Summary
A customer ringing to say water is coming out of the light is frightened, and rightly: water in a ceiling rose or a downlight sits across the live and neutral terminals and the earth of the fitting, and the first person to reach up and touch it is standing on a wet floor. The call-out is therefore two jobs in one. The electrician's job is to make the installation safe and, later, prove it is safe to re-energise. The plumber's or roofer's job is to find where the water is coming from and stop it. A single multi-skilled tradesperson can do both, but the order matters: safe first, trace second, repair third, test and reinstate last.
The trace is where most time is lost. The fitting is the exit point, not the source. Water that reaches the back of a plasterboard ceiling runs along the top of the board until it finds a hole, and the hole it finds is the cable entry at the rose or the cut-out for a downlight. A bath waste leaking at the far corner of a bathroom can appear at a landing light three metres away. The leak is upstream of the light in the direction of fall of the joists, the cables or the pipes, and the quickest way to find it is to work out what is directly above and nearby, then run water tests one source at a time.
This guide covers the make-safe steps, a decision tree for the trace, the common sources by what is above the ceiling, the ceiling and electrical repairs, the test before re-energising, and what to charge.
Key Facts
- Isolate first — switch off the lighting circuit MCB and, if it cannot be identified with certainty, the main switch; do not operate the light switch in the room; do not touch the fitting; keep the household away from it
- RCD protection — BS 7671:2018+A2:2022 Regulation 411.3.4 requires additional RCD protection for lighting circuits in domestic premises on new work; many older installations have no RCD on lighting, which is why water in a rose is a live-contact risk rather than a nuisance trip
- Catch and relieve — a bucket under the drip; if the ceiling is bulging with pooled water, pierce the bulge with a screwdriver away from the fitting to let it drain under control rather than letting the board fail
- Water follows cables — the twin-and-earth to a ceiling rose runs along or through the joists and drops through a hole directly above the rose; water on the top of the board follows the cable down to the rose terminals
- Downlights are drains — a 70–90 mm cut-out is the biggest hole in the ceiling; water pooling on the board exits there first and runs through the lamp holder
- Direction of fall — joists run one way, the board is flat, the water goes where gravity and the first hole take it; the source is rarely more than one or two joist bays away unless the water has run along a pipe or a cable
- Bathroom above — in order of likelihood: bath or shower sealant failure at the wall, shower tray waste or tray-to-wall seal, bath waste and overflow, WC pan connector, basin waste, a pipe joint behind the bath panel
- Pipework — radiator valve glands and tails, compression joints on pipes notched into joists, soldered joints that have been disturbed, push-fit fittings that were never fully inserted, a frozen-then-thawed pipe
- Top floor — slipped or cracked tiles, failed flashing at a chimney or abutment, a blocked valley, a Velux flashing kit, condensation in the loft dripping from the underside of the felt, a loft tank overflowing or its float valve passing
- Boiler and appliances — boiler condensate or pressure-relief discharge in a loft or cupboard above, a washing machine or dishwasher on a first floor, an unvented cylinder tundish discharging
- Timing tells — drips only when a shower is run point to the shower; drips in rain to the roof; drips with the heating on to a radiator or pipe; a constant slow drip to a mains or cold-feed joint
- Stain shape — a brown ring that spreads evenly is a slow repeated wetting; a wet patch with no ring is fresh; a yellow-brown stain with a dark edge is old and may be from a previous leak the customer has forgotten
- Insulation-resistance test — before re-energising, test the circuit at 500 V d.c. between live conductors and earth with lamps removed and electronic equipment disconnected; BS 7671:2018+A2:2022 Table 61 requires a minimum of 1 MΩ, and a wet circuit will read far lower
- Replace, do not dry — a downlight, a plastic rose that has been full of water or a lamp holder with corroded contacts is replaced; terminals that have been wet corrode and loosen later
- Insurance — escape of water is a standard head of cover on home policies; the trace-and-access part is often a separate cover with its own limit; photograph everything and give the customer a written report
- Ceiling repair — a damp patch that dries flat is stain-blocked and painted; sagged, soft or stained board that does not dry flat is cut back to the joists and patched
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| When it drips | What is above | Most likely source | First check |
|---|---|---|---|
| Only when the shower or bath is used | Bathroom | Sealant at the tray or bath edge, tray waste, shower screen seal | Run the shower onto the wall and floor separately for 5 minutes each with a dry sheet below |
| After a bath empties | Bathroom | Bath waste or overflow, trap joint, waste pipe joint | Fill and empty with the bath panel off and a torch on the waste |
| After the WC is flushed | Bathroom or cloakroom | Pan connector, cistern-to-pan doughnut, flush pipe | Flush with dry tissue around the connector and under the cistern |
| In heavy rain only | Roof | Slipped tile, flashing, valley, roof window | Inspect from the loft during rain with a torch |
| In cold clear weather | Loft | Condensation on the underside of the felt or on a cold-water tank | Look for drip marks on the insulation in the loft |
| Heating on, especially first thing | Pipework | Radiator valve or tail, compression joint in the floor void | Dry tissue on every joint on the radiators above |
| Constant slow drip, all conditions | Mains or cold-feed pipework, tank overflow | Pinhole, joint, passing float valve | Check the loft tank level and overflow; listen at the stopcock with everything off |
| Only when an appliance runs | Washing machine, dishwasher, boiler | Hose, filter, condensate, pressure relief | Run the appliance and watch it |
Detailed Guidance
Step 1 — make it safe
Go to the consumer unit before you go to the light. Identify the lighting circuit; if the labelling is poor, switch off the main switch and accept that the house will be dark for a while. Lock off if you can; at the least, tape the MCB and tell everyone in the house not to touch it. Then, and only then, go to the room.
Do not operate the light switch; a wet switch drop is as dangerous as the rose. Put a bucket under the drip. Look at the ceiling for a bulge: a plasterboard ceiling will hold several litres before it sags, and when it fails it goes all at once. If there is a bulge, pierce it at its lowest point, well away from the fitting and the cable route, and let it drain into the bucket.
If the fitting is a downlight, do not try to remove it with water still coming through. If it is a pendant, do not pull the flex. Leave it until the circuit is proven dead with a voltage indicator tested on a proving unit before and after.
Water from a light fitting
|
Switch off lighting circuit at the CU (main switch if unsure)
|
Prove dead at the fitting with a tested voltage indicator
|
Catch the water; relieve any ceiling bulge away from the fitting
|
Is the drip continuous?
|
YES ---------> Mains, cold feed, tank or heating pipework.
| Turn off the stopcock: does it stop within an hour?
| YES -> mains-fed pipe or fitting above
| NO -> heating system, stored water, or roof
|
NO (intermittent)
|
What is directly above and one room each way?
|
Bathroom ------> Run each fixture in turn for 5 minutes,
| dry sheet below, 20 minutes between tests
Roof/loft -----> Torch inspection in the loft, in rain if possible;
| look for wet felt, tide marks, drips on insulation
Bedroom -------> Radiators and heating pipes in the floor void
|
Found it ---------> Repair, dry, test circuit, reinstate
Not found --------> Lift boards or cut an inspection hole in the
ceiling upstream of the fitting, in line with
the cable or pipe run
Step 2 — trace from what is above
Stand under the fitting and work out what is above it and within about two metres in each direction. Then test one source at a time with a dry towel or sheet laid on the floor below the ceiling patch and twenty minutes between tests so you can attribute the water.
Bathroom above. Start with the shower, because it is the commonest source and the one customers do not suspect. Run it onto the walls only, then onto the tray only. A failed silicone bead at the wall-to-tray or wall-to-bath junction lets water behind the tray every shower; the tray waste leaks only when the tray fills; the screen seal leaks only where the water hits it. Then the bath: fill it, check the overflow by filling to the overflow, empty it and watch the waste and trap with the panel off. Then the WC: flush and check the pan connector and the close-coupling. Then the basin. A leak that appears only with a particular fixture is found in half an hour this way; a leak that appears with all of them is a waste-pipe joint downstream of them.
Bedroom or landing above. The floor void carries heating pipes, and the radiators in the room above are the first suspects. Dry tissue on each valve gland, each tail and each union; look for the green crust on copper and the white crust on brass. If the pipes run under the floor in notches, a compression joint in a notch that has been stood on will weep. Lift a board at the joist bay above the light.
Top floor, roof above. Go into the loft with a torch, in rain if the leak is rain-related. Look for daylight through the tiles, a wet patch on the felt, water running down a rafter, a blocked or overflowing valley, and the flashing at any chimney or abutment. Follow the drip marks on the top of the insulation back to where they start. If the felt is uniformly damp on the underside with droplets and there is no daylight, it is condensation, not a leak, and the fix is ventilation (see condensation in loft). Check the cold-water storage cistern: a passing float valve that overflows onto the loft floor instead of through the overflow pipe is a classic source of a landing-light drip.
Cupboards and utility spaces above. A boiler's condensate pipe, pressure relief discharge or a leaking filling loop; an unvented cylinder tundish that has started to discharge; a washing machine hose. These show up at the kitchen or hall light below.
Step 3 — repair the source and dry the void
Repair the leak, then give the ceiling void time to dry before closing anything up. Plasterboard that has been soaked once will usually dry flat if it is allowed to; board that has been wet for days sags and is replaced. Loft insulation that is saturated is removed and replaced, because it does not dry and it carries the damp to the board. Timber joists dry on their own; check them with a moisture meter after a week if there is any sign of rot.
If an inspection hole was cut, leave it open until the void has dried, then patch it with a piece of board on noggins, tape and fill.
Step 4 — electrical inspection and test before re-energising
With the circuit still isolated, remove the fitting. A plastic ceiling rose or a lamp holder that has held water is replaced, not dried; the terminals corrode and loosen later. A downlight is replaced with the same fire rating as the original. Dry the cable ends, re-strip any conductor that shows green or black corrosion, and check the junction box or the loop-in rose above for the same.
Then test. With lamps out and any electronic drivers, smart switches or transformers disconnected, carry out an insulation-resistance test at 500 V d.c. between line and neutral joined together and earth, and between line and neutral. BS 7671:2018+A2:2022 Table 61 gives 1 MΩ as the minimum for a 230 V circuit; a sound dry lighting circuit reads well above 100 MΩ, and anything below about 2 MΩ says there is still water somewhere in the circuit, usually in a switch drop or a junction box you have not found yet. A continuity test on the protective conductor and a polarity check complete the picture. Record the results on a Minor Electrical Installation Works Certificate, which the customer's insurer will want to see.
Only then re-energise, and only the lighting circuit first, watching for an RCD trip.
Step 5 — the ceiling
A stain that has dried flat is sealed with a stain-blocking primer (an ordinary emulsion will let the brown bleed through) and painted. A patch that has sagged, or a board that is soft when pressed, is cut back to the centre line of the adjacent joists and replaced; tape, fill, sand, prime, paint. If the ceiling is lath and plaster, the plaster around a wetted area loses its key and comes away later; press it and cut back to sound keys.
Pricing
| Item | Typical charge (ex VAT, 2026) |
|---|---|
| Emergency electrical make-safe, isolate and prove dead, daytime | £80–£150 |
| Same, out of hours | £150–£250 |
| Leak trace, up to 2 hours including water tests | £120–£250 |
| Replace ceiling rose or pendant and test circuit, certificate | £90–£160 |
| Replace a downlight, like for like, and test | £60–£110 |
| Insulation-resistance test and Minor Works Certificate (standalone) | £60–£100 |
| Reseal a bath or shower tray | £80–£150 |
| Replace a bath waste and trap | £90–£160 |
| Repair a radiator valve or tail | £70–£130 |
| Refit a slipped tile or patch a flashing from a ladder | £120–£250 |
| Patch a plasterboard ceiling (up to 600 × 600 mm), fill and paint | £150–£300 |
| Replace a full ceiling in a bathroom (up to 6 m²) | £500–£900 |
Keep the make-safe and the trace as separate lines and give the customer a written note of where the water came from. The insurer pays for trace and access and for reinstatement, but only with a report that says what was found.
Frequently Asked Questions
The RCD tripped and the light went off by itself. Is it safe now?
Safer, but not safe. The RCD has disconnected the circuit, but it will reset if someone pushes it, and if the RCD covers more than the lighting circuit the household will be tempted to. Switch the lighting MCB off as well, label it, and treat the circuit as live until it is proven dead at the fitting. An RCD trip in these circumstances also tells you water has reached the earth path, so the fitting and probably the rose will need replacing.
The customer wants the light back on tonight. Can I just dry it with a hairdryer?
Not without the test. A fitting that has been wet may look dry and still read a few hundred kilohms to earth, which is a shock risk and, on a non-RCD circuit, an eventual fire risk as the tracking carbonises. If the insulation-resistance test passes after drying and the terminals are clean, the circuit can go back on with the fitting replaced; if it does not pass, the circuit stays off and the customer uses a lamp on a socket circuit until it does.
The leak only happens when it rains, but the loft is dry. Where is it?
Look at the walls, not the roof. Water entering through a cracked render band, a defective window head or a cavity tray can run down inside the wall and along the ceiling board from the perimeter, appearing at the first fitting in from the wall. Check the top of the external wall above the room in rain, and look for a wet patch at the top of the inside wall before you condemn the roof.
Do I need to replace all the loft insulation that got wet?
Replace any mineral wool that is saturated, because it holds water against the board and the joists for weeks and it loses most of its thermal performance when it has been wet. Insulation that is slightly damp on the surface from a single short leak dries if it is lifted and the loft is ventilated. Do not put the new insulation back until the board below is dry.
Regulations & Standards
BS 7671:2018+A2:2022 (IET Wiring Regulations) — Regulation 411.3.4 RCD protection for domestic lighting circuits; Chapter 64 inspection and testing; Table 61 minimum insulation resistance values; Regulation 522.3 external influences (water)
Electricity at Work Regulations 1989 — Regulation 12 and 13 on isolation and working dead; Regulation 4(4) on safe systems of work
GS38 (HSE) — electrical test equipment for use on low-voltage systems, including proving units and voltage indicators
Building Regulations 2010, Approved Document P — electrical safety in dwellings; replacing a damaged fitting is not notifiable
Building Regulations 2010, Approved Document C (C2 resistance to moisture) — the standard a repaired roof or wall must meet
BS 5250 — management of moisture in buildings, including loft condensation
BS EN 60598-1 — luminaires: general requirements and tests, including the IP rating a replacement fitting carries
Consumer Rights Act 2015 — reasonable care and skill in both the electrical and the leak repair
IET — Wiring Regulations BS 7671 and guidance — inspection, testing and RCD requirements
HSE — Electrical safety: GS38 electrical test equipment — safe proving-dead practice
Electrical Safety First — Best Practice Guide: safe isolation — safe isolation procedure
Association of British Insurers — Escape of water — what home insurance covers
GOV.UK — Approved Document C: site preparation and resistance to contaminants and moisture — moisture resistance requirements
damp patch on ceiling diagnosis — reading the stain before the water reaches a fitting
shower leaking through ceiling — the commonest bathroom source in detail
safe isolation procedure — proving dead properly
lighting circuits — how loop-in lighting is wired and where the junctions are
test and inspection procedures — insulation resistance and the other tests
roof leak only in heavy rain — tracing a roof source
condensation in loft — when it is not a leak at all