Summary
Solar panel cleaning is a service that sells on a number the customer can see: generation. A dirty array in a UK climate loses 3–8% of output on average, more where there is bird soiling under a roost, tree pollen, lichen growth on older panels, or agricultural dust, and the inverter app shows the drop. A clean restores it. The trade problem is that cleaning looks easy — it is window cleaning on a roof — and the price the market expects (£5 a panel) only works from the ground with a water-fed pole on a modern two-storey house with the array on the front pitch. The same array on a rear pitch over a conservatory, or a bungalow with a low eaves and a steep pitch the pole cannot reach along, or a 30-panel array on a three-storey townhouse, is a tower or a roof-access job and costs three times as much to do safely.
The second trade problem is safety. The Work at Height Regulations 2005 apply to every solar cleaning job, and a ladder is not a working platform for a 90-minute clean. Cleaners who go onto the roof need edge protection or fall arrest and a roof ladder; cleaners who work from the ground need a pole that reaches, which caps the practical reach at about 18–20 m with a carbon-fibre pole and realistically 12–15 m for control. Pricing has to start from the access method, and the quote has to say which one. This guide gives the per-panel and per-visit figures, the equipment and consumable costs, the labour times by access method, the add-ons that make the visit worth more, and the commercial and ground-mount rates.
For what to offer alongside cleaning see solar pv cleaning and maintenance; for the system itself see solar pv; for access see working at height.
Key Facts
- Per panel, domestic, from the ground — £4–£10 per panel; typical 10–14 panel array £100–£180
- Per panel, roof access or tower — £8–£18 per panel; the same array £150–£300, because the tower hire or the fall-protection set-up is two hours before a panel is touched
- Minimum call-out — £80–£150; a 6-panel array still needs the van, the water and the drive
- Commercial roof-mount — £1.50–£4 per panel on 100+ panels, with access priced separately (MEWP hire £200–£400 a day); or £15–£35 per kWp
- Ground-mount and solar farms — £0.80–£2 per panel; tractor-mounted brush systems at scale, not a water-fed pole
- Frequency — annual in most of the UK; twice a year under trees, near the coast, near bird roosts or on farms; the customer can see when the output drops
- Output loss from soiling — 3–8% typical UK annual average; 10–25% under bird roosts or heavy lichen; a 4 kWp array producing 3,400 kWh a year at a 5% loss is 170 kWh, worth £25–£45 at 2026 import prices plus lost export; the economics work for the customer at £120 every year or two
- Water — purified water only (DI resin or reverse osmosis to under 10 ppm TDS); tap water at 200–400 ppm leaves mineral spots that bake on. A 100-litre tank covers 15–25 panels; DI resin costs £0.50–£2 per 100 litres depending on local hardness
- No detergent, no pressure washer — most manufacturers' warranties specify water and a soft brush; detergents leave a film, pressure washers can breach the frame seal and crack cells; abrasives scratch the anti-reflective coating
- Pole — carbon-fibre water-fed pole to 18–20 m, £300–£900; soft solar brush head £40–£80; hoses, pump and tank £300–£800; a full ground-based set-up is £1,500–£3,500
- Time per panel — 5–10 minutes from the ground; 3–5 minutes per panel once set up on the roof, plus 1–2 hours of access set-up and strike
- Ladder rule — Work at Height Regulations 2005, Schedule 6: ladders only where the work is low-risk and short-duration; a solar clean is neither. Use a tower, a MEWP or roof access with edge protection or a fall-arrest system
- Roof access — crawl boards or a roof ladder hooked over the ridge, a harness to an anchor, never standing on the panels (micro-cracks) and never walking on the glass; see solar panel roofing
- Electrical — panels are live in daylight; a cleaner does not touch connectors or the inverter. Visual inspection of cabling, the DC isolator and the inverter display is a reportable add-on, not electrical work
- Bird-proofing — mesh clipped around the array perimeter, £15–£30 per linear metre supplied and fitted; the most common upsell on an array with a pigeon problem; see solar pv cleaning and maintenance
- Inspection add-on — a 20-minute visual check and an inverter reading before and after, written up as a one-page report, adds £40–£80 to the visit and the generation evidence sells the next clean
- Insurance — public liability £1–£2 million; most window-cleaning policies cover solar cleaning from the ground but ask about roof access; £300–£700 a year
- VAT — compulsory registration above £90,000; most sole-trader cleaners are below it
- Materials markup — DI resin, bird mesh, clips and any replacement cable clips at trade cost plus 20–30%
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Regional (outside London/SE) | South East | London | Notes |
|---|---|---|---|---|
| Domestic, 6–10 panels, from the ground | £80–£130 | £90–£150 | £110–£180 | Minimum call-out applies |
| Domestic, 10–14 panels, from the ground | £100–£180 | £120–£200 | £150–£240 | Typical 4 kWp array |
| Domestic, 14–20 panels, from the ground | £140–£220 | £160–£250 | £200–£300 | |
| Domestic, any size, tower required | +£60–£120 | +£70–£140 | +£90–£160 | Tower hire and 1 hr set-up/strike |
| Domestic, roof access with fall protection | £150–£300 | £180–£350 | £220–£420 | Two operatives recommended |
| In-roof / integrated panels (flush, harder to edge) | +10–20% | +10–20% | +10–20% | Water and debris sit at the frame line |
| Bird-proofing mesh, per linear metre | £15–£30 | £18–£32 | £20–£38 | Supplied and fitted during the clean |
| Visual inspection and inverter reading, written report | £40–£80 | £45–£90 | £55–£100 | Add-on |
| Commercial roof-mount, per panel (100+) | £1.50–£4 | £1.80–£4.50 | £2–£5 | Access priced separately |
| Commercial per kWp | £15–£35 | £18–£38 | £20–£45 | |
| Ground-mount, per panel (500+) | £0.80–£2 | £0.80–£2 | £0.80–£2 | Mechanised |
| Annual service contract (clean + inspection), domestic | £150–£260 | £170–£290 | £200–£340 | Billed yearly, booked in advance |
Detailed Guidance
Price from the access method, not the panel count
Before quoting, establish how the array will be reached:
| Situation | Access | Time, 12 panels | Price basis |
|---|---|---|---|
| Two-storey house, array on a pitch facing an accessible garden or drive, eaves 5–6 m | Water-fed pole from the ground | 60–90 min | Per panel, £4–£10 |
| Array on a pitch over a conservatory, extension or narrow side return | Pole from a tower or from the flat roof with edge protection | 2–2.5 hrs | Per panel + tower uplift |
| Bungalow, low eaves, steep pitch, array runs up to the ridge | Pole from the ground usually reaches; check angle | 60–90 min | Per panel |
| Three-storey townhouse, eaves 8–9 m | Long pole (16–18 m) from the ground if reach allows, otherwise tower or MEWP | 1.5–3 hrs | Per panel + uplift |
| Array on the far side of a pitch, no ground access | Roof access with roof ladder, harness and anchor; two operatives | 3–4 hrs | Roof-access rate |
| Commercial flat roof with parapet | Walk the roof with edge protection; pole or hand brush | per panel | Commercial rate + access |
Say in the quote which method is priced and what happens if the access on the day is different ("priced from the ground; if a tower is required on arrival, +£90"). A cleaner who turns up with a 12 m pole for a job that needs 16 m goes home unpaid.
Labour time and the hourly rate behind the per-panel price
A sole-trader solar cleaner's cost base is lower than a plumber's — no stock, cheaper tools — but the van, the water system and the insurance still have to be recovered, and the work is seasonal (March to October, with a spring rush when the output drop becomes visible). A reasonable day rate target is £200–£280, which on 6 billable hours is £35–£45 an hour. At 7 minutes a panel from the ground plus 30 minutes set-up and strike, a 12-panel clean is about 1.75 hours: £60–£80 of labour, plus water (£2–£4), plus travel. That is the floor under a £100–£140 price for the job and the reason the per-panel rate has to come with a minimum call-out. Two 12-panel jobs in a morning and two in the afternoon is £450–£600 a day in season, which is the whole business model, and it depends on routing the jobs by postcode and booking a street at a time.
Water, equipment and consumables
- Purified water — the only consumable that matters. DI resin vessels (£150–£400) are simple and the resin lasts 1,000–4,000 litres depending on hardness; in hard-water areas (most of the South East and East Anglia at 250–400 ppm) an RO system (£500–£1,500) with a DI polish is cheaper per litre over a season. Target under 10 ppm TDS at the brush; a £15 TDS meter is the quality control
- Pole and brush — a carbon-fibre pole is lighter and stiffer than fibreglass and worth the money above 10 m; a dedicated solar brush head with soft bristles and a wide jet pattern; never a window brush with hard bristles
- Pump and tank — 100–300 litre van tank, 12 V pump with a flow controller; 100 litres cleans 15–25 panels
- Access kit — a 3 m or 4 m alloy tower (£60–£120 a day to hire, £800–£1,500 to own) for the conservatory and side-return jobs; for roof access, a roof ladder, a harness, a certificated anchor (temporary ridge anchor or a rafter-fixed eyebolt to BS EN 795) and the training to use them
- Camera — photographs before and after, from the ground with a zoom, go on the invoice and sell the next visit
Water is charged inside the per-panel price, not as a line. Bird mesh, clips and replacements are materials at trade cost plus 20–30%.
Add-ons that turn a clean into a service visit
The margin in solar cleaning is in the visit, not the panels:
- Visual inspection and generation check — read the inverter before and after, photograph the array, note any cracked glass, discoloured cells (hot spots), loose cable clips, exposed DC cable, damaged or sun-degraded bird mesh, debris under the panels, and the condition of the DC isolator. Write it up on one page. £40–£80, and it is what justifies an annual contract
- Bird-proofing — pigeons under panels are the commonest complaint; a mesh skirt clipped to the frame (no drilling, no roof penetration) at £15–£30 per linear metre, plus removal of nests and droppings (£50–£150, with PPE — pigeon droppings carry psittacosis and histoplasmosis risk)
- Gutter clearance — you are there with a pole; £40–£80 for the gutters on the same elevation
- Moss and lichen — lichen on panel edges needs a second pass with more dwell time; price it as +25–50% when you see it on the survey photos
- Annual contract — clean plus inspection every 12 months at £150–£260, booked in advance, invoiced on the day; a 60-contract book is a season's base income
Keep electrical work out of the visit unless the operative is qualified for it: a loose MC4 connector or a tripped DC isolator is a report item for a solar electrician, not something a cleaner opens. See solar pv not generating for what the customer should be told to do next.
Commercial and ground-mount arrays
Commercial pricing is per panel on volume or per kWp, with access as a separate line. A 400-panel warehouse roof at £2.50 a panel is £1,000 for the clean, plus a MEWP at £250–£400 a day if the roof cannot be walked, plus the edge-protection or harness set-up, plus a RAMS pack the facilities manager will want (two hours of desk time). Two operatives at 150–200 panels a day each sets the labour. Ground-mounted arrays and solar farms are a different business — tractor-mounted rotating brush systems, water bowsers and a per-MW price — and a domestic cleaner should quote them only as a subcontractor to a specialist.
Warranty, manufacturer guidance and what to put in writing
Most panel manufacturers' installation and maintenance guidance specifies cleaning with water and a soft brush or sponge, no abrasives, no high-pressure water, no solvents, and no cleaning when the glass is hot (thermal shock risk — clean early morning or on overcast days in summer). State on the quote that cleaning is with purified water and a soft brush only, that no detergent or pressure washing is used, and that the operative will not walk on the panels. That protects the customer's warranty and protects you when a pre-existing micro-crack shows up a month later: the before-and-after photographs are the evidence. See solar pv cleaning and maintenance for the customer-facing version.
Worked example: 14-panel array, two-storey semi, front pitch, from the ground
Travel and set-up (tank, pole, hoses, TDS check) 30 min
Clean 14 panels at 7 min each 98 min
Rinse, inverter reading, 6 photographs, strike 20 min
--------
On site ~2.5 hrs
Labour at £40/hr £100
Water: 110 litres DI at £1.20 per 100 litres £1.50
Van and travel (in the day rate) —
Price quoted: 14 panels × £8 = £112, rounded to £120
Add-on sold: inspection and report £50
Add-on sold: bird mesh, 9 m perimeter at £22/m £198
Invoice £368
The clean alone is £120 for 2.5 hours — adequate. The visit is £368 for about 3.5 hours, with the mesh at a 25% materials margin — that is the business.
Frequently Asked Questions
How much should I charge to clean solar panels?
£4–£10 per panel from the ground with a £80–£150 minimum, so a typical 10–14 panel domestic array is £100–£180 in 2026. If a tower is needed add £60–£120; if roof access with fall protection is needed, £150–£300 for the same array. Commercial arrays £1.50–£4 per panel on volume, access extra.
Can I use a pressure washer or washing-up liquid?
No. Pressure washers can force water past the frame seal and crack cells; detergents leave a film that attracts dirt and most manufacturers' warranties exclude them. Purified water (under 10 ppm TDS) with a soft brush is the industry standard and the one that keeps the customer's warranty intact.
Is it safe to clean solar panels from a ladder?
Not as a working platform. The Work at Height Regulations 2005 allow ladders only for low-risk, short-duration work, and a 90-minute clean is neither. Work from the ground with a water-fed pole, from a tower, or from the roof with a roof ladder and a harness anchored to a rated point. Never stand or walk on the panels.
How often should solar panels be cleaned in the UK?
Once a year for most domestic arrays; twice a year under trees, near the coast, under a bird roost or on a farm. Rain removes loose dust but not pollen film, lichen, bird droppings or the dirt line along the bottom frame edge, and the inverter app shows the difference after a clean.
Should I offer an annual contract?
Yes. A clean plus a 20-minute visual inspection and a one-page report, booked for the same month each year at £150–£260, gives the customer a reason to keep you and gives you a base income you can route by postcode. It is also the natural point to sell bird-proofing and to spot a failing inverter or a cracked panel before the customer notices a generation drop.
Regulations & Standards
Work at Height Regulations 2005 (SI 2005/735) — planning, equipment hierarchy, Schedule 6 (ladders only for low-risk, short-duration work), collective protection before personal
Health and Safety at Work etc. Act 1974 — general duties of the self-employed whose work affects others
Provision and Use of Work Equipment Regulations 1998 (SI 1998/2306) and Lifting Operations and Lifting Equipment Regulations 1998 (SI 1998/2307) — towers and MEWPs
BS EN 795:2012 — personal fall protection anchor devices (ridge anchors, eyebolts)
BS EN 1004-1:2020 — mobile access and working towers made of prefabricated elements
Electricity at Work Regulations 1989 (SI 1989/635) — panels are live in daylight; no interference with DC connectors or isolators by unqualified operatives
Control of Substances Hazardous to Health Regulations 2002 (SI 2002/2677) — bird droppings (biological agents) when clearing roosts
MCS 012 / MIS 3002 — roof-mounted PV installation standards; relevant to what a cleaner should not disturb (fixings, flashings)
Consumer Rights Act 2015 — reasonable care and skill; reasonable price where none agreed
IET Code of Practice for Grid-connected Solar Photovoltaic Systems — maintenance and inspection guidance
HSE — Work at height: a brief guide (INDG401) — the Regulations and the ladder rule
HSE — Safe use of ladders and stepladders (INDG455) — when a ladder is acceptable
Energy Saving Trust — Solar panels — maintenance and cleaning guidance for homeowners
MCS — Standards and guidance for PV — installation standards that cleaning must not disturb
IET — Code of Practice for Grid-connected Solar Photovoltaic Systems — inspection and maintenance practice
Federation of Window Cleaners — Safety guidance — water-fed pole working practice
solar pv cleaning and maintenance — what to offer customers and why; the technical side of this guide
solar pv — the system, the components and what a cleaner should not touch
working at height — towers, roof ladders, harnesses and the ladder rule
solar panel roofing — roof fixings and walking routes on a PV roof
solar pv not generating — what to tell the customer when the inverter shows a fault
solar pv installation pricing guide — the installation side, for context on array sizes
emergency callout pricing guide — minimum charge logic for small jobs