Summary
Hotpoint is, with Beko and Bosch, one of the three most common washing machine brands on UK domestic call-outs. Since Whirlpool acquired the Indesit group in 2014, Hotpoint, Indesit and Ariston front-loaders have shared the same electronic control architecture and the same F-code scheme, so a code learned on one brand transfers to the others. The scheme itself is older than that: the "Evo" family of controllers used on Hotpoint Aquarius, Aqualtis and WM-series machines has reported F01 to F18 for well over a decade.
The catch is that the meaning of several codes shifted between controller generations. Hotpoint's own service pages document a handful (F01, F02, F03, F05, F12, F15, F16, F18) and list the rest without explanation, and the independent repair trade disagrees on F04, F06, F07, F08 and F11 because older and newer platforms assigned them differently. This guide gives the meaning that applies to the majority of post-2010 machines, flags where the older meaning differs, and emphasises confirming the fault by test rather than by code alone.
Two UK-specific points matter more for Hotpoint than for any other brand. First, the Whirlpool door-lock recall of December 2019 (extended in 2020) covered around 519,000 Hotpoint and Indesit machines built between October 2014 and February 2018, where a component in the door lock can overheat when the heater runs. A door-lock symptom on a machine of that age is a recall check first and a repair second. Second, Hotpoint's brushed-motor models (older Aquarius and WMA ranges) wear carbon brushes, so F02 on a ten-year-old machine is usually a £15 brush set, not a motor.
Key Facts
- Code format — "F" plus two digits on LCD/LED display models; some models drop the "F" and show only the number. Non-display models flash the programme LEDs: count the flashes in one repeating group (seven flashes, pause, repeat = fault 7).
- Brands sharing the scheme — Hotpoint, Indesit, Ariston and Hotpoint-Ariston front-loaders and washer-dryers on the Whirlpool/Indesit Evo controller family.
- F01 electronic control board — on current models a main PCB fault (some functions not selectable); on older machines the same code meant a short-circuit motor triac on the board. Either way it is a board fault, but check the motor and wiring for the short that killed the triac before fitting a new board.
- F02 motor circuit — drum does not turn or turns intermittently; worn carbon brushes (brushed motors), a failed tachogenerator or an open winding. Brushes under about 10 mm are due for replacement.
- F03 NTC temperature sensor — wash does not heat, or stops with a code shortly into the heat phase; sensor open or short circuit, or its wiring.
- F05 drain / pump — water left in the drum after the cycle, door will not release. Blocked coin filter, kinked or siphoning drain hose, blocked pressure chamber, or a failed pump. The most common Hotpoint code by a distance.
- H2O water fill timeout — the machine has not seen water within its fill time: tap off, kinked inlet hose, blocked inlet filter, failed inlet valve, or water siphoning straight out through a drain hose pushed too far into the standpipe.
- F12 display/main board communication — the front control module and the main board are not talking; check the ribbon/harness between them before replacing either board.
- F15 heater control — heater relay or heater circuit fault; in hard-water areas a scaled element drawing the wrong current is the usual trigger.
- F16 drum lock — top-loading machines only; the drum position sensor cannot see the drum door.
- F18 internal data error — microprocessor or EEPROM communication fault on the main board; power-cycle once, then board replacement.
- Door-lock recall — Whirlpool recall of Hotpoint and Indesit machines manufactured October 2014 to February 2018; 0800 316 1442; free repair or replacement. Check the model number ("MOD" on the rear plate or inside the door) against the official list before touching a door lock on a machine of this age.
- Part P — repairing or replacing components inside an appliance is not notifiable; work on the socket outlet or circuit is. See part p implications smart home for the boundary.
- WEEE Regulations 2013 — a condemned machine goes through a registered take-back or WEEE waste route, not general waste.
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Code | Most likely meaning (post-2010 Evo platform) | Older/alternative meaning seen on some models | First check |
|---|---|---|---|
| F01 | Electronic control board fault | Motor triac short circuit | Check motor/wiring for short, then board |
| F02 | Motor circuit fault | Motor jammed / tacho | Carbon brushes, tacho resistance, drum turns by hand |
| F03 | NTC temperature sensor | — | NTC resistance (roughly 20 kΩ at 20 °C, falls with heat) |
| F04 | Pressure switch stuck on "empty" | Drain/pump | Pressure hose and chamber for sludge; pressure switch |
| F05 | Waste pipe blockage or pump | — | Coin filter, drain hose, standpipe, pump impeller |
| F06 | Door lock / control board | Drum/motor (some lists) | Door lock continuity; recall check if 2014–2018 build |
| F07 | Heater circuit / heater relay | Pressure switch | Element resistance (about 20–30 Ω) and earth leakage |
| F08 | Heater relay stuck / door interlock | — | Element and relay; door lock; recall check |
| F09 | Software / EEPROM setup error | — | Power-cycle; board reprogramme or replace |
| F10 | Pressure switch gives no signal (neither empty nor full) | No cold fill | Pressure switch and hose; inlet valve |
| F11 | Pump circuit fault (pump not responding) | Hot fill | Pump winding resistance and connector |
| F12 | Communication fault between display and main board | — | Interconnect harness and plugs |
| F13 | Dryer temperature sensor (washer-dryers) | — | Dryer NTC |
| F14 | Dryer heater (washer-dryers) | Water heating | Dryer element continuity |
| F15 | Heater control / dryer relay | — | Heater relay on main board; element |
| F16 | Drum lock position sensor (top-loaders) | — | Drum door closed; sensor |
| F17 | Door lock | Water level | Door lock; recall check |
| F18 | Internal data / microprocessor error | — | Power-cycle; main board |
| H2O | No water detected during fill | — | Tap, inlet hose, inlet filter, valve, siphoning |
Where two meanings are listed, confirm the fault by component test before ordering a part. The code tells you which branch to start on, not which part to buy.
Detailed Guidance
Decision tree
HOTPOINT SHOWS A CODE OR STOPS MID-CYCLE
==========================================
1. Record the code (or count the flashes twice) and note where
in the cycle it stopped: fill / wash / rinse / drain / spin.
Model number: "MOD" on rear rating plate or inside door frame.
2. Built Oct 2014 – Feb 2018 AND any door-lock symptom
(F06, F08, F17, door light, burning smell at door)?
YES -> STOP. Check productrecall.campaign.gov.uk and
Whirlpool 0800 316 1442 before repairing.
NO -> continue
3. Where did it stop?
FILL (H2O, F10, F04, no water) -> go to 4
WASH/HEAT (F03, F07, F08, F15, cold) -> go to 5
DRAIN (F05, F11, water in drum) -> go to 6
SPIN/MOTOR (F02, F01, drum still) -> go to 7
NO PATTERN (F01, F09, F12, F18) -> go to 8
4. FILL
- Tap fully open? Inlet hose kinked? Inlet filter gauze clear?
- Drain hose pushed >150 mm into standpipe or below the
water trap -> siphoning; reposition with the hook guide
- 230 V at inlet valve during fill but no flow -> valve
- No 230 V at valve -> pressure switch stuck "full" (F04/F10)
or board
5. HEAT
- Element resistance about 20–30 Ω; open circuit = element
- Element to earth > 1 MΩ; low = scaled/split element
(common in hard-water areas)
- NTC resistance roughly 20 kΩ at 20 °C, falling with heat
- Element and NTC good -> heater relay on main board (F15)
6. DRAIN
- Coin filter (front-bottom flap): clear debris
- Drain hose kinked, frozen, or into a blocked trap
- Pressure chamber/hose blocked with sludge (false F05)
- Pump impeller turns freely? Winding ~150–200 Ω?
- Pump good, no 230 V at pump during drain -> board (F11)
7. MOTOR
- Drum turns freely by hand? (bearing/seized = different job)
- Brushed motor: brushes < 10 mm -> replace pair
- Tacho coil resistance (tens of Ω) and magnet secure
- Motor plug burnt or wet -> repair, then board check
- All good, no drive -> main board (F01 triac)
8. CONTROL
- Isolate 2 minutes, restart; code returns immediately?
- F12: reseat display–main board harness
- F09/F18: board software fault; reprogramme or replace
- Any board swap: check for the wiring/component short
that may have killed the old one
F05: the drain branch in detail
F05 appears when the pressure switch does not report "empty" within the drain time limit. Work from the cheapest cause outward. Open the service flap at the bottom front, drain the residual water with the emergency hose, and remove the coin filter; hair grips, coins and bra wires are the usual culprits. Spin the pump impeller behind the filter housing with a finger: it should turn freely with slight magnetic cogging. Next check the drain hose for kinks and that it rises to at least 600 mm before entering the standpipe or under-sink spigot, with the spigot blank removed if it is a new installation. See dishwasher vs washing machine plumbing for standpipe and trap arrangements.
If the pump runs and the hose is clear but F05 persists, the fault is usually a false "not empty" signal: pull the pressure hose from the pressure chamber at the back of the drum and clear the sludge. Only once all of this is clean does a pump with correct winding resistance but no supply during drain point to the main board.
F02 and carbon brushes
Older Hotpoint machines use a universal brushed motor. Brushes wear to the point where contact becomes intermittent, the tachogenerator cannot confirm speed, and the board raises F02, typically first noticed as the drum refusing to turn at the start of a wash or failing to spin. With the machine isolated, remove the two brush holders from the motor; brushes worn below roughly 10 mm, chipped or stuck in the holder are replaced as a pair. Newer models with brushless (induction or direct-drive) motors cannot have brush wear; on those, F02 points at the tacho, the motor plug or the board.
Heating faults and UK water hardness
F03, F07, F08 and F15 all touch the heating circuit. A heating element that has split through limescale build-up (common across the South East, East Anglia and parts of the Midlands) leaks to earth, trips the RCD on heat, or draws the wrong current and raises a heater code. Test the element at its terminals: expect about 20 to 30 Ω across the terminals and at least 1 MΩ from either terminal to earth. The NTC usually sits in the element's rubber grommet and reads roughly 20 kΩ at room temperature, dropping sharply as it warms. Replace element and NTC together when the element is scaled; the sensor is cheap and the labour is the same.
H2O and water supply
H2O is a fill timeout, not a leak. Confirm the tap is open and the inlet hose is not trapped behind the machine, then unscrew the hose at the machine and clean the gauze filter in the inlet valve. Test the inlet valve: 230 V present on the solenoid during the fill phase with no water flow means the valve has failed; valves with two or three solenoids are replaced as a unit. If water enters but the code persists, look for siphoning: a drain hose pushed too far into the standpipe or lying below the trap lets water drain as fast as it fills. The Water Supply (Water Fittings) Regulations 1999 require backflow protection on appliance connections; most machines carry a built-in check valve, so do not fit a non-return valve on the inlet that could restrict flow.
Door-lock codes and the Whirlpool recall
F06, F08 and F17 are associated with the door lock on different platforms. The lock is a thermally actuated or solenoid interlock with a microswitch; test continuity across the switch with the door closed and check the striker alignment. On any Hotpoint or Indesit built between October 2014 and February 2018, however, the first step is the recall check. Whirlpool's recall covered around 519,000 machines (initially 42 models, extended in 2020 to add further models such as WMFG 741 G UK, WMAQG 741 P UK and WMAQC 641 P UK) because a door-lock component can overheat when the heater runs, with a fire risk. The remedy is a free repair or replacement from Whirlpool; a tradesperson should not fit a non-recall replacement lock and leave the machine in service.
Using the service test mode
Evo-platform Hotpoint and Indesit machines have a built-in test programme that steps through fill, heat, drain, motor and door lock and displays any stored fault codes. Entry is a button-and-dial sequence that differs by model and is documented in the service manual; it is worth learning for the ranges you see most, because it confirms the fault with the machine's own sensors rather than relying on the code the customer reported.
What to charge
| Job | Typical UK price (ex VAT, including parts) |
|---|---|
| Diagnostic visit and coin filter / hose clear (F05, H2O) | £60–£90 |
| Carbon brush pair, supplied and fitted (F02) | £70–£110 |
| Door interlock replacement (F06/F08/F17, non-recall machine) | £75–£120 |
| Heating element and NTC (F03/F07/F15) | £90–£140 |
| Drain pump (F05/F11) | £90–£150 |
| Inlet valve (H2O) | £80–£130 |
| Main control board (F01/F09/F12/F18) | £150–£260 |
Boards above about £180 on a machine over eight years old usually push the customer towards replacement; see washing machine installation pricing guide for install pricing if they do.
Frequently Asked Questions
Do Hotpoint and Indesit use the same error codes?
Yes. Both brands, along with Ariston, sit on the Whirlpool/Indesit Evo controller platform and report the same F01 to F18 scheme. Model-generation differences apply equally across the brands, so confirm by component test rather than assuming a code maps to one part.
The machine has no display. How do I read the code?
Count the flashes of the programme or start LED in one repeating group, confirm by watching the sequence twice, and note which other LEDs are lit (numbered from the left or top as LED 1, 2, 3 in service tables). A continuously flashing light with no pause is not a code. Seven flashes, pause, repeat is F07.
Why does the door stay locked after a code?
Most codes, and F05 in particular, leave water in the drum, and the interlock will not release until the pressure switch reports empty. Drain through the emergency hose behind the service flap, then the lock releases after its cool-down (one to two minutes on thermal locks).
Is a code on a 2016 Hotpoint a repair job or a recall job?
Check the recall list first. If the model is on it, the customer registers with Whirlpool for a free repair or replacement and you do not fit a door lock yourself. If it is not listed, diagnose and repair as normal. The recall covers machines manufactured October 2014 to February 2018 only.
Can I replace the main board without finding the original cause?
You can, but F01 in particular is frequently a board killed by a shorted motor, a wet motor plug or a leaking element. Test the motor, element and harness before fitting a £150-plus board or the new one may fail the same way.
Regulations & Standards
Electrical Equipment (Safety) Regulations 2016 — safety requirements for domestic electrical appliances placed on the UK market; the basis on which the Whirlpool door-lock recall was run.
General Product Safety Regulations 2005 — manufacturer recall and corrective-action duties for unsafe consumer products.
BS EN 60335-2-7 — particular safety requirements for washing machines.
BS 7671:2018+A2:2022 — the socket outlet and circuit supplying the machine; RCD protection to Regulation 411.3.3 where applicable.
Building Regulations Part P — repair within an appliance is not notifiable; alterations to the fixed wiring are.
Water Supply (Water Fittings) Regulations 1999 — backflow protection on appliance supply connections.
Waste Electrical and Electronic Equipment Regulations 2013 — disposal of condemned appliances.
Consumer Rights Act 2015 — the customer's rights against the retailer for a machine that fails within six years, relevant when advising on repair versus claim.
Hotpoint — Washing Machine Error Codes Troubleshooting Guide — official code list and meanings for F01, F02, F03, F05, F12, F15, F16 and F18.
GOV.UK — Whirlpool washing machine recall (Hotpoint and Indesit) — the official recall model checker.
Which? — Whirlpool announces recall of up to 519,000 Indesit and Hotpoint fire-risk washing machines — recall scope and dates.
Whitegoods Help — Hotpoint Washing Machine Error Codes — independent repair-trade code table and flashing-light guidance.
How-to-Repair — Error fault codes for Ariston, Hotpoint, Indesit washing machines — shared-platform code list and test-mode guidance.
GOV.UK — WEEE regulations for businesses — disposal duties.
washing machine error codes bosch — equivalent brand-specific guide for Bosch machines.
washing machine error codes samsung — equivalent brand-specific guide for Samsung machines.
washing machine not spinning — drain, balance and motor diagnosis behind spin failures.
washing machine leaking — leak diagnosis by cycle phase.
dishwasher vs washing machine plumbing — standpipe, trap and hose arrangements that cause H2O and F05.
washing machine installation pricing guide — pricing when the machine is replaced rather than repaired.