Summary
Laminate is the flooring job most often priced wrong by general tradespeople, because the headline material is cheap and the laying is quick. A competent fitter lays 25–40 m² of straightforward laminate in a day, and the homeowner knows the planks cost £12 a square metre at the shed. What they do not see is the two hours of subfloor preparation, the five doors that need trimming, the radiator pipe collars, the threshold bars and the fact that a 20 m² room needs 22 m² of boards. Fitters who quote "£10 a metre, all in" then discover the room is 7 mm out of level across the width and the old carpet gripper has to come up are working for nothing.
This guide prices the job the way a specialist flooring contractor prices it: a labour rate per square metre for the laying, a separate line for every preparation and finishing task, a materials schedule with realistic wastage, and a margin that reflects the warranty exposure. It covers click-lock laminate on timber and concrete subfloors in domestic settings. For the installation method itself, see laminate flooring installation guide; for the comparison with vinyl plank, see lvt vs laminate comparison.
The regulatory side is light compared with most trades, but not absent. Laminate over underfloor heating has a combined tog limit; a ground-floor concrete slab needs a moisture test before anything goes down; and a floating floor needs its expansion gap, which means door linings are undercut and skirting or scotia is reinstated. Each of those is a line in the quote.
Key Facts
- Labour rate — £8–£12/m² for a plain straight lay in an open room; £12–£15/m² where there are alcoves, bays, hearths and more than three doorways; £15–£25/m² for herringbone or diagonal patterns
- Fitter day rate — £180–£280 (owner-operator, England outside London); £250–£350 in London and the South East. A good fitter lays 25–40 m² of straight laminate per day including underlay
- Material — laminate — budget AC3 8 mm £8–£14/m²; mid-range AC4 8–10 mm £14–£25/m²; premium AC5 12 mm, water-resistant or herringbone £25–£45/m²
- Material — underlay — 2–3 mm foam £1–£2/m²; fibreboard or rubber acoustic 5 mm £3–£6/m²; combined DPM underlay for concrete £2–£4/m²
- Wastage — 7–10% for a straight lay, 12–15% for diagonal or herringbone. Always round up to whole packs and quote the pack count, not the room area
- Expansion gap — 8–10 mm at every wall, door frame, pipe and fixed unit; rooms over about 8–10 m in either direction may need an intermediate expansion joint and a cover profile (manufacturer's instruction governs)
- Acclimatisation — packs flat in the room for 48 hours minimum before laying; price the delivery visit if you supply the boards
- Subfloor flatness — ±3 mm over 2 m; levelling compound at £12–£20/m² supply and lay where it fails (see floor levelling compounds)
- Moisture — concrete or screed must be tested with a hygrometer to BS 8203 methodology (typically below 75% RH) before laying; a surface meter is not sufficient on a slab of unknown history
- Underfloor heating — combined tog of laminate plus underlay should not exceed 1.5 tog on most wet UFH systems; check the floor manufacturer's maximum surface temperature, usually 27 °C
- Door trimming — £10–£20 per door for undercutting linings; £25–£45 per door for planing and rehanging a door that fouls the new floor level
- Finishing trims — scotia £2–£4/m supplied, £3–£5/m fitted; removing and refitting existing skirting £6–£10/m; threshold and T-bar profiles £10–£25 each supplied
- Old floor removal — carpet, gripper and underlay £3–£5/m²; glued vinyl or old laminate £5–£10/m²; disposal £40–£120 depending on volume (see skip hire pricing guide)
- Standard — BS 8201:2011 Code of practice for installation of flooring of wood and wood-based panels; laminate itself is specified to BS EN 13329
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job component | Unit | Typical price (ex VAT, 2026) |
|---|---|---|
| Lay laminate and underlay, straight, open room | per m² | £8–£12 labour |
| Lay laminate, complex room (alcoves, bay, hearth, 3+ doors) | per m² | £12–£15 labour |
| Lay herringbone or diagonal laminate | per m² | £15–£25 labour |
| Supply AC4 laminate, mid-range | per m² | £14–£25 |
| Supply underlay (foam / acoustic / DPM) | per m² | £1–£6 |
| Remove carpet, gripper and underlay | per m² | £3–£5 |
| Self-levelling compound, supply and lay | per m² | £12–£20 |
| Ply overlay 6 mm on uneven timber floor, supply and fix | per m² | £15–£25 |
| Undercut door lining | per door | £10–£20 |
| Trim and rehang door | per door | £25–£45 |
| Scotia, supply and fit | per linear m | £5–£9 |
| Remove and refit skirting | per linear m | £6–£10 |
| Threshold / T-bar / ramp profile, supplied and fitted | each | £20–£40 |
| Radiator pipe collars | per pair | £5–£10 |
| Waste disposal (one room) | each | £40–£120 |
Detailed Guidance
Pricing structure: never quote a single per-metre figure
The most common pricing error is a single all-in rate. It fails because the area to be laid is the one thing on the job that is predictable; everything else varies by property. Structure the quote in four sections:
- Preparation — removal of existing floor covering, disposal, subfloor repairs (loose boards screwed down, ply overlay, levelling compound), moisture testing.
- Laying — labour per m² for the laminate and underlay, with the rate stated for the pattern quoted.
- Finishing — door undercuts, door trimming, scotia or skirting, thresholds, pipe collars.
- Materials — boards by pack count, underlay by roll, trims by length, with wastage shown.
Price each section as a separate line so the customer can see that a floor is a sequence of tasks. When the customer asks why a 20 m² room costs £800 when the boards were £240, the answer is already on the quote.
Labour rates and productivity
A fitter working alone lays a straightforward room at roughly 4–6 m² per hour once the underlay is down, so 25–40 m² per day including set-up, underlay and the first and last row cuts. Productivity drops hard with complexity. A bay window costs the same as three straight metres. A fireplace hearth with a curved front costs an hour. Every doorway is a lining to undercut, a threshold to fit and often a cut around an architrave.
Herringbone laminate is a different job. Each plank is short, the pattern has to be set out from a centreline, every perimeter piece is a 45-degree cut, and wastage climbs to 12–15%. A good fitter manages 12–18 m² a day. Price it at roughly double the plain rate, and make sure the customer understands why before they see the figure.
Day-rate benchmarks for an experienced owner-operator flooring fitter in 2026 are £180–£280 outside London and the South East and £250–£350 inside. See handyman hourly rate pricing guide for how those rates are built up from overheads, and day rate to hourly rate calculator for turning a day rate into a chargeable hourly figure.
Materials: boards, underlay, trims
Boards. Price by the pack, not the square metre. A pack covers a stated area, typically 1.6–2.5 m² depending on plank size. Calculate the room area, add wastage (7–10% straight, 12–15% diagonal or herringbone), divide by the pack coverage and round up. Quote the number of packs and tell the customer one spare pack should stay in the house for repairs. If the customer supplies the boards, state in writing that you are not responsible for board quality, quantity shortfall or warranty, and charge for any second visit caused by running out.
Underlay. Match the underlay to the subfloor and the use. On concrete or screed, a combined underlay with an integral damp-proof membrane, or a separate 1,000-gauge polythene DPM lapped and taped under the underlay, is not optional. On timber, a plain foam or fibreboard underlay is adequate, with acoustic underlay where the room is above a habitable room or the customer wants to reduce footfall noise (see acoustic underlay selection). Over underfloor heating, use a low-tog underlay designed for the purpose and check the combined figure against the heating manufacturer's limit.
Trims. Scotia is quicker and cheaper than removing and refitting skirting, but many customers do not like the look. Offer both and price both. Thresholds are needed at every doorway where the laminate meets another floor; a laminate-to-carpet junction needs a ramp or end profile, laminate-to-laminate at a doorway needs a T-bar with an expansion gap beneath it. Allow one profile per door at £20–£40 supplied and fitted.
Subfloor preparation: where the margin is won or lost
Walk the subfloor with a 2 m straight edge before you quote. Laminate tolerates ±3 mm over 2 m; anything worse telegraphs through as a bouncy or clicking joint and eventually breaks the click profile.
- Timber floorboards that are sound but uneven: screw down loose boards (allow 1–2 hours per room) and overlay with 6 mm plywood screwed at 150 mm centres where the unevenness is widespread. Ply overlay runs £15–£25/m² supplied and fixed.
- Chipboard in good condition usually needs only loose sheets screwed down and any swollen edges planed.
- Concrete or screed: check flatness and moisture. A hygrometer test to the BS 8203 method needs 72 hours, so it is either a preliminary visit or a condition of the quote. Levelling compound at £12–£20/m² solves flatness; it does not solve moisture, which needs a liquid DPM or a membrane underlay.
- Existing tiles: laminate can float over sound ceramic tiles with a suitable underlay, but any broken, loose or lipped tiles must be addressed and the height build-up at doors becomes significant.
Put the subfloor work on the quote as a priced provisional item if you cannot confirm it at survey ("Levelling compound to kitchen area if required: £16/m², estimated 6 m² = £96"). It is far easier to remove a provisional sum than to add a cost on the day. See subfloor preparation guide for the full method.
Worked example: 20 m² lounge, straight lay, concrete subfloor
| Item | Quantity | Rate | Line total |
|---|---|---|---|
| Remove carpet, gripper, underlay and dispose | 20 m² | £4.00 | £80 |
| Moisture test (hygrometer, preliminary visit) | 1 | £45 | £45 |
| Levelling compound to hollow area (provisional) | 4 m² | £16.00 | £64 |
| Combined DPM underlay, supplied | 22 m² | £3.00 | £66 |
| AC4 10 mm laminate, 2.2 m² per pack, 10% wastage = 10 packs | 10 | £38.00 | £380 |
| Lay laminate and underlay | 20 m² | £10.00 | £200 |
| Undercut door linings | 2 | £15 | £30 |
| Scotia, supply and fit | 16 m | £7.00 | £112 |
| Threshold profiles | 2 | £28 | £56 |
| Radiator pipe collars | 1 pair | £8 | £8 |
| Subtotal | £1,041 |
Labour content in that quote is about £475 (removal, levelling labour, laying, doors, scotia fitting) for a long day's work plus the preliminary visit, which is the right side of the fitter day rate. Materials are around £565 at trade cost, and should carry a markup of 15–25% on top of trade price if not already built into the rates above. Confirm in the quote that the laminate rate includes a single straight-lay pattern, that an intermediate expansion joint is excluded, and that any additional subfloor work found after lifting the carpet will be agreed before proceeding.
What to put in the quote so the warranty is yours, not your problem
Laminate manufacturers void the warranty for predictable reasons: no expansion gap, laid over a damp slab, no acclimatisation, wrong underlay over UFH. Protect yourself by writing the conditions into the quote:
- Boards acclimatised in the room for 48 hours before fitting (if customer-supplied, customer's responsibility)
- Subfloor moisture tested and recorded; if above the manufacturer's limit, work paused and DPM options quoted
- 8–10 mm expansion gap maintained throughout; skirting or scotia to cover
- Underfloor heating commissioned and run at normal temperature for at least 7 days before laying, then off or at minimum for 48 hours around installation, per manufacturer's instructions
- Price assumes boards laid parallel to the longest wall unless agreed otherwise
- Furniture moved by the customer unless priced
That list is also your defence against the common complaint, three months after laying, that "the floor has gone up in the middle" — almost always a missing expansion gap or a nailed-through scotia.
Frequently Asked Questions
What is a fair all-in supply-and-fit price per square metre?
For a plain room on a sound subfloor, £25–£45/m² supply-and-fit buys a mid-range AC4 laminate, decent underlay, laying and scotia, with doors and thresholds extra. Below about £22/m² someone is using a budget AC3 board or skipping the underlay quality, and above £50/m² you are either in herringbone territory or carrying significant subfloor preparation. Give the customer the breakdown rather than defending a single number.
Should I charge separately for door trimming?
Yes, always. A typical new laminate and underlay adds 10–13 mm to the floor level. Every door lining is undercut so the floor runs beneath it (10–20 minutes each), and any door that then catches needs taking off, planing and rehanging (30–45 minutes). On a hallway with six doors that is half a day, and it is the item most often left off a quote.
Can laminate go over underfloor heating, and does it change the price?
Yes, over wet UFH and most electric systems, provided the combined tog of laminate and underlay stays within the system limit (commonly 1.5 tog) and the floor surface does not exceed about 27 °C. Use a low-tog UFH underlay (£2–£4/m²) and follow the heating-up and cooling-down regime in the laminate manufacturer's instructions. The price impact is the underlay cost and the time for the preliminary heating cycle, which is the customer's job but needs stating in writing. See underfloor heating screed for the screed side.
How much extra is herringbone laminate?
Roughly double the labour: £15–£25/m² against £8–£12/m² for a straight lay. Herringbone planks are short, the setting-out takes an hour before the first plank goes down, and every perimeter cut is a mitre. Wastage rises to 12–15%, so the material cost climbs as well. Quote it as a separate job type with its own rate.
Who is responsible if customer-supplied boards run out?
The customer, provided your quote says so. State that the customer is responsible for quantity, quality and acclimatisation of their own boards, and that a return visit to complete the floor after a shortfall is charged at your call-out rate (£80–£150). Offer to calculate the quantity for them so the problem does not arise.
Regulations & Standards
BS 8201:2011 — Code of practice for installation of flooring of wood and wood-based panels; the governing standard for laying laminate, including subfloor condition and expansion provision
BS EN 13329 — Laminate floor coverings: elements with a surface layer based on aminoplastic thermosetting resins; specifications, requirements and test methods (the AC wear-class system derives from this standard)
BS 8203:2017 — Code of practice for installation of resilient floor coverings; the source of the hygrometer moisture-testing method also used for laminate over concrete
BS 8204-1 — Screeds, bases and in situ floorings; concrete bases and cementitious levelling screeds (subfloor tolerances)
BS EN 1264 series — Water-based surface embedded heating and cooling systems; relevant to floor surface temperature limits where laminate is laid over wet UFH
Building Regulations 2010, Approved Document E — resistance to the passage of sound; relevant where a floating floor is laid in a flat and acoustic underlay is specified
Building Regulations 2010, Approved Document C — resistance to moisture; the reason a ground-floor slab needs a damp-proof membrane or DPM underlay beneath a wood-based floor
Consumer Rights Act 2015 — goods and services must be of satisfactory quality and fitted with reasonable care and skill; the legal basis of a customer's complaint if the floor fails
BSI Knowledge — BS 8201:2011 — code of practice for installation of wood and wood-based panel flooring
The Contract Flooring Association (CFA) — guidance notes on subfloor preparation and moisture testing
GOV.UK — Approved Document E: Resistance to sound — floating floors and impact sound
GOV.UK — Approved Document C: Site preparation and resistance to contaminants and moisture — ground floor moisture requirements
European Producers of Laminate Flooring (EPLF) — AC wear-class system and installation guidance referenced by UK manufacturers
Consumer Rights Act 2015 — legislation.gov.uk — satisfactory quality and reasonable care and skill
laminate flooring installation guide — the installation method: acclimatisation, expansion gaps, setting out and finishing
lvt vs laminate comparison — when to steer the customer to vinyl plank instead
subfloor preparation guide — flatness, moisture and repair methods by subfloor type
floor levelling compounds — selecting and laying levelling compound
acoustic underlay selection — underlay choice for flats and upper floors
lvt installation pricing guide — the sister pricing guide for LVT and SPC
wood flooring installation pricing guide — pricing solid and engineered wood by comparison
carpet fitting pricing guide — pricing the floor you are usually replacing