Summary
Replacing a kitchen sink sits in the awkward band between a plumbing repair and a kitchen fitting job. The plumbing is simple — two supplies, one waste, possibly an appliance spur — but the sink is set into a worktop that may be laminate, solid timber, quartz, granite or composite, and the cut-out, the clips, the sealant and the state of the chipboard underneath decide how long the job takes far more than the pipework does. A plumber who quotes an hour and a half because "it's just a sink" finds the old sink siliconed in with the worktop, the tap nuts rusted onto the back of the bowl where no spanner reaches, the 40 mm waste glued into a pipe that crumbles, and a cut-out 10 mm too small for the new sink the customer bought online.
This guide prices the common versions of the job for 2026: inset stainless or composite like-for-like, inset with a size change needing the worktop cut, undermount into stone, and Belfast into a cabinet. It covers the labour times, the materials and what to mark them up, the regulations that actually apply — the Water Supply (Water Fittings) Regulations 1999, Approved Document H for the waste, and the Consumer Rights Act for the quote — and the extras that should be on the quote before the first nut is undone. For the method, see kitchen sink installation; for the pipework detail, kitchen waste and supply connections.
Key Facts
- Like-for-like inset sink and tap, labour — £150–£300 regionally, £180–£340 South East, £200–£380 London; 2–4 hours including removing the old, cleaning the cut-out, fitting, connecting and testing
- Inset with new or enlarged cut-out (laminate worktop) — add 1–2 hours and £60–£140; a jigsaw cut needs the edge sealed with silicone or a sealing strip to stop the chipboard swelling
- Undermount into quartz or granite — the stone fabricator cuts and polishes the hole (£150–£350 as a template-and-cut service) or the sink goes in during the worktop installation; the plumber's part is 2–3 hours
- Belfast or butler sink — 4–7 hours including the support frame or cabinet modification, the worktop cut around the sink, and the plumbing; £300–£550 labour plus a joiner if the cabinet needs rebuilding
- Sinks, trade price — stainless inset single bowl £60–£150, 1.5 bowl £90–£250; composite (granite/quartz resin) £150–£450; ceramic Belfast 600 mm £200–£500; undermount stainless £120–£350
- Taps — basic monobloc mixer £40–£90; mid-range £90–£200; pull-out spray or boiling-water tap £200–£1,200 (boiling-water taps are a separate job with a tank and a 13 A supply)
- Waste and trap — 90 mm basket strainer waste £10–£30; 1.5-bowl waste kit with overflow £25–£50; 40 mm bottle or tubular trap £8–£20; appliance trap with spigots £15–£25
- Connectors and valves — 15 mm flexible tap connectors with isolation valves £6–£15 a pair; WRAS-approved flexis only; replace, never reuse
- Materials markup — 15–25% on the sink, tap and sundries, or supply at cost with the labour rate carrying the margin; see markup to margin explained
- Customer-supplied sink — common; add a line for checking it against the cut-out before the old sink comes out, and exclude the cost of a return trip if it does not fit
- Water Regulations — hot and cold supplies need an accessible isolation valve each (Schedule 2 para 10); an appliance spur needs a double check valve or the appliance's own approved backflow protection (fluid category 3); a tap with a spray hose that can reach a bowl may need a check valve on both supplies
- Waste — 40 mm pipe and a 75 mm seal trap for a kitchen sink under Approved Document H1 (Table 1 in the current edition); maximum unventilated branch 3 m for 40 mm at a fall of 18–90 mm/m
- Overflow — a sink with an overflow must have it connected to the waste; a sink without one is acceptable but should be pointed out to the customer
- Sealant — neutral-cure or kitchen-grade silicone with fungicide between the sink rim and the worktop; the chipboard edge of a laminate cut-out sealed before the sink goes in
- Testing — fill and drain each bowl, check the trap and both connectors under pressure, run the dishwasher or washing machine if connected to the new trap, and leave the cupboard dry with a paper towel under the trap overnight (the customer checks it)
- VAT — standard rate; the job is a repair/improvement in an existing dwelling
- Consumer Rights Act 2015 — the sink must be fitted with reasonable care and skill; a written quote with the extras listed is the protection
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Labour time | Labour (regional) | Labour (London) | Materials (supplied) | Notes |
|---|---|---|---|---|---|
| Inset stainless, like-for-like, tap and waste | 2–3 h | £150–£250 | £200–£330 | £120–£300 | Same cut-out, same tap hole |
| Inset composite, like-for-like | 2.5–4 h | £180–£300 | £230–£380 | £220–£550 | Heavier; clips differ |
| Inset, new/enlarged cut-out in laminate | 3–5 h | £220–£380 | £280–£480 | £140–£350 | Jigsaw, edge sealing |
| Undermount into stone (hole pre-cut) | 2–3 h | £160–£280 | £220–£350 | £180–£450 | Fabricator cuts hole |
| Belfast into existing cabinet | 4–7 h | £300–£550 | £380–£680 | £300–£700 | Support frame; worktop scribe |
| Tap only (sink stays) | 1–1.5 h | £80–£150 | £100–£180 | £50–£300 | Seized nuts are the risk |
| Waste and trap only | 0.5–1 h | £60–£110 | £80–£130 | £20–£50 | Often an add-on to a leak call |
| Add dishwasher/washing machine spur to new trap | +0.5 h | +£40–£70 | +£50–£90 | +£20–£40 | Check valve, isolation |
| Boiling-water tap (tank, filter, 13 A socket) | 2–4 h | £200–£400 | £250–£480 | £600–£1,500 | Electrician if no socket |
Detailed Guidance
What the job actually involves
A like-for-like inset replacement, done properly:
- Isolate hot and cold at the existing isolation valves (or at the stopcock if there are none — and then there will be new ones). Open the tap to drain.
- Disconnect the tap connectors, the waste, the overflow and any appliance spur. Cap the appliance connection if the appliance is staying disconnected.
- Release the clips under the sink, cut the silicone bead around the rim, lift the sink out. On an old sink the clips are often rusted solid and the silicone has bonded the rim to the laminate — allow 20–40 minutes on a 20-year-old sink.
- Clean the cut-out, scrape old sealant, check the chipboard: if it is swollen along the front edge the worktop is on its way out and the customer should be told now, not after the new sink is in.
- Fit the tap, the waste and the overflow to the new sink on the bench, where you can reach the nuts, not in the cupboard.
- Seal the cut-out edge, bead the rim, drop the sink in, fit and tighten the clips evenly, clean the squeeze-out.
- Connect the supplies with new flexible connectors and isolation valves; connect the waste with a new trap; reconnect the appliance spur with a check valve.
- Fill, drain, test under pressure, check every joint, run the appliance, dry everything and leave a paper towel.
Two to three hours when nothing fights back. The other hour in the range is for when something does.
Building the price: worked example
Inset 1.5-bowl stainless sink and monobloc tap, like-for-like, outside London, plumber at £45/hour (see plumber hourly rate guide):
Labour: 3 hours × £45 = £135
Collection / return to merchant, 0.5 h = £22
-----
Labour subtotal £157 → quote £170
Materials (trade cost):
1.5-bowl stainless inset sink £130
Monobloc mixer tap £75
1.5-bowl waste kit with overflow £32
Appliance trap, 40 mm £18
2 × flexi connectors with isolation valves £12
Double check valve for dishwasher spur £8
Silicone, PTFE, sealing strip £9
-----
Materials at cost £284
Markup 20% £57
Materials charged £341
Quote total (ex VAT) £511
A VAT-registered plumber adds 20%; a customer who has bought their own £130 sink online saves £57 of markup and is told so, with the line that a sink that does not fit the cut-out is a return visit at the hourly rate.
Composite, undermount and Belfast: where the time goes
Composite sinks are heavy (10–15 kg against 4–6 kg for stainless), the clips are a different pattern and the cut-out template is usually not the same as the stainless sink it replaces, even at the same nominal size. The bowl is often deeper, so the existing trap may now sit too low for the waste pipe through the wall; check the pipe height before quoting. Composite can crack if the clips are over-tightened or the sink is dropped: handle it like a ceramic.
Undermount sinks into quartz or granite depend on who cut the hole. On a new worktop the fabricator templates the sink and polishes the edge; the sink is bonded and clipped under the stone, normally by the fabricator, and the plumber connects it. Replacing an undermount in an existing stone top is a job for the fabricator unless the new sink matches the old cut-out exactly — a plumber cannot enlarge a quartz hole on site. Quote the plumbing and refer the stone work.
Belfast sinks sit on a frame or a purpose-made cabinet, with the worktop cut to fit around the front and sides. Replacing like-for-like with the same size is 3–4 hours; a change from an inset to a Belfast is a carpentry job first (£200–£400 for the cabinet modification and worktop scribing) and a plumbing job second. The bowl is 600 mm or 800 mm wide, 220–250 mm deep, and the waste exits lower than an inset sink's: check that the waste pipe can be lowered or re-routed with fall. The tap mounts on the worktop or a bridge, not the sink, so a new tap hole is cut in the worktop.
The regulations that apply
Water Supply (Water Fittings) Regulations 1999 (and the Scottish Water Byelaws 2014): every fitting must be of an appropriate quality (WRAS or equivalent approval is the easy evidence for flexis, valves and taps); each supply to the tap needs a servicing valve; backflow protection must match the fluid category — a dishwasher or washing machine is fluid category 3 and needs a double check valve or the appliance's own approved device, and a pull-out spray tap whose hose can reach into a filled bowl is a category 3 risk too, so fit check valves. Flexible connectors have a finite life; put new ones in, never reconnect the old.
Approved Document H1 (Foul water drainage): kitchen sink waste is 40 mm minimum with a 75 mm water seal trap; an unventilated 40 mm branch runs to 3 m maximum at a fall between 18 and 90 mm per metre (1:55 to 1:11); a branch longer than that or serving more than one appliance needs an air admittance valve or venting. A sink waste discharging to a gully outside should discharge below the grating and above the water level. See waste pipes.
Approved Document P: a boiling-water tap needs a fused spur or a socket in the cupboard; a new socket on an existing kitchen circuit is not notifiable in England since 2013, but a new circuit is. In a kitchen the socket must be positioned so the tank's cable and the water are kept apart. Use an electrician if there is no supply.
Consumer Rights Act 2015: the installation must be carried out with reasonable care and skill and the goods supplied must be of satisfactory quality; a customer-supplied sink that fails is not your warranty. State that in the quote.
The extras that must be on the quote
- Seized tap connectors or back nuts — a basin wrench rarely reaches a kitchen tap's back nut behind a deep bowl; the old tap may have to be cut off. Half an hour.
- Corroded or glued waste pipe — a 40 mm solvent-weld pipe that breaks at the wall becomes a core-through-the-wall job. Half to one hour plus pipe.
- No isolation valves — turning off at the stopcock and finding the stopcock does not close: a stopcock replacement or freeze kit, £60–£150.
- Worktop damage — swollen chipboard under the rim means the sink will not seal; either a sealing strip and a warning, or a new worktop.
- Cut-out does not fit the new sink — a laminate cut-out can be enlarged; a stone one cannot; a cut-out that is too big for a smaller sink needs a new worktop or a larger sink.
- Appliance spur not to regulations — a washing machine fed from a tee with no check valve is common in older kitchens; bring it up to standard while the pipework is open.
- Lead or galvanised supplies — on pre-1970s kitchens; replacement to copper or plastic is a separate priced job.
- Customer-supplied materials — check against the cut-out before the old sink comes out; exclude a return visit.
Charging the small versions
A tap-only replacement is the commonest version of this job and the one most often under-priced: an hour on the bench if the old nuts come off, two hours if they do not, and a £40–£90 tap the customer has bought. Charge a first-hour rate of £80–£150 with the seized-nut risk stated. A waste-and-trap replacement is the fix for the "cupboard is wet" call: £60–£110 including the trap, and the chance to spot the sink that should be replaced.
Frequently Asked Questions
How much does it cost to replace a kitchen sink in the UK?
For a like-for-like inset stainless sink and tap, £150–£300 labour outside London plus £120–£300 for the sink, tap, waste and connectors — £300–£600 all in, or more with a composite sink or a tap above the basic range. A Belfast sink or a new cut-out in the worktop is £450–£1,000 all in because the carpentry doubles the labour.
How long does it take to replace a kitchen sink?
Two to three hours when the new sink fits the existing cut-out and the old fittings come apart; four to five hours if the worktop needs cutting or the old sink is fighting back; four to seven hours for a Belfast. Quote three hours as standard and list the things that add time.
Can a plumber cut a new sink hole in a quartz worktop?
No — enlarging or cutting a hole in quartz or granite needs the fabricator's diamond tooling and a polished edge for an undermount. In a laminate or solid timber worktop a plumber or joiner can cut and seal a new hole on site. For stone, the sink has to match the existing cut-out, or the fabricator does the stone work.
Do I need a check valve on the dishwasher connection when I fit a new sink?
Yes if the appliance does not have its own approved backflow protection. A dishwasher or washing machine is fluid category 3 under the Water Fittings Regulations and needs a double check valve on the supply; most modern appliances have an approved device in the inlet hose, but a check valve at the spur costs £8 and removes the argument.
The customer has bought a sink online. Should I fit it?
Yes, with two things in writing: that you will check it against the cut-out before removing the old sink and that a sink that does not fit means a return visit at your hourly rate, and that the sink's quality and warranty are the supplier's, not yours. Charge the same labour; you lose the materials margin and the collection time, which is fair.
Regulations & Standards
Water Supply (Water Fittings) Regulations 1999 (SI 1999/1148) — fitting quality, servicing valves, backflow protection by fluid category; Scottish Water Byelaws 2014 equivalent
Building Regulations 2010, Approved Document H, Section H1 — foul water drainage; trap seal depths, branch pipe sizes and lengths
Building Regulations 2010, Approved Document P — electrical safety for boiling-water tap supplies
BS EN 806-1 to -5 — specifications for installations inside buildings conveying water for human consumption
BS 8558:2015 — guide to the design, installation, testing and maintenance of services supplying water for domestic use (complementary to BS EN 806)
BS EN 12056-2:2000 — gravity drainage systems inside buildings; sanitary pipework
BS EN 274-1:2002 — waste fittings for sanitary appliances; requirements
BS EN 200:2008 — sanitary tapware; single and mixer taps
BS EN 13310:2015+A1:2018 — kitchen sinks; functional requirements and test methods, including overflow and drainage performance for inset and undermount sinks
Consumer Rights Act 2015 — reasonable care and skill; satisfactory quality of goods supplied
Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013 (SI 2013/3134) — cancellation rights on contracts agreed in the home
Water Supply (Water Fittings) Regulations 1999 — legislation.gov.uk
WRAS — Water Regulations guidance and approved products — fitting approvals and backflow guidance
Consumer Rights Act 2015, Part 1 Chapter 4 — services — reasonable care and skill
CIPHE — Plumbing standards and guidance — Chartered Institute of Plumbing and Heating Engineering
kitchen sink installation — the fitting method step by step
kitchen waste and supply connections — supplies, appliance spurs and wastes under the sink
waste pipes — pipe sizes, falls and trap seals
plumber hourly rate guide — the hourly rate behind the labour figures
markup to margin explained — what 20% markup means for margin
quotes vs estimates — listing extras so the quote holds
outside tap installation — a companion small plumbing job priced the same way