Summary
The verge is the edge of a pitched roof at a gable, where the tiles meet the top of the wall. For a century the tiles were bedded on a mortar fillet over an undercloak of slate or fibre cement, and for a century the mortar cracked, fell out in lumps onto the path and let the wind lift the end tiles. Dry verge systems — interlocking uPVC or aluminium units that clip over each tile edge and screw to the batten ends, or a continuous roll that the tiles sit over — were a premium option in the 1990s and have been the normal repair since BS 5534 was revised in 2014 to require mechanical fixing of all perimeter tiles. A roofer asked to "re-point the verge" today should be quoting a dry verge: the mortar repair is cheaper for an afternoon and fails again within five years, and it does not meet the standard.
The job is straightforward on a sound roof: remove the old mortar and any loose tiles, check and replace the undercloak and the batten ends, fit the starter unit at the eaves, clip each verge unit up the slope, fit the apex cap, and seal. It gets expensive when the undercloak has gone, the batten ends have rotted, the verge tiles were cut too short to take the units, or the gable is three storeys up and the only access is a scaffold. This guide gives the materials and labour figures for 2026, the two system types and when each fits, a worked quote, the access options and their prices, and the regulatory position. For the systems themselves see dry verge and dry ridge systems and roof eaves verge; for the companion ridge job see dry ridge vs mortar bedded.
Key Facts
- Per verge, fitted — £300–£550 regionally, £350–£650 South East, £400–£750 London for a 6–8 m verge on a two-storey gable, excluding access; two verges on one gable £600–£1,100 regionally
- Per metre, fitted — £40–£70 regionally, £55–£95 London; the per-metre figure is how to price a bungalow verge (4–5 m), a dormer cheek or a long detached gable (9–12 m)
- Interlocking units — £3–£6 each trade; one unit per tile course, so 20–28 units per 6–8 m verge at a 345 mm gauge for interlocking tiles, 45–60 for plain tiles at 100 mm gauge; universal units fit most interlocking concrete tiles, profile-specific units match a particular tile; left- and right-hand units are different
- Continuous (roll) dry verge — £15–£30 per metre trade; a uPVC or GRP section fixed to the batten ends with a flexible flange that the tiles lap over; faster to fit on plain tiles and slates; some systems need the verge tiles to overhang the wall by 38–50 mm
- Starter and apex units — eaves starter £4–£10 each, ridge/apex cap £10–£25, ridge end cap for dry ridge £8–£20; one starter per verge, one apex per gable
- Undercloak — 150 mm fibre cement strip to BS EN 12467, £3–£6 per metre, bedded on the wall head or fixed to the batten ends; needed under every dry verge, and often rotten or missing on the roof being repaired
- Fixings — stainless or coated screws into the batten ends; 2–3 per unit on most systems; the batten must be sound for 100 mm from the end, which is the usual repair
- Labour — two people, 2–3 hours per 6–8 m verge after access is up, so a semi's gable (two verges) is a short day and a detached house (four verges) a long one; a roofer at £250–£320 a day plus a labourer at £150–£180 (see roofer day rate guide)
- Access — a mobile tower (hired £120–£250 a week, or owned) for a two-storey gable where the ground is firm and level; a scaffold for anything over 7 m to eaves, on a slope, over a conservatory or on a highway (£300–£800 for a gable-end lift); the HSE does not accept a ladder as a working platform for this job
- Waste — old mortar and broken tiles, 2–4 rubble sacks per verge; a skip is not usually needed
- Mortar removal — every bit, including the bedding under the end tiles; a dry verge fitted over old mortar sits proud and the units crack
- Matching tiles — verge tiles that were cut short or are cloaked (a special verge tile with a downturn) may not take a clip-on unit; allow for replacement tiles or a profile-specific system
- Dry ridge at the same time — if the ridge is mortar-bedded, the apex of the dry verge needs a dry ridge end or a bedded ridge end that will crack; price the ridge too (£25–£45 per metre fitted; see ridge tile rebedding)
- Building Regulations — a repair, not notifiable; if more than 50% of the roof covering is replaced the thermal element rule in Approved Document L applies to the roof, which a verge job does not trigger
- BS 5534:2014+A2:2018 — mechanical fixing of all perimeter tiles (verge, ridge, hip, eaves) in all wind zones; mortar is not an acceptable sole fixing
- BS 8000-6:2013 — workmanship for slating and tiling; verge detailing
- Wind — verge units are rated to the BS 5534 wind-load zones and exposure; in exposed and coastal sites check the manufacturer's data and the fixing frequency
- Guarantee — manufacturers give 10-year guarantees on the units (uPVC colour and UV stability); the roofer's workmanship guarantee is separate and should be written
- Materials markup — 20–30%; the materials are a small part of the price so the labour rate carries the margin
- Consumer Rights Act 2015 — reasonable care and skill; a written quote with the access, the exclusions and the guarantee
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Job | Time (two people, access up) | Materials (trade) | Charge (regional) | Charge (London) | Notes |
|---|---|---|---|---|---|
| One verge, 6–8 m, interlocking tiles, units | 2–3 h | £70–£150 | £300–£550 | £400–£750 | Excl. access |
| Semi gable, two verges | 5–6 h | £150–£300 | £600–£1,100 | £800–£1,400 | Excl. access |
| Detached, four verges | 1.5–2 days | £300–£600 | £1,200–£2,000 | £1,600–£2,800 | Excl. access |
| Bungalow verge, 4–5 m | 1.5–2 h | £50–£100 | £220–£380 | £280–£480 | Tower only |
| Plain tiles, per verge (more units) | 3–4 h | £120–£220 | £380–£650 | £480–£850 | 45–60 units |
| Continuous roll system, per verge | 2–3 h | £100–£220 | £320–£580 | £420–£780 | Suits slate and plain tile |
| Undercloak replacement, per verge | +1 h | +£25–£50 | +£60–£120 | +£80–£150 | Often needed |
| Batten end repair, per verge | +0.5–1 h | +£15–£40 | +£50–£100 | +£60–£130 | Splice new batten |
| Dry ridge added, per metre | — | £12–£22 | £25–£45 | £35–£60 | Same visit |
| Mobile tower, week hire | — | — | £120–£250 | £150–£300 | Plus delivery |
| Scaffold, gable-end lift | — | — | £300–£800 | £450–£1,100 | Two-storey; more if on a highway |
Detailed Guidance
Interlocking units or continuous roll: which to quote
Interlocking (clip-on) units are the standard retrofit for concrete interlocking tiles: each unit hooks over the edge of one tile and the next unit laps it, screwed to the batten end. Universal units fit most interlocking profiles with a tile thickness within their range; profile-specific units match a particular manufacturer's tile and look neater. Plain tiles need plain-tile units at the 100 mm gauge, which trebles the count. They are quick, forgiving of a verge that is not perfectly straight, and the one a customer expects to see.
Continuous (roll) systems are a length of uPVC or GRP section fixed along the batten ends with the tiles laid over its upstand; the tiles must overhang the wall by the amount the system needs (typically 38–50 mm), which is often not the case on a roof built for a mortar verge. They suit slate and plain tiles where individual units look fussy, and new roofs where the overhang is set to suit. On a retrofit, check the overhang before quoting a roll system; if the tiles are flush with the wall, it is interlocking units or a re-lay of the verge course.
Aluminium systems exist for both types at two to three times the uPVC price; worth quoting on a conservation area house or where the customer wants the verge to look like lead.
The job, step by step, and where the time goes
- Access: tower or scaffold to the verge at both eaves and apex; a tower on firm ground, tied, with the platform at the right height for the lower verge and moved up the slope as the work climbs — which is why two verges on a tall gable are slower than on a bungalow.
- Strip the old mortar with a bolster and a scraper, lift the verge tiles if they are bedded, clear the undercloak. Bag the rubble.
- Inspect: the undercloak (replace if cracked, missing or rotten slate), the batten ends (sound for 100 mm? splice if not), the verge tiles (whole, correct overhang, not cloaked), the bargeboard or wall head beneath.
- Fit new undercloak where needed, fix the starter unit at the eaves, re-lay any lifted verge tiles, clip each unit up the slope with its screws into the batten, fit the apex cap at the ridge, seal to the ridge end.
- Repeat on the other side; check the ridge end; clean down; remove access.
Two to three hours per verge for two people once the access is up, with the access itself taking an hour each end of the day on a tower. The allowances in the quote are for the things found at step 3, which cannot be seen from the ground.
Worked quote: semi-detached gable, two verges, regional
Two-storey semi, concrete interlocking tiles at 345 mm gauge, 7 m verges, mortar failing both sides, undercloak suspected poor on one side, firm level drive for a tower.
Materials:
Verge units: 2 × 21 units × £4.20 (L and R) = £176
Starters 2 × £7, apex cap £18 = £32
Undercloak 7 m × £4.50 (one side, allowance) = £32
Screws, sealant, batten offcut = £25
-----
Materials at cost £265
Markup 25% £66
Materials charged £331
Labour:
Roofer 1 day £300 + labourer 1 day £160 £460
Undercloak replacement one side, in the day —
Uplift for the second person's set-up, waste, clean £60
-----
Labour charged £520
Access:
Tower hire 2 days (weekly rate) + delivery £180
Waste: 6 rubble sacks to the tip £30
Quote (ex VAT) £1,061 → £1,060
(£530 per verge; £76 per metre)
Exclusions listed under the quote: replacement verge tiles if the existing are short or cracked (£4–£8 each, fitted at the hourly rate), batten repairs beyond one splice per side, dry ridge if the ridge is found to be loose (priced per metre), and a scaffold if the ground will not take a tower.
Access: the line that doubles the quote
A dry verge on a two-storey gable is working at height under the Work at Height Regulations 2005: the HSE's position is that a ladder is for access and short-duration light work, not a working platform for stripping mortar and screwing 40 units up a slope. A tower on firm, level ground (checked, tied and with the platform moved as the work climbs) is the economic answer for most semis and bungalows; a scaffold is needed for three-storey gables, sloping or soft ground, a gable over a conservatory or extension roof, or a gable on the pavement (with a council permit). Price the access as its own line so the customer sees that a £600 verge job on a scaffold costs £1,200 because of the scaffold, not the roofer — and so a customer who has a scaffold up for the windows next month can time the job. See working at height.
Dry ridge, bargeboards and the jobs sold alongside
The dry verge meets the ridge at the apex, and a mortar-bedded ridge end next to a new dry verge is the weak point: the apex cap is designed to work with a dry ridge end or a mechanically fixed ridge tile. If the ridge is loose or the mortar is going, quote the dry ridge at the same time (£25–£45 per metre fitted); the access is already there, which is the saving. Bargeboards and fascias on the same gable are the other natural add-on — a uPVC bargeboard replacement while the tower is up is £40–£70 per metre fitted; see fascia soffit guttering pricing guide and fascia soffit. A roofer who quotes the verge, the ridge and the bargeboard as three options on one visit sells more than one who quotes the verge alone.
When a dry verge is the wrong repair
- Cloaked verge tiles (a special tile with a downturned edge, common on some clay and concrete profiles): the clip-on unit will not fit; the options are a profile-specific system or leaving the cloaked verge mechanically fixed and re-bedded in a polymer-modified mortar with clips — the exception the standard allows for cloaked verges.
- Slates: a slate verge is mechanically fixed by the slate nails and an undercloak; a continuous dry verge system for slate exists, but a traditional slate verge with a lead or mortar-free detail is often the better repair.
- Listed buildings and conservation areas: a uPVC verge on a listed cottage needs consent and is likely to be refused; an aluminium or traditional detail is the quote.
- A roof that needs re-covering: a dry verge on a roof with 30% of the tiles delaminated is £1,000 the customer does not need to spend; say so and quote the roof.
Charging the inspection and the small repair
The "a lump of mortar fell off the roof" call is a survey from the ground with binoculars or a drone, a tower or ladder inspection if the customer wants a price for the whole verge, and the honest answer that a patch re-point is £120–£200 and will fail again, against a dry verge at £300–£550 that will not. Charge the survey if a tower is needed to do it (£60–£120, deducted from the job); most roofers do the ground inspection free and quote.
Frequently Asked Questions
How much does dry verge cost to fit in the UK?
£300–£550 per verge outside London and £400–£750 in London for a typical 6–8 m two-storey gable verge, so £600–£1,100 regionally for both sides of a semi, plus access at £120–£250 for a tower or £300–£800 for a scaffold. Materials are £70–£150 per verge; the labour and the access are most of the price.
Is dry verge better than mortar?
Yes for a repair. Mortar verges crack with the roof's movement and the weather and fail within 5–15 years; dry verge units are mechanically fixed to the battens, do not crack, and are the repair that meets BS 5534:2014+A2:2018, which requires all perimeter tiles to be mechanically fixed. The mortar re-point is cheaper on the day and fails again.
Do I need planning permission or Building Regulations for dry verge?
No: it is a repair to the existing roof and is not notifiable under Building Regulations, and it does not need planning permission on an ordinary house. In a conservation area or on a listed building, a uPVC verge may need consent and may be refused; an aluminium or traditional detail is the alternative.
Can dry verge be fitted from a ladder?
Not safely or within the Work at Height Regulations 2005: stripping mortar and fixing 20–60 units up a slope is sustained work, not the short-duration light work a ladder is allowed for. A mobile tower on firm level ground is the usual access for a two-storey gable; a scaffold for anything taller or awkward. Price the access as a separate line.
How long does dry verge take to fit?
Two to three hours per verge for two people once the access is up, so a semi-detached gable with two verges is a day including putting the tower up and down, and a detached house with four verges is a day and a half to two days. Undercloak or batten repairs found when the mortar comes off add an hour a side.
Regulations & Standards
BS 5534:2014+A2:2018 — slating and tiling for pitched roofs and vertical cladding; code of practice; mechanical fixing of verge, ridge and hip tiles; wind uplift and fixing specifications
BS 8000-6:2013 — workmanship on building sites; slating and tiling of roofs and claddings
BS EN 12467:2012+A2:2018 — fibre-cement flat sheets (undercloak)
BS EN 490:2011+A1:2014 and BS EN 1304:2013 — concrete and clay roofing tiles (verge tile specifications)
BS EN 13859-1:2014 — underlays for discontinuous roofing
Building Regulations 2010, Approved Document L, Volume 1 (2021) — thermal elements where more than 50% of a roof covering is replaced (not triggered by verge repairs)
Building Regulations 2010, Approved Document A — structure; batten and roof structure where repairs extend beyond the verge
Work at Height Regulations 2005 (SI 2005/735) — access and working platforms; ladders only for short-duration light work
Construction (Design and Management) Regulations 2015 (SI 2015/51) — contractor duties on domestic roofing work
Planning (Listed Buildings and Conservation Areas) Act 1990 — consent for material changes on listed buildings and in conservation areas
Consumer Rights Act 2015 and the Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013 — services and cancellation rights
NFRC Technical Bulletins — National Federation of Roofing Contractors guidance on dry-fix systems
BS 5534:2014+A2:2018 Slating and tiling for pitched roofs — BSI; mechanical fixing requirements
NFRC — Dry fix roofing systems guidance — National Federation of Roofing Contractors
HSE — Working at height: a brief guide (INDG401) — ladders, towers and scaffolds
HSE — Safe use of ladders and stepladders (INDG455) — short-duration work rule
PASMA — Mobile access towers guidance — tower assembly and use
Approved Document L, Volume 1: Dwellings — gov.uk; the 50% roof covering rule
dry verge and dry ridge systems — the systems and how they fix
roof eaves verge — verge and eaves detailing
dry ridge vs mortar bedded — the companion decision at the ridge
ridge tile rebedding — ridge pricing when it is done with the verge
tile batten spacing by pitch — gauge, and therefore unit count, by tile type
roofer day rate guide — the day rate behind the labour figures
fascia soffit guttering pricing guide — bargeboards and fascias on the same tower
working at height — access choices and the ladder rule