (BS 8201 tolerance), if there is no expansion gap and the floor is pinched, or if the underlay has compressed; the cause is the subfloor, not the board.
- Stairs: wedges and glue blocks — a traditional stair has two wedges per tread and two per riser driven into the string housings, and two or three glue blocks (50 × 50 mm triangular or square section, 100 mm long) per tread; re-glue with PVA or polyurethane and re-drive, or replace split wedges with new ones cut from hardwood.
- Stairs: fixing from above — where the underside is inaccessible, 4 mm × 50 mm screws down through the tread into the top of the riser at 200 mm centres, counterbored and plugged or filled, with the riser's tongue glued; two screws from the back of the riser into the back edge of the tread below where there is a gap.
- Stairs: regulations — repairs do not alter the stair's rise, going or headroom and are outside Approved Document K, but a tread replaced must match the existing rise and going; rise 150–220 mm, going 220–300 mm for a private stair; see staircase regs.
- Approved Document E — concerns resistance to the passage of sound between dwellings, not creaks within a dwelling; a creak is not an E failure.
- New-build tolerances — NHBC Standards Chapter 6.4 Timber and concrete upper floors and the Consumer Code treat persistent creaking from inadequate fixing as a defect in the first two years.
- Costs — a competent carpenter silences a bedroom floor in 1–3 hours (£60–£180 labour), a chipboard floor with carpet lifted 2–5 hours, a stair from below 1.5–3 hours, a stair from above with plugging 3–5 hours; see carpenter day rate guide.
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Symptom | Likely cause | Test | Fix |
|---|---|---|---|
| Single board creaks underfoot, rises visibly | Board loose on nails | Press board edge: see it move 1–3 mm | Screw down into joist both sides of the gap |
| Creak along a line across the room | Joist dropped or shrunk; boards suspended on fixings | Several boards move together; straight edge shows dip | Pack bearing, re-fix boards to joist |
| Chipboard creaks at a joint, not over a joist | Unglued T&G rubbing | Creak between joists; joint visible | Glue joint (inject PU adhesive) or screw both sides |
| Creak under carpet, whole area, newer house | Chipboard not glued or screwed to joists; joists shrunk | Bounce test; count fixings on lifted board | Lift carpet, screw at 300 mm centres |
| Creak only when stepping near a wall | Board rubbing skirting or a pipe clipped at the joist end | Remove skirting or lift board at wall | Trim board, sleeve pipe |
| Floor bounces and creaks mid-room | Missing or loose strutting; undersized joists | Deflection over 10 mm under one person | Fit herringbone or solid strutting; sister joists if undersized |
| Laminate or engineered floor creaks everywhere | Uneven subfloor, pinched expansion gap, compressed underlay | Check gap at skirting; check level 3 mm/2 m | Relieve gap; level subfloor; re-lay |
| Stair tread creaks at the front | Glue blocks off; riser tongue loose in tread groove | Press nosing; see riser move | Re-block and glue from below; screw tread to riser |
| Stair tread creaks at the string | Wedges loose or split | Look under stair: wedges proud or missing | Re-glue and re-drive wedges; replace split ones |
| Whole stair creaks and flexes | String fixing to wall or newel loose; carriage missing | Push stair sideways; look for gaps at wall string | Re-fix string to wall; fit a carriage piece under centre |
| Creak returns within weeks | Lubricant or nails used; cause not addressed | — | Diagnose movement and screw-fix |
Detailed Guidance
Diagnosis: find the movement first
Walk the room slowly, heel first, and mark each creak with tape. Then kneel and press beside each mark with the flat of the hand and watch: the board that moves is the culprit, and the direction tells you the cause. A board that rises and falls at one edge is loose on the joist below that edge. Two boards whose edges move relative to each other are rubbing at the joint. A whole strip of boards moving together is a joist problem. If nothing visibly moves but the creak persists, the noise is coming from below the board: a pipe, a cable clip, a joist on a loose hanger, or the board rubbing on the joist itself where the joist top is uneven.
CREAKING FLOOR — DIAGNOSIS
│
├─ Does ONE board visibly rise 1–3 mm when pressed at its edge?
│ └─ YES ──> Loose fixing. Screw into joist each side of the lifting point.
│
├─ Do TWO adjacent boards move relative to each other at the joint?
│ └─ YES ──> Edge rub / open T&G. Screw both to joist; glue joint if chipboard.
│
├─ Do SEVERAL boards in a line move together?
│ └─ YES ──> Joist moving (shrunk, dropped bearing, loose hanger).
│ Lift a board, inspect bearing, pack and re-fix.
│
├─ Does the floor BOUNCE (>10 mm under one person at mid-span)?
│ └─ YES ──> Missing strutting or undersized joists. Strut; sister if needed.
│
├─ Is the creak near a wall, radiator or bathroom?
│ └─ YES ──> Suspect a pipe under the board. Lift and sleeve; do not screw.
│
└─ No visible movement, creak remains?
└─ Lift the board. Look for: pipe/cable clip, uneven joist top, loose noggin.
Screwing down a boarded floor
The standard fix for a loose softwood board. Find the joist line from the existing nail heads. Before driving the first screw, confirm what is under the board: lift a board at the edge of the room, or use a pipe and cable detector, or at the very least drill a 3 mm pilot hole and probe. The highest-risk zone is the 400 mm nearest any wall, where plumbers notch pipes into the joist tops, and anywhere a radiator, bathroom or kitchen is nearby. A 60 mm screw through a 15 mm copper pipe is a flood under a floor you have just fixed.
Use 4 mm or 4.5 mm × 50 mm screws for 20 mm boards (60 mm for 25 mm boards), countersunk and driven flush or 1 mm below the surface, two per joist crossing, 20–25 mm in from the board edges. Where the board has cupped, screw the high edge first and pull it down. Fill the holes if the floor is to be exposed. If the old cut nails are proud, drive them below the surface with a nail punch first.
Where a board has been lifted before and has lost its tongue, the cut edge rubs its neighbour; a screw into the joist each side cures it, or glue a thin fillet of timber into the gap.
Chipboard floors
Most post-1970 upper floors are tongue-and-groove chipboard, often laid dry with nails or too few screws, on joists that then dried and shrank. The creak comes from the board rubbing on the joist, from the T&G joint rubbing, or from the nail shank squeaking in the hole. Lift the carpet (a carpet fitter's job if it is to go back without stretch marks), find the joists from the existing fixings, and screw at 300 mm centres along every joist and 150 mm at board ends with 4.5 mm × 50 mm (18 mm board) or 60 mm (22 mm board) screws. For unglued joints between joists, inject polyurethane adhesive into the joint from above through 3 mm holes at 200 mm centres, or screw a 50 × 50 mm batten to the joist side under the joint, or screw both boards down to a noggin fixed between joists. BS EN 312 P5 board that has got wet and swollen will never stop creaking and must be replaced.
Under a laminate or engineered floor laid over chipboard, the creak is usually the chipboard, not the floating floor. Lift the floating floor along one wall, screw down the chipboard, re-lay.
Joists, bearings and strutting
A line of creaking boards across a room is a joist moving. Lift one board over the line and look at the joist. Common findings:
- Shrunk joist: a visible gap of 2–8 mm between the joist top and the board. Pack the gap with hardwood or plywood packers glued to the joist at each board crossing, then screw the boards through the packers into the joist. Do not simply screw the board down to the shrunk joist; that pulls the floor out of level.
- Dropped bearing: the joist end sits on a timber wall plate on a sleeper wall (ground floors) or in a hanger (upper floors). A rotten or crushed plate, or a hanger fixed loose, lets the joist end move. Pack with slate or steel shims, replace the plate, or fix the hanger properly with the correct nails in every hole.
- Missing strutting: joists over 2.5 m span should have a row of herringbone or solid strutting at mid-span; over 4.5 m, two rows. Fit solid strutting from 50 mm × (joist depth − 25 mm) timber, tight between joists and skew-nailed or screwed, or proprietary galvanised herringbone struts. It stiffens the floor and stops joists rolling.
- Undersized or notched joists: deflection over 10–12 mm under one person suggests joists below the span tables or weakened by over-notching. Sister a new joist alongside, bolted at 600 mm centres with M12 bolts and toothed-plate connectors, or ask a structural engineer. See timber spans and floor joist replacement pricing guide.
Pipes, cables and fixings that squeak
A copper pipe clipped tight to the side or top of a joist, or passing through a tight notch, squeaks as the board deflects and the pipe rubs. Lift the board, loosen the clip or replace it with a plastic snap clip, and wrap the pipe in felt or foam pipe insulation where it passes through notches. Never screw a board down over a creaking pipe to "hold it still": the board still moves and the screw may enter the pipe.
Stairs: fixing from below
With the underside accessible (a cupboard under the stairs with the soffit open, or a plasterboard soffit you can remove and replace), the repair is straightforward. Clean the dust off. For each creaking tread, check the wedges: a loose wedge pulls out by hand, a split one has a visible crack. Remove, apply PVA or polyurethane adhesive to the housing and the wedge, and drive it home with a hammer until the tread or riser is tight in the housing. Replace missing wedges with new ones cut from hardwood (oak or beech) to match the taper. Then fit glue blocks: 50 × 50 mm softwood, 100–150 mm long, glued and rubbed into the internal angle between the tread underside and the riser face, two or three per tread, pinned or screwed while the glue sets. Finally, screw up through the riser into the underside of the tread above at 200 mm centres with 4 mm × 40 mm screws where the riser tongue is loose in the tread groove. Allow 1.5–3 hours for a 13-tread flight.
If the stair has a carriage (a central bearer under the treads with brackets), check it is fixed at top and bottom and that the brackets are tight.
Stairs: fixing from above
Where the underside is plastered in and the customer will not accept opening it, work from the top. Lift the carpet. For a creak at the nosing, drive 4 mm × 50 mm screws down through the tread into the top edge of the riser at 200 mm centres, in a line 15–20 mm back from the riser face (locate the riser by its thickness, usually 15–20 mm), counterbored 8 mm and plugged with matching timber or filled under carpet. Glue the joint first by working PVA into any gap. For a creak at the back of the tread, screw at an angle through the tread into the riser above where there is a gap, or fit a small glued fillet in the angle. For the string joint, screw down through the tread into the string where the housing has opened. It is less tidy than working from below and less durable, because the wedges remain loose; tell the customer.
Frequently Asked Questions
Is a creaking floor a Building Regulations failure?
No. The Building Regulations do not address creaking within a dwelling. Approved Document E concerns airborne and impact sound insulation between separate dwellings and between rooms used for residential purposes, not floor noise within a house. Approved Document A covers structural adequacy, and a floor that deflects excessively or has over-notched joists may be an A issue, but the creak itself is not. On a new home, persistent creaking caused by inadequate fixing is a workmanship defect under the warranty provider's standards during the defects period.
Will talc, graphite or lubricant fix it?
Briefly. Lubricants reduce the friction between the rubbing surfaces, which stops the noise until the lubricant works out, typically a few weeks. They do nothing about the movement that causes the rub. The only permanent cure is to stop the movement: fix the board to the joist, glue the joint, pack the joist or re-wedge the stair.
Can I screw down floorboards without lifting them?
Yes, and that is the normal fix, with one condition: you must know what is under the board. Pipes run in notches at the top of joists, mostly within 400 mm of walls and near radiators and bathrooms, and a 50 mm screw will go straight through 15 mm copper. Use a detector, check the pipe routes from radiators and sanitaryware, drill a pilot and probe, or lift one board to see. Never guess near a wall.
Why does a new-build floor creak after a year?
Because the joists were installed with a moisture content of 20% or more and have dried to 10–12% in a heated house, shrinking several millimetres and leaving the chipboard suspended on its fixings. Nails, where used, lose grip; the board rubs on the fixing and on the joist. Screwing at close centres cures most of it; packing is needed where the gap is large. Report it to the warranty provider within the two-year defects period.
How much does it cost to stop a floor creaking?
A carpenter charges roughly £35–£55 per hour regionally. A boarded bedroom floor with easy access takes 1–3 hours; a carpeted chipboard floor 2–5 hours plus a carpet fitter to lift and refit (£60–£120); a stair from below 1.5–3 hours; a stair from above 3–5 hours. Materials are a box of screws, a tube of polyurethane adhesive and some packers, under £30. A bouncing floor that needs strutting or sistering is a different job at £300–£1,200.
Regulations & Standards
Building Regulations 2010, Approved Document A: Structure (2004 edition incorporating 2010 and 2013 amendments) — floor joist span tables (via TRADA and BS 8103-3) and the notching and drilling limits for joists.
BS 8103-3:2009+A1:2013 — Structural design of low-rise buildings: code of practice for timber floors and roofs for housing (joist spans, strutting, notches and holes).
BS EN 312:2010 — Particleboards: specifications (P5 moisture-resistant flooring grade).
BS 8201:2011 — Code of practice for installation of flooring of wood and wood-based panels (subfloor tolerances, expansion gaps, fixing).
BS 1297:1987 — Specification for tongued and grooved softwood flooring.
BS 5395-1:2010 — Stairs: code of practice for the design of stairs with straight flights and winders.
Building Regulations 2010, Approved Document K: Protection from falling, collision and impact — stair rise and going where a tread is replaced.
Building Regulations 2010, Approved Document E: Resistance to the passage of sound — relevant only to confirm that floor creak within a dwelling is outside its scope.
NHBC Standards 2024, Chapter 6.4 Timber and concrete upper floors — fixing requirements and tolerances for new-build floors.
Approved Document A: Structure — joist notching and drilling limits and structural requirements
TRADA – Span tables for solid timber members in floors, ceilings and roofs — joist spans and strutting requirements
NHBC Standards – Chapter 6.4 Timber and concrete upper floors — new-build floor fixing and tolerances
BSI – BS 8201:2011 Code of practice for installation of flooring of wood and wood-based panels — subfloor tolerances and fixing
Wood Panel Industries Federation – Chipboard flooring installation guidance — P5 flooring installation, gluing and fixing
Approved Document E: Resistance to the passage of sound — scope of the sound regulations
notching and drilling joists rules — where pipes and cables are allowed to be, and therefore where not to screw
joist installation — bearings, hangers and strutting done right
staircase construction — wedges, glue blocks and housings explained
timber spans — checking whether a bouncy floor is undersized
subfloor preparation — tolerances for floating floors
floor joist replacement pricing guide — when the fix is structural
carpenter day rate guide — pricing the repair