Summary
The close-coupled toilet is the standard UK WC: cheaper than back-to-wall or wall-hung, no concealed cistern, all the working parts accessible by lifting the cistern lid. Fitting one is a bread-and-butter plumbing job, and it is also the job where a surprising amount goes wrong: pans that rock, cistern-to-pan joints that weep, flush valves that run, pan connectors that leak at the base because the outlet height was wrong, and fill valves on the wrong side so the feed will not reach. Almost all of it comes from skipping the measuring at the start.
Two things have changed in recent years. First, flush volumes. A modern dual-flush close-coupled suite is 6/4 litres or 4.5/3 litres, and under Approved Document G a new dwelling has a water efficiency target (125 litres per person per day, or 110 litres where the local planning authority requires it) that makes 4.5/3 litre WCs the norm in new builds. Second, flush valves. Most suites now use a drop valve (a flush valve with a dual-flush button) rather than a siphon. Drop valves are easier to fit and give a dual flush, but they rely on a seal that wears and are the leading cause of a running toilet; many plumbers still prefer a siphon where a single flush is acceptable because it cannot leak into the pan.
The regulatory points are the Water Fittings Regulations (flush volume, approved fill valve with an air gap, backflow protection, warning pipe or internal overflow), Approved Document G (water efficiency in new dwellings, and the WC standards it calls up) and Approved Document H (connection to the soil stack). None of it is onerous, but a 7.5 litre single-flush siphon cistern bought cheap online is not compliant for a new installation.
Key Facts
- Pan outlet — horizontal (P-trap) is standard on modern pans; S-trap (vertical) pans are still made for older houses with a floor outlet; the outlet centre on most horizontal-outlet pans is about 180–190 mm above the finished floor but it varies by model, so measure the pan against the soil pipe before buying
- Pan connector — straight, 14° or 90° bent, offset, or flexible; flexible connectors are convenient but reduce flow and are not accepted by all installers for anything other than a short, straight run; a straight or offset rigid connector is better where it fits
- Soil pipe — 110 mm outside diameter (100 mm nominal) uPVC to BS EN 1329-1 or cast iron; the pan connector seals to the inside of the pipe with a lip seal, so the pipe end must be clean and undamaged
- Cistern connection — close-coupling plate and bolts with a doughnut (foam or rubber) washer between the cistern outlet and the pan; the washer seals the flush, the bolts hold the cistern, and the washer must not be overcompressed
- Flush volume — Water Fittings Regulations Schedule 2 paragraph 25: no single flush over 6 litres; dual-flush smaller flush no more than two-thirds of the larger; a cistern installed before 1 July 1999 may be replaced with one of similar volume
- Approved Document G — new dwellings: 125 litres per person per day (110 litres where the optional requirement applies), typically met with a 6/4 or 4.5/3 litre dual-flush WC; the WC must meet BS EN 997 and the flush volume is declared
- Fill valve — a side-entry or bottom-entry float valve to BS 1212-3 (diaphragm) or an approved compact fill valve, with a type AG air gap above the overflow level; must be WRAS-approved or equivalent
- Overflow — modern cisterns have an internal overflow that discharges into the pan through the flush valve; older cisterns need a 19 mm or 22 mm warning pipe to outside; a cistern with neither is not compliant
- Flush valve — siphon (single flush, cannot leak, replaceable diaphragm) or drop valve (dual flush, button operated, seal wears, can run)
- Feed — 15 mm copper or plastic with an isolation valve within reach, flexible tap connector to the fill valve tail (½" BSP); mains or cistern-fed cold is acceptable
- Pan fixing — two screws through the pan foot into the floor with plastic cups and rubber washers; never tighten hard into a ceramic pan; silicone around the base is optional and should be left open at the back for leak detection
- Floor — the pan must sit flat; pack a tiled or uneven floor with plastic packers and bed in silicone, not cement
- Seat — top-fixing or bottom-fixing hinges; soft-close seats are standard; check the seat fixing hole centres (usually 155 mm) match the pan
- Clearances — Approved Document M4(1) for new dwellings: a WC in an accessible WC compartment needs clear space in front; for an ordinary bathroom, 600 mm in front of the pan and 350 mm from the pan centre line to a side wall is the usual design minimum
- Ventilation — a bathroom or WC needs an extract fan (15 l/s) or an opening window under Approved Document F
- Not notifiable — replacing a WC is not Building Regulations work; a new WC where none existed (a new downstairs cloakroom) is notifiable under Parts G and H for the drainage and water connections
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Step | Tools and materials | Time | Check before moving on |
|---|---|---|---|
| Isolate and drain | Isolation valve, bucket, sponge | 10 min | Feed dead, cistern empty |
| Remove old suite | Multi-tool or hacksaw, basin wrench, bag for the old pan | 20–40 min | Soil pipe end clean and undamaged |
| Measure and dry-fit | Tape, spirit level, pan connector | 15 min | Outlet aligns with soil pipe; cistern clears the wall; feed reaches the fill valve side |
| Fit cistern internals | Fill valve, flush valve, doughnut washer, coupling kit | 20 min | Valves tight, washer seated, bolts hand-tight plus a quarter turn |
| Couple cistern to pan | Coupling kit, spanner | 10 min | Cistern level, no rocking, washer compressed evenly |
| Connect pan to soil pipe | Pan connector, silicone lubricant | 10 min | Connector fully home, pan square to the wall |
| Fix pan to floor | Drill, screws, cups, washers, packers | 15 min | Pan does not rock; screws snug not tight |
| Connect feed | Isolation valve, flexible connector | 10 min | No leak at either end |
| Fill and test | — | 20 min | Fill valve stops at the mark; flush fully clears; no weep at the doughnut or pan connector; no running after flush |
| Seat and finishing | Seat, silicone | 15 min | Seat aligned; silicone left open at the rear |
Detailed Guidance
Measuring before you buy
Close-coupled suites differ in three dimensions that matter: the height of the pan outlet, the projection of the pan from the wall, and the width and depth of the cistern. Measure the existing soil pipe centre height from the finished floor, the distance from the wall to the centre of the pipe, and the position of the cold feed. A pan whose outlet is 20 mm higher than the pipe can be accommodated with an offset or flexible connector; 50 mm is a different pan or a modified soil connection.
Check the fill valve entry. Most modern cisterns are bottom entry with the valve in the centre or to one side; some are side entry with the hole on the left or right (usually both, with a blank). If the existing feed comes up on the right and the new cistern's inlet is on the left, you need a longer flexible or to move the feed.
For a replacement in an older house with a floor outlet (S-trap), buy an S-trap pan or a P-trap pan with a 90° connector that drops into the floor; the latter is common but the connector adds projection.
Removing the old suite
Isolate the feed and flush to empty the cistern; sponge out the rest. Disconnect the feed and the overflow if there is one. Undo the cistern from the wall (usually two screws) and the coupling bolts, and lift the cistern off. Unscrew the pan from the floor; if the screws are corroded, cut them with a multi-tool. If the pan is cemented to the floor, break the pan with a hammer (goggles, gloves, a dust sheet) rather than fight it. Pull the pan off the connector or soil pipe. Clean the end of the soil pipe thoroughly, remove the old pan connector, and inspect the pipe for cracks and the lip of the socket for damage. Stuff a rag in the pipe to keep sewer gas out while you work.
Assembling the cistern
Fit the flush valve or siphon first, with its large sealing washer inside the cistern and the backnut outside, hand-tight plus a quarter turn. Fit the fill valve with its washer and backnut, then set the float height so that the water level sits at the mark inside the cistern (usually 20–25 mm below the overflow). Fit the close-coupling bolts through the cistern base with their washers and the coupling plate, and press the doughnut washer onto the flush valve outlet. A dual-flush drop valve needs the overflow tube height set so that it is above the fill level but below the cistern lid.
Coupling the cistern to the pan
Lower the cistern onto the pan so the doughnut washer sits in the pan's inlet recess and the bolts pass through the pan's holes. From below, fit the wing nuts or nuts with their rubber washers and tighten evenly, alternating sides, until the cistern is firm and level. Overtightening cracks the pan or the cistern, and squashes the doughnut so it leaks; the cistern should not move when pushed but the bolts should not be straining. Check the cistern is level across its width and is sitting against the wall; fix it to the wall with the two screws and rubber washers, or pack it if the wall is not plumb.
Connecting to the soil pipe
Lubricate the pan connector's lip seal with silicone spray or washing-up liquid, push it fully onto the pan spigot, and offer the pan up so the connector enters the soil pipe. Push the pan back until the connector is fully home and the cistern touches the wall. If the connector is at an angle, the lip seal will not seat and the joint will leak on the first flush; this is the most common fault with flexible connectors.
Where the soil pipe is more than about 10 mm out of line with the pan outlet, use an offset connector rather than a flexible one. Where it is in a different plane altogether, modify the soil pipe with a solvent-weld bend rather than reaching with a flexible.
Fixing the pan
With the pan in position and square to the wall, mark the fixing holes, move the pan, drill the floor (6 mm plug in concrete or screed, pilot in timber), and refit. Use the plastic cups and rubber washers supplied; tighten until the pan is firm. On a tiled floor, bed the pan on a thin bead of silicone and pack any gap with plastic packers so that it cannot rock. A rocking pan works the pan connector loose and cracks the doughnut seal over time.
Seal around the base with sanitary silicone if the customer wants a clean line, leaving a 100 mm gap at the back so that any leak at the connector shows on the floor rather than pooling under the pan.
Connecting the feed and testing
Fit a 15 mm isolation valve on the feed if there is not one, then a flexible connector to the fill valve tail with its fibre washer. Open the valve slowly and watch the cistern fill: it should stop at the mark with no overflow. Flush several times. Check the pan clears fully, the cistern refills and stops, and the flush valve does not run (listen for a trickle after refill; dye in the cistern shows a passing seal). Check the doughnut joint, the pan connector and the feed connection for weeping with dry tissue after each flush, and again ten minutes later.
Fit the seat last, align it, and nip the fixings.
Common problems
| Problem | Cause | Fix |
|---|---|---|
| Weep at the cistern-to-pan joint | Doughnut washer misaligned or overcompressed; bolts uneven | Refit the washer, tighten evenly |
| Leak at the soil pipe on flushing | Pan connector not fully home or at an angle; damaged lip seal | Re-seat; replace the connector; offset instead of flexible |
| Toilet runs after refilling | Drop valve seal worn or debris; float set too high so water enters the overflow | Clean or replace the seal; reset the float |
| Weak flush | Flexible connector too long or kinked; drop valve flush volume set low; pan outlet partly blocked | Shorten or replace the connector; adjust the valve; clear the outlet |
| Pan rocks | Uneven floor; screws loose | Pack and bed; tighten |
| Cistern fills slowly | Isolation valve partly closed; fill valve filter blocked; low pressure | Open; clean; use a pressure-appropriate fill valve |
| Condensation on the cistern | Cold mains water, warm humid room | Ventilation; cistern liner; not a fault |
Pricing a toilet replacement in 2026
| Job | Typical price (labour and sundries) |
|---|---|
| Like-for-like close-coupled replacement, working isolation valve | £120–£200 |
| Replacement including new isolation valve and pan connector | £150–£240 |
| Replacement with soil pipe modification (new bend or offset) | £220–£380 |
| Replacement on a tiled floor with packing and new fixings | £160–£260 |
| Supply and fit a mid-range dual-flush suite | £350–£600 |
Suite prices range from £120 for a basic close-coupled to £400+ for a rimless, soft-close suite with a concealed-trap pan. See toilet replacement pricing guide for the full breakdown.
Frequently Asked Questions
Is a flexible pan connector acceptable?
Yes, where it is short, nearly straight and fully engaged at both ends. It is the right answer for a small misalignment. A long flexible connector with a tight bend reduces flush performance, collects waste, and is the first thing to leak. For an offset of more than about 10 mm use a rigid offset connector; for a different plane, modify the soil pipe.
Can I replace an old 9 litre or 7.5 litre cistern with the same volume?
The Water Fittings Regulations allow a cistern installed before 1 July 1999 to be replaced with one of "similar volume", single or dual flush. In practice you will struggle to buy a new 7.5 litre cistern, and a 6 litre or 6/4 litre replacement is the standard answer. A new installation (not a replacement) must not exceed 6 litres.
Siphon or drop valve?
A siphon cannot leak water into the pan, so it never "runs", and its diaphragm is cheap to replace; it gives a single full flush. A drop valve gives a dual flush, which saves water and is what Approved Document G expects in new dwellings, but its seal wears and a running toilet usually means the drop valve. For a landlord who wants reliability, a siphon with a dual-flush option (some are made) or a quality drop valve with a readily available seal.
Does the cistern need an external overflow pipe?
Not if it has an internal overflow, which almost all modern cisterns do: excess water goes into the pan via the flush valve. An older cistern without an internal overflow needs a warning pipe to outside. A cistern with neither does not comply with the Water Fittings Regulations.
Is fitting a toilet notifiable?
Replacing an existing toilet is not notifiable. Installing a toilet where there was none (a new cloakroom) involves new drainage and a new water connection and is notifiable under Parts G and H of the Building Regulations in England and Wales; the water undertaker may also need to be told under the Water Fittings Regulations where it is a new connection.
Regulations & Standards
Water Supply (Water Fittings) Regulations 1999 — Schedule 2 paragraph 25 (WC flushing volumes and cistern requirements), paragraph 15 (backflow prevention), Regulation 4 (fittings of appropriate quality)
Water Supply (Water Fittings) (Scotland) Byelaws 2014 — equivalent requirements in Scotland
Building Regulations 2010, Approved Document G (Sanitation, hot water safety and water efficiency), 2015 edition with 2016 amendments — Requirement G2 water efficiency in new dwellings, Requirement G4 sanitary conveniences
Building Regulations 2010, Approved Document H (Drainage and waste disposal) — H1 foul water drainage, connection of appliances to the stack
Building Regulations 2010, Approved Document F (Ventilation) — extract rates for bathrooms and WCs
Building Regulations 2010, Approved Document M, Volume 1 (Dwellings) — WC provision and clearances in new dwellings
BS EN 997:2018 — WC pans and WC suites with integral trap
BS 1212-3:1990 — Float operated valves: diaphragm type (plastic bodied) for cold water services
BS EN 1329-1:2020 — Plastics piping systems for soil and waste discharge: PVC-U
BS EN 12056-2:2000 — Gravity drainage systems inside buildings: sanitary pipework
BS 8000-0:2014 — Workmanship on construction sites: introduction and general principles
legislation.gov.uk — Water Supply (Water Fittings) Regulations 1999, Schedule 2 paragraph 25
GOV.UK — Approved Document G: Sanitation, hot water safety and water efficiency
Bathroom Manufacturers Association — Water efficiency and WC guidance
toilet types — close-coupled, back-to-wall, wall-hung and what each needs
back to wall vs close coupled toilet comparison — choosing between the two
toilet replacement pricing guide — pricing the job in full
toilet running — diagnosing a drop valve or fill valve that will not stop
toilet cistern not filling — fill valve and supply faults
part g sanitation — Approved Document G in detail
isolation valves — fitting the valve every WC should have