Summary
Awnings sell in the first warm week of May and get fitted in June, and the installers who do them well are usually window and door fitters, handymen with a van and a second pair of hands, or the awning retailer's own team. The job looks like four brackets and a lift, and on a sound brick wall with a clear run it is. The price goes wrong on the wall: a 1970s cavity wall with soft facing bricks, a rendered wall with nothing solid behind the render for the first 30 mm, a house with external wall insulation where the bracket needs a 100–150 mm stand-off into the structure, a timber-framed house where the brackets must find the studs or a fixing plate, or a bungalow where the awning has to clear a door head and a gutter in the same 300 mm.
A retracted awning hanging off four brackets is 30–80 kg; an extended awning in a gust is a sail, and the load on the brackets is multiplied several times. The brackets, fixings and wall are the engineering; the fabric and the motor are the shopping. This guide prices the awning types, the labour by size and complexity, the electrics, the fixings that change the price, the planning and regulatory context, and a worked quote. For the neighbouring jobs see pergola installation pricing guide and door canopy installation pricing guide.
Key Facts
- Manual open awning (no cassette), 2.5–3.5 m wide, 2–2.5 m projection — £300–£700 trade; labour £250–£400 (two people, 2–3 hours); fitted £550–£1,100
- Semi-cassette, manual or electric, 3.5–4.5 m wide, 2.5–3 m projection — £700–£2,200; labour £300–£550; fitted £1,000–£2,750
- Full cassette, electric, 4–6 m wide, 3–3.5 m projection — £1,800–£4,500; labour £400–£700; fitted £2,200–£5,200
- Sensors and automation — wind sensor (vibration or anemometer) £80–£200; sun sensor £80–£150; remote with timer £40–£120; smart-home receiver £80–£200. Fit a wind sensor on every electric awning over 4 m: it is the cheapest insurance against the frame coming off the wall
- Electric supply — most motors are 230 V, 100–250 W, on a 3 A or 5 A fused spur from an existing ring or radial. A spur from an existing circuit is not notifiable under Approved Document P (England, 2013 edition); a new circuit from the consumer unit is. The circuit must have 30 mA RCD protection — BS 7671 Regulation 411.3.3 requires it for socket-outlets up to 32 A and for mobile equipment used outdoors, and a circuit extended to a fixed outdoor load is RCD-protected as standard practice; use an IP66 weatherproof connection box outside
- Electrician's charge for the spur — £120–£250 if the installer is not electrically competent; include it as a line
- Brackets and fixings — wall brackets (2 for up to 3.5 m, 3 for 3.5–5 m, 4 for 5–6 m, per the manufacturer); M10 or M12 through-bolts or resin anchors 100–150 mm into solid masonry; stand-off brackets for EWI £40–£120 per bracket; roof/rafter brackets for soffit mounting £60–£150 per bracket
- Wall types — solid brick or dense block: resin anchors or sleeve anchors, straightforward. Cavity wall with soft facing bricks: resin anchors into the brick (not the joint), pull-test the first. Render over block: find the block depth with a test drill; fix through the render into the block with resin and a sleeve, or use a spreader plate. EWI (external wall insulation): stand-off brackets or thermally broken fixings into the substrate; never into the insulation. Timber frame: fixings into studs or a 150 mm × 25 mm fixing plate spanning two studs, through the breather membrane with a sealed penetration. Hollow block or aircrete: chemical anchors with mesh sleeves; derate the load
- Mounting heights — the front bar of an extended awning should finish 2.0–2.2 m above the patio; the brackets therefore sit 2.5–3.0 m up on a wall with a 15° pitch over a 3 m projection. Check the door head, the window head and the gutter: a soffit or rafter mount is the alternative when the wall has no space
- Pitch — 10–15° minimum for rain run-off; a flatter awning holds water and the frame fails first
- Wind class — BS EN 13561:2015 classes 0–3; Class 1 ≈ Beaufort 4, Class 2 ≈ Beaufort 5 (fresh breeze, 29–38 km/h), Class 3 ≈ Beaufort 6. Specify Class 2 minimum for an exposed garden and retract above it; the data sheet states the tested class for each size
- Snow load — none; a retractable awning is retracted in winter; say so on the handover sheet
- Planning — on a dwellinghouse, a wall-mounted awning is normally permitted development as a minor external alteration; listed buildings need listed building consent; flats and maisonettes have no householder permitted development rights; a commercial awning with branding needs advertisement consent and a shopfront awning may need planning permission
- Building Regulations — not normally applicable to a domestic awning; the electrical work is Part P
- Access — brackets at 3 m on a flat patio are a step-ladder job for two; over a conservatory, a slope or a basement light-well it is a tower or a scaffold, priced as a line (Work at Height Regulations 2005)
- Guarantee — frames usually 3–5 years, motors 3–5 years, fabric 5–10 years against UV fading; your fixing guarantee is separate and should be stated (12 months is typical)
- Markup — 15–25% on the awning if you supply; many installers fit customer-supplied awnings at a higher labour rate and disclaim the product. See markup to margin explained
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Awning | Size | Trade price | Labour (2 people) | Fitted, regional | Fitted, London |
|---|---|---|---|---|---|
| Manual open, no cassette | 3 m × 2.5 m | £300–£700 | 2–3 h, £250–£400 | £550–£1,100 | £700–£1,300 |
| Manual semi-cassette | 3.5 m × 2.5 m | £500–£1,200 | 2–3 h, £280–£450 | £800–£1,650 | £950–£1,900 |
| Electric semi-cassette | 4 m × 3 m | £900–£2,200 | 3–4 h, £350–£550 + spur | £1,400–£3,000 | £1,650–£3,500 |
| Electric full cassette | 5 m × 3.5 m | £1,800–£4,000 | 3–5 h, £400–£650 + spur | £2,350–£4,900 | £2,700–£5,600 |
| Electric full cassette with sensors | 6 m × 3.5 m | £2,500–£4,500 | 4–5 h, £450–£700 + spur | £3,100–£5,400 | £3,500–£6,200 |
| Extras: EWI stand-off brackets | per bracket | £40–£120 | +30 min each | — | — |
| Extras: soffit/rafter brackets | per bracket | £60–£150 | +30–45 min each | — | — |
| Extras: fused spur by electrician | — | £15–£40 parts | 1–1.5 h | £120–£250 | £160–£300 |
| Extras: tower hire for a difficult elevation | — | £80–£150/day | — | — | — |
| Remove and dispose of old awning | — | — | 45–60 min | £60–£120 | £80–£150 |
Detailed Guidance
The survey: the wall decides the price
Measure the width available between obstructions (downpipes, lights, the neighbour's boundary, an outward-opening door), the height from patio to the underside of the gutter or soffit, and the position of the door and window heads. Then drill one 8 mm test hole where a bracket will go: it tells you render depth, brick or block hardness, and whether there is EWI or a cavity where you expected solid. Photograph the wall and note:
- Width and projection the customer wants against the width and height available. A 3.5 m projection needs the brackets at about 3 m up for the front bar to clear 2.1 m at 15°.
- Wall construction from the test hole and the house age.
- Obstructions at bracket height: lights, cables, the gas meter box, vents, satellite dishes. A soil vent pipe in the bracket position moves the awning or the pipe.
- Power — the nearest socket or circuit on the inside face of the wall, and whether the customer accepts a surface-mounted cable outside.
- Exposure — a south-west facing garden on a hill is a Class 3 site; the awning catalogue's maximum sizes drop with exposure.
Fixings that hold, and the ones that do not
The manufacturer's bracket schedule gives the number of brackets by width and the minimum fixing specification; price to it, not below it.
| Wall | Fixing | Notes |
|---|---|---|
| Solid brick (9 inch), dense block | M10/M12 resin anchors 100 mm embedment, or sleeve anchors | Fix into the brick, 50 mm from any edge; the easiest wall |
| Cavity wall, good facing brick | M10/M12 resin anchors into the outer leaf, 90–100 mm | Outer leaf carries the load; pull-test the first bracket |
| Cavity wall, soft or perforated brick | Resin with mesh sleeves; or through-bolt to a spreader plate inside where accessible | Derate; add a bracket |
| Render on block | Test-drill to find block; resin anchor through render with a sleeve so the render is not loaded | Bridge soft render with a packer or a spreader plate |
| External wall insulation (EWI) | Stand-off brackets or thermally broken bracket systems fixed into the substrate; seal the penetrations | Never load the insulation or the render coat; the EWI installer's warranty may require their approved fixing |
| Timber frame | Coach screws into studs located by survey, or a 150 × 25 mm treated fixing plate across two studs | Seal every penetration through the breather membrane with tape and sealant |
| Aircrete block (lightweight) | Chemical anchors with mesh sleeves, or through-bolts | Pull-out values are low; extra bracket |
| Rafter or soffit mount | Rafter brackets through the soffit into rafters, or a fixing beam | Where the wall has no room; price the brackets and the ladder time |
A pull test on the first anchor to the manufacturer's stated load is good practice and takes five minutes with a proof-test tool; on a resin anchor allow the full cure time (30 minutes to several hours depending on temperature) before loading.
Electric awnings and the Part P line
The motor is in the roller tube and the cable exits at one end; it needs a 230 V supply via a fused spur or a switched outdoor socket, usually through the wall from an existing circuit. The rules:
- A spur from an existing circuit, including one that goes outside, is not notifiable under Approved Document P in England (2013 edition) — but it must comply with BS 7671:2018+A4:2026, which means 30 mA RCD protection for the circuit, an IP-rated enclosure for the outdoor connection (IP66 is the usual choice), and cable routed and protected to the regulations.
- A new circuit from the consumer unit is notifiable (competent person scheme or Building Control).
- Scotland, Wales and Northern Ireland: check the local requirements.
If the installer is not electrically competent, the spur is an electrician's line at £120–£250 and the awning installer makes the final connection in the weatherproof box only if trained to. Radio remote receivers are usually in the motor head; a hard-wired wall switch needs a cable chase inside.
Sensors: why they are not an upsell
A wind sensor retracts the awning automatically when the front bar vibrates beyond a threshold or when an anemometer reads above the set speed. On an electric awning over 4 m, fit one. The failure mode without it is the awning left out on a sunny morning that turns into a squall at 2 pm while the customer is at work; the brackets hold and the arms bend, or the brackets do not hold. A sun sensor extends the awning when the sun comes out and is a comfort item. A timer or smart-home receiver is a convenience. Price them as options, recommend the wind sensor in writing, and record the recommendation if the customer declines.
Planning, listed buildings and shops
On an ordinary house, a retractable awning on the rear or side elevation does not usually need planning permission; it is a minor alteration to the external appearance. Check two things before saying so in writing: whether the property is listed (listed building consent is needed for almost any fixed external addition), and whether an Article 4 direction in a conservation area removes permitted development rights for the elevation. Flats have no householder permitted development rights and need permission from the freeholder in any case. On a shop, a fixed or retractable awning that changes the shopfront is usually development needing planning permission, and any lettering or branding on the valance is an advertisement needing consent under the Town and Country Planning (Control of Advertisements) (England) Regulations 2007. Put "subject to any planning or landlord consent, which is the customer's responsibility" on every awning quote.
Worked quote: 4.5 m electric semi-cassette, brick semi, Nottingham
South-facing rear elevation, solid 9-inch brick on a 1930s semi, patio doors with the head at 2.1 m, gutter at 3.1 m. Customer wants an electric awning with a wind sensor; socket inside on the kitchen wall. Flat patio, step-ladder access.
Materials (supplied by installer):
Electric semi-cassette awning 4.5 m × 3.0 m, Class 2 (3 brackets) £1,650
Wind sensor £120
Resin anchors, M12 × 3 brackets × 4 fixings, resin cartridge £35
IP66 outdoor connection box, 1 m cable, sundries £25
£1,830
Markup 20% £366
Materials charged £2,196
Labour:
Two people, survey check, mark out, drill and resin 12 fixings,
cure, mount brackets, lift awning, align and secure, set limits,
pair remote and sensor, test, handover 4 h × 2 = 8 person-hours
8 h × £38 = £304 → charge £320
Electrician: fused spur from kitchen ring, through wall to IP66 box £160
Quote (ex VAT) £2,676
The handover sheet states: retract in winds above Beaufort 5 or when the sensor retracts it; retract in winter; do not extend in rain for long periods unless the pitch has been checked; fabric care; the guarantee terms.
What to exclude and what to say
- "Fixings into render, external wall insulation or timber frame may require stand-off or specialist brackets, quoted separately after a test drill."
- "Electrical connection from an existing circuit included / excluded; a new circuit is not included."
- "Planning, listed-building, freeholder or landlord consent is the customer's responsibility."
- "Access by step ladder from a level patio; a tower or scaffold for other situations is an additional line."
- "The awning is supplied with the manufacturer's guarantee; our fixing guarantee is 12 months."
Frequently Asked Questions
How much does it cost to have an awning fitted?
Labour alone is £250–£450 for a manual awning up to 4 m and £350–£600 for an electric one including the fused spur, London £350–£800. With the awning supplied, a manual 3 m awning is £550–£1,100 fitted, an electric semi-cassette at 4 m is £1,400–£3,000, and a full-cassette electric awning at 5–6 m with sensors is £2,350–£5,400.
Do I need planning permission for an awning?
On an ordinary house, usually not: a wall-mounted retractable awning is normally a permitted minor alteration. Listed buildings need listed building consent, conservation areas with an Article 4 direction may need permission, flats need the freeholder's agreement, and shops generally need planning permission for a shopfront awning plus advertisement consent for any branding.
Can an awning be fitted to a rendered or insulated wall?
Yes, but not into the render or the insulation. On render over block, the fixings go through the render into the block with resin anchors and sleeves so the render carries no load. On external wall insulation, stand-off brackets or thermally broken bracket systems reach through to the structural wall; check the EWI installer's warranty terms. Both add £40–£120 per bracket and 30 minutes each.
How long does an awning installation take?
Two to three hours for a manual awning up to 3.5 m on a brick wall with two people, three to five hours for an electric awning including the spur and sensor set-up. Resin anchors need cure time before loading — up to a few hours in cold weather — so a difficult wall can turn it into a two-visit job.
What wind can an awning take?
Awnings are rated under BS EN 13561:2015 in wind classes 0–3: Class 2, the usual domestic minimum, is tested to about Beaufort 5 (29–38 km/h). Above that the awning should be retracted, which is why a wind sensor on an electric awning is worth its £80–£200. Larger sizes often carry a lower class; the data sheet gives the figure for the exact width and projection.
Regulations & Standards
BS EN 13561:2015 — external blinds and awnings; performance requirements including wind resistance classes and safety in use
BS EN 13120:2009+A1:2014 — internal blinds; performance and safety requirements (cord and chain safety, relevant where internal controls are fitted)
BS 7671:2018+A4:2026 — Requirements for Electrical Installations; RCD protection of circuits, outdoor connections, IP ratings
Building Regulations 2010, Approved Document P (2013 edition, England) — notifiable electrical work; new circuits versus additions to existing circuits
Town and Country Planning (General Permitted Development) (England) Order 2015 — Schedule 2, Part 1 householder permitted development; Article 4 directions
Planning (Listed Buildings and Conservation Areas) Act 1990 — listed building consent for fixed external additions
Town and Country Planning (Control of Advertisements) (England) Regulations 2007 — advertisement consent for branded commercial awnings
Work at Height Regulations 2005 (SI 2005/735) — ladder, tower and scaffold use for bracket fixing
Construction (Design and Management) Regulations 2015 — domestic client duties pass to the contractor; a two-person job is still a construction project
BS 8539:2012+A1:2021 — code of practice for the selection and installation of post-installed anchors in concrete and masonry; pull testing and anchor selection
Consumer Rights Act 2015 and Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013 — cooling-off and information duties for contracts agreed in the customer's home
Approved Document P: Electrical safety — dwellings — gov.uk; notifiable work
Planning Portal — Do you need permission? — householder permitted development guidance
Historic England — Listed building consent — fixed additions to listed buildings
HSE — Work at Height Regulations guidance — ladders and towers
Construction Fixings Association — BS 8539 guidance — anchor selection and testing in masonry
IET — BS 7671 Wiring Regulations — outdoor circuits and RCD protection
pergola installation pricing guide — the freestanding alternative
door canopy installation pricing guide — a fixed canopy over a door, similar fixings
electrician hourly rate guide — pricing the fused spur
part p notifiable work — when the electrics must be notified
markup to margin explained — margin on supplied awnings
conservation areas — Article 4 and listed-building checks
working at height — ladders, towers and the two-person lift