How Do I Calculate Pipe Flow Rates, Velocity & Pressure Drop for Domestic Plumbing?

Quick Answer: For domestic water supply, target a flow velocity of 1–3 m/s in copper pipes. Use the Hazen-Williams or Colebrook-White equation for pressure drop, or reference BS EN 806-3 design flow tables. A 22mm copper pipe (15mm internal diameter) at 2 m/s carries approximately 21 litres/minute; a 15mm pipe (13mm internal diameter) carries approximately 16 litres/minute at the same velocity.

Summary

Correct pipe sizing ensures adequate flow at all outlets without noise, erosion, or excessive pressure loss. Undersized pipes cause low pressure at taps and showers; oversized pipes are costly and slow to heat up. The fundamental relationship is between pipe bore, flow velocity, and flow rate — get one wrong and the whole system suffers.

In domestic plumbing, BS EN 806 Part 3 provides a simplified design method for sizing cold and hot water distribution pipework. It establishes design flow rates for each appliance type, uses a diversity factor to account for the fact that not all outlets run simultaneously, and sets maximum velocity limits to prevent noise and pipe erosion.

For central heating pipework, CIBSE Guide C and manufacturer data are the primary references. Heating circuits typically operate at 0.5–1.5 m/s, with lower velocities in smaller bore pipes to avoid pump noise.

Key Facts

Quick Reference Table

Got your quantities? squote builds the full quote with labour, materials and markup.

Try squote free →
Pipe Size Internal Bore Flow at 1 m/s (l/min) Flow at 2 m/s (l/min) Max Flow (3 m/s) (l/min)
15mm copper 13.6mm 8.7 17.4 26.1
22mm copper 20.2mm 19.2 38.4 57.6
28mm copper 26.2mm 32.3 64.6 96.9
35mm copper 32.6mm 50.0 100.0 150.0
25mm MDPE 20.4mm 19.6 39.2 58.8
32mm MDPE 26.2mm 32.3 64.6 96.9
Appliance Design Flow Rate (BS EN 806-3) Loading Units
Basin tap 0.1 l/s (6 l/min) 1
Bath tap 0.3 l/s (18 l/min) 3
WC cistern 0.1 l/s (6 l/min) 1
Shower (mixer) 0.1 l/s (6 l/min) 1
Kitchen sink 0.2 l/s (12 l/min) 2
Dishwasher 0.15 l/s (9 l/min) 2
Washing machine 0.15 l/s (9 l/min) 2

Detailed Guidance

Calculating Flow Rate from Velocity

The basic flow rate formula is:

Q = V × A

Where:

For a 22mm copper pipe (internal diameter 20.2mm = 0.0202m):

Practical conversion: 1 litre/second = 60 litres/minute = 16.67 gallons/minute

Using BS EN 806 Loading Units

Rather than calculating absolute flow rates for every outlet, BS EN 806-3 uses a loading unit system:

  1. Assign loading units to each outlet in the building (see table above)
  2. Total all loading units on the circuit being sized
  3. Convert to design flow rate using BS EN 806-3 Table 3 (the diversity curve)
  4. Size the pipe so that this design flow rate is achieved within velocity limits

This method inherently applies a diversity factor — a house with 15 loading units does not demand 15 × 6 l/min simultaneously.

Example: 3-bedroom house with 2 bathrooms:

Calculating Pressure Drop

Pressure drop in straight pipework can be calculated using simplified tables or formulae. For practical site use, the Darcy-Weisbach approach is most reliable:

ΔP = f × (L/D) × (ρV²/2)

Where:

For quick site calculations, use manufacturer pressure drop tables, which give Pa/m at various flow rates. A typical value for 22mm copper at 0.3 l/s is approximately 200–300 Pa/m (2–3 mbar/m).

Rule of thumb: Add 10–20% to calculated pipe length to account for fittings, or use the equivalent length method (add 0.5m per elbow, 1.0m per tee branch, etc.).

Sizing for Central Heating Circuits

Heating systems use slightly different criteria:

Example: Radiator circuit carrying 5 kW with 20°C temperature difference:

Noise and Erosion Limits

Exceeding velocity limits causes two problems:

  1. Erosion — particularly at bends and fittings, where turbulent flow scours the pipe wall. Hot water pipes erode faster. This is why 15mm hot water supply should be kept under 1.5 m/s.
  2. Flow noise — velocity over 3 m/s in cold water supply creates audible rushing/hissing in pipes. Often misidentified as water hammer. The fix is to upsize the pipe or add a pressure reducing valve.

Frequently Asked Questions

My customer has low pressure at a shower — how do I diagnose this?

Start at the source: check dynamic mains pressure at the stop cock under flow (a pressure gauge on a hose fitting works). If below 1.5 bar, the issue is supply pressure. If supply pressure is adequate, calculate the pressure loss through the supply pipe: measure total pipe length, count fittings, and use pressure drop tables. Often the problem is a long run of 15mm pipe that should be 22mm. Alternatively, a clogged strainer or partially closed isolation valve can cause dramatic pressure loss.

Should I design to the maximum velocity or a lower working velocity?

Design to a working velocity of 1–2 m/s for most domestic supply. Sizing to the 3 m/s maximum leaves no margin for additional outlets being added later and causes noise at the upper end. The maximum limits in BS EN 806 are absolute limits, not design targets.

Does pipe material affect flow rate significantly?

For the same bore and flow rate, plastic pipe (copper press fit, PEX, PB) has a slightly smoother internal surface than copper (lower roughness factor), meaning slightly less friction and pressure drop. In practice for domestic systems, the difference is small. The more significant factor is ensuring you use the manufacturer's stated internal diameter — a 22mm push-fit plastic pipe may have a different bore than 22mm copper.

How does hot water affect pipe sizing?

Hot water is less dense and less viscous than cold. This means higher velocity for the same flow rate and faster erosion. BS EN 806 recommends keeping hot water velocities below 1.5 m/s rather than the 3 m/s limit for cold. In practice, most domestic hot water pipes are sized conservatively at 15mm (hand basin, shower) and 22mm (bath, high-demand circuits) without detailed calculation.

What's the minimum flow rate I need at a thermostatic shower valve?

Check the manufacturer specification — most quality thermostatic shower valves require a minimum dynamic pressure of 0.5–1.0 bar and a minimum flow rate of 8–15 litres/minute. High-flow rain heads may need 25 l/min or more. This determines not only pipe sizing but whether a combi boiler or cold water storage system can deliver adequate flow.

Regulations & Standards