Summary

Respiratory protective equipment is the last line of defence against asbestos fibre inhalation. It must never be treated as a substitute for enclosure, wet methods, or other engineering controls — RPE is worn because residual airborne fibres remain even after all other controls are applied. Choosing the right RPE, fitting it correctly, and maintaining it properly are all legal requirements under the Control of Asbestos Regulations 2012 (CAR 2012) and the Respiratory Protective Equipment at Work (4th edition) HSE guidance (HSG53).

The UK system for classifying RPE uses the Assigned Protection Factor (APF) to compare different types. An APF of 20 means the RPE reduces the concentration of airborne fibres inside the mask to 1/20th of the ambient level. For work below the control limit of 0.1 f/cm³, an FFP3 disposable mask (APF 20) is generally adequate. For licensed removal work where concentrations can be significantly higher, full-face or PAPR systems with APFs of 40–2,000 are required.

A critical and frequently misunderstood point is that an RPE with high APF on paper provides no protection if it does not fit the wearer's face. For any tight-fitting facepiece (disposable FFP3, half-mask, or full-face mask), a face fit test conducted by a competent person is mandatory before the worker wears the RPE in a hazardous environment. Workers who cannot achieve an adequate face fit — due to facial hair, facial structure, or scarring — must use a loose-fitting alternative such as a PAPR hood or helmet.

Key Facts

  • Assigned Protection Factor (APF) — the ratio of ambient to in-mask concentration that RPE provides when correctly worn and fit-tested
  • FFP3 disposable half-mask — APF 20; adequate for NNLW and low-exposure asbestos tasks
  • Reusable half-mask with P3 filter — APF 20; better durability than disposable for recurring use
  • Full-face mask with P3 filter — APF 40; required for licensed asbestos removal work
  • P3 PAPR (powered air-purifying respirator) with full-face hood/helmet — APF 20–2,000 depending on design; used where fit testing is not possible or where high-protection loose-fitting option is needed
  • Fit testing — qualitative (QLFT) — uses a test substance (Bitrex or saccharin) to detect leakage by taste; applicable to half-masks and some full-face masks
  • Fit testing — quantitative (QNFT) — uses a particle counter or other instrument to measure leakage; more objective and required for full-face masks under most standards
  • Facial hair — any stubble between the sealing face of a tight-fitting mask and the skin will break the seal; clean-shaven on the sealing area is a requirement, not a preference
  • Spectacles — temple-arm spectacles break the seal on full-face masks; prescription inserts or contact lenses must be used instead
  • P3 filter colour code — white (plus the hazard colour for the gas component if combination filter); P3 is the highest particulate protection class
  • Filter change frequency — P3 filters in reusable masks do not have a defined life based on use; replace when resistance increases noticeably, when damaged, or after any asbestos exposure; disposable FFP3 masks are single-use
  • Storage — P3 filters and FFP3 masks must be stored in sealed bags away from contamination when not in use; do not store in vehicles without sealed containers
  • Donning and doffing — donning (putting on) RPE must occur before entering the work area; doffing (removing) must occur in the clean stage of the DCU after showering; removing RPE in a contaminated area is a decontamination failure
  • Pre-use check — every use of a reusable mask requires a positive pressure check and a negative pressure check to verify seal integrity
  • Disposable FFP3 disposal — used FFP3 masks are asbestos-contaminated waste and must be double-bagged and disposed of as hazardous waste (see asbestos waste disposal)
  • Training — CAR 2012 requires workers to be trained in the correct use of their specific RPE, not just RPE in general

Quick Reference Table

Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.

Try squote free →
RPE Type APF Fit Test Required Best Use Case
FFP3 disposable half-mask 20 Yes (face-fit test) NNLW, minor asbestos work, short duration
Reusable half-mask + P3 filter 20 Yes (face-fit test) Recurring NNLW, cost-effective for regular use
Full-face mask + P3 filter 40 Yes (QNFT) Licensed removal work in enclosure
P3 PAPR full-face (tight-fitting hood) 40 Yes Where higher APF needed, no beard
P3 PAPR loose-fitting hood/helmet 20 No Workers with beards, failed fit test
P3 PAPR loose-fitting visor 20 No Alternative loose-fitting option
P100 supplied-air (SCBA) 2,000 Yes High-risk environments, emergency use

Detailed Guidance

Understanding the APF System

The Assigned Protection Factor is the expected in-use protection when RPE is correctly selected, fitted, and worn by a trained user. It is derived from workplace performance studies, not just laboratory tests. A higher APF gives more protection, but this only holds if the RPE is properly fitted.

For asbestos work, the choice of APF is driven by:

  1. The type of asbestos material being disturbed
  2. The expected fibre concentration during the task
  3. Whether the task is licensed, NNLW, or non-notifiable non-licensed work
  4. The ability of the specific worker to achieve a face fit

Where fibre concentrations during work can be estimated (via air monitoring records from similar tasks), the required APF is calculated as: (estimated concentration) / (acceptable in-mask concentration). For most asbestos work, an APF of 20 (FFP3 or half-mask P3) is the minimum accepted by HSE. Licensed removal work, where concentrations during removal can far exceed the control limit, requires a minimum APF of 40 (full-face with P3).

FFP3 Disposable Half-Masks

FFP3 disposable masks are the most commonly used RPE for NNLW and minor asbestos tasks. They are single-use, must be worn correctly, and must not be reused after any asbestos exposure.

Key requirements:

  • CE marking and FFP3 classification: look for CE followed by the notified body number, and EN 149:2001+A1:2009 (the relevant European standard) [verify current applicable standard post-Brexit UK conformity marking requirements]
  • Nose piece: the adjustable nose piece must be formed to the nose bridge before the straps are adjusted; a gap at the nose is the most common failure point
  • Chin under the mask: the lower edge of the mask must sit under the chin; if worn above the chin, the seal is broken
  • Valve vs no-valve: valved FFP3 masks have an exhalation valve that reduces breathing resistance; unvalved masks provide slightly better environmental containment. For asbestos work, either is acceptable if correctly fitted
  • Size: FFP3 masks are not one-size-fits-all. Different manufacturers produce different sizes and shapes. The fit test result is mask-specific — a worker fit-tested on brand A cannot assume brand B fits the same

Disposable FFP3 masks should not be stored loose in tool bags or in vehicle gloveboxes. They should be kept in sealed polythene pouches until use, and any mask that has been opened and not immediately used should be checked for contamination before use.

Reusable Half-Masks with P3 Filters

Reusable half-masks offer better long-term value for workers who conduct asbestos tasks regularly. The mask body is cleaned and maintained between uses; only the filter cartridges are replaced.

Selection points:

  • Mask brand and filter compatibility: P3 filter cartridges are not interchangeable between manufacturers; use only the manufacturer's specified P3 filters for that mask model
  • Filter type: for asbestos-only work, a P3 particulate filter is sufficient. Combination P3/gas filters are used where other hazardous gases are present simultaneously (e.g. stripping asbestos lagging in a boiler room)
  • Seal check before every use: insert the filter, put on the mask, block the filter inlets and breathe in (negative pressure check) — the mask should crush inward and stay crushed for 10 seconds without air entering. Then block the exhalation valve and breathe out (positive pressure check) — no air should escape at the face seal
  • Cleaning: use manufacturer-approved wipes or solution; do not use solvents that can degrade the mask material; rinse thoroughly and allow to dry before storage
  • Inspection: check the mask body for cracks, the straps for deterioration, and the seal for any cuts or deformation before each use

Full-Face Masks with P3 Filters

Full-face masks provide an APF of 40 and are the standard for licensed asbestos removal work inside an enclosure. They cover the entire face — eyes, nose, and mouth — and provide eye protection in addition to respiratory protection.

Critically, full-face masks must be fit-tested using quantitative methods (QNFT). The most common QNFT method used in the UK is the ambient aerosol condensation nuclei counter method (PortaCount or equivalent). Qualitative fit tests using Bitrex are not approved for full-face masks in high-hazard environments.

Additional considerations:

  • Visor care: the visor scratches easily; replace visors when they become scratched to the point of restricting vision
  • Spectacles incompatibility: the arms of standard spectacles break the face seal. Workers who require vision correction must use prescription inserts (internal frames designed to clip inside the mask), contact lenses, or choose a PAPR with external visor
  • Communication: full-face masks significantly muffle speech; use of hand signals or radio communication may be needed inside an enclosure
  • Speech membranes: some full-face masks include a speech diaphragm to improve intelligibility; these must not be removed as they are part of the seal path

Powered Air-Purifying Respirators (PAPRs)

PAPRs use a battery-powered fan unit to draw air through HEPA (P3-equivalent) filters and deliver filtered air inside a hood, helmet, or tight-fitting facepiece. They are particularly valuable for workers who cannot achieve an adequate face fit.

Two categories relevant to asbestos work:

Loose-fitting PAPRs (hoods and helmets): These do not seal to the face, so there is no face-fit testing requirement. They have APFs of 20 (hood) to 40 (powered hood with constant flow), but the protection is achieved by positive pressure inside the hood rather than a face seal. Suitable for workers with beards or facial structures that prevent tight-fitting seal. The hood/helmet itself is disposable or cleanable between uses; filters are replaced at manufacturer's intervals.

Tight-fitting PAPRs: These use a full-face or half-mask facepiece connected to the powered fan. They do require fit testing. APF up to 2,000 for the highest-specification systems.

PAPR limitations for asbestos work:

  • Battery life — powered units need charged batteries; a battery failure mid-task inside an enclosure is a serious problem; always carry spare batteries
  • Bulk — hoods and helmets are bulkier than face masks; can restrict vision and movement in confined spaces
  • Heat — less of an issue with loose-fitting hoods (air flow assists cooling) than with tight-fitting full-face masks
  • Storage — the hood/helmet component should be stored clean and bagged; contaminated hoods are asbestos-contaminated waste

Face Fit Testing: What, Who, and How Often

Face fit testing is required by law for any tight-fitting RPE used in an environment where the wearer will be exposed to hazardous substances above the WEL. For asbestos work, this means all tight-fitting FFP3 masks, half-masks, and full-face masks must be fit-tested.

Who conducts the test: a competent person — typically an occupational hygienist, H&S officer, or trained fit tester. There is no formal UK certification for fit testers, but HSE guidance (HSG53) and the FitTest Register (a voluntary register) describe the competencies required.

When to retest:

  • Before first use of a new mask model (fit tests are mask-specific)
  • When the worker's facial features change significantly (significant weight gain/loss, dental surgery, scarring)
  • At intervals recommended by the employer's health and safety management system (typically 2 years for routine monitoring)
  • If the worker reports difficulty breathing or poor seal

What a pass means: the test result (quantitative: fit factor typically ≥100 for half-mask; ≥500 for full-face) means that specific mask, in that specific size, fits that specific worker. It does not mean any mask of that type fits them.

Records: fit test records should be retained by the employer. The worker should receive a copy and carry it when doing asbestos work, as HSE inspectors may request to see it.

Frequently Asked Questions

Can I wear my FFP3 mask over a beard?

No. Any stubble or beard growth on the sealing line of a tight-fitting mask will break the seal and nullify the protection. This is not a preference or a guideline — it is a physical fact that HSE's own guidance (HSG53) is explicit about. If you cannot be clean-shaven on the sealing area, you must use a loose-fitting PAPR hood or helmet. Tight-fitting masks do not function as advertised when worn over facial hair, regardless of the fit test result.

How do I know if my FFP3 mask is EN 149 compliant?

Look for the CE mark (or UKCA mark post-Brexit) and the standard number EN 149:2001+A1:2009 printed on the mask body. Also look for the FFP3 classification mark. The mask should also carry the notified body (NB) number that verified conformity. Counterfeit respiratory protective equipment is a significant problem — purchase from reputable industrial safety suppliers and check the manufacturer's website for authenticity guidance.

What is the difference between P3 and HEPA in relation to asbestos?

P3 is the European/UK classification for the highest level of particulate filter in an RPE system, defined under the EN standards for gas mask filter cartridges and half-mask filters. HEPA (High Efficiency Particulate Air) is a filter classification used for air purification systems, vacuum cleaners, and NPU units. P3 filters meet or exceed HEPA H13 standard in terms of filtration efficiency (99.95% at 0.3 µm). For practical purposes: P3 is the term for the filter in your respirator mask; HEPA is the term for filters in your NPU and vacuum cleaner. Both are appropriate for asbestos use in their respective applications.

My employer says I don't need a fit test for a disposable FFP3. Is that correct?

No. Fit testing is required for all tight-fitting RPE used in a hazardous environment, including disposable FFP3 masks. The Control of Asbestos Regulations 2012 Regulation 11(6) and HSE guidance (HSG53) are clear on this point. An employer who says fit testing is not required for FFP3 disposable masks is incorrect, and this could constitute a breach of CAR 2012. If you are doing NNLW or any asbestos work and have not been fit-tested, you should raise this with your employer as a matter of urgency.

How should I dispose of my used FFP3 mask after asbestos work?

A used FFP3 mask — whether from NNLW or licensed work — is asbestos-contaminated waste. Remove it in the dirty end of the decontamination unit (not outside the work area), place it immediately into the asbestos waste bag, and seal the bag. Do not carry it home, leave it in your van, or put it in a general waste bin. Treat it identically to any other asbestos waste — double-bag, label, and dispose of via registered carrier and permitted facility. See asbestos waste disposal for full disposal requirements.

Regulations & Standards

  • Control of Asbestos Regulations 2012 (SI 2012/632) — Regulation 11 (prevention or reduction of exposure); includes RPE requirements

  • L143 Managing and Working with Asbestos ACoP — HSE guidance including RPE selection tables

  • HSG53 — Respiratory Protective Equipment at Work (4th edition) — HSE guidance on RPE selection, fit testing, and maintenance; primary reference for all RPE decisions

  • EN 149:2001+A1:2009 — European standard for filtering half masks; defines FFP1, FFP2, FFP3 classifications

  • EN 136 — European standard for full-face masks

  • EN 12941 / EN 12942 — European standards for powered air-purifying respirators

  • EN 143 — European standard for particulate filters including P3 classification

  • PUWER 1998 (Provision and Use of Work Equipment Regulations) — maintenance and inspection obligations apply to reusable RPE as work equipment

  • HSG53 Respiratory Protective Equipment at Work — HSE guidance; primary RPE reference

  • L143 Managing and Working with Asbestos ACoP — RPE tables and asbestos-specific guidance

  • HSE RPE guidance pages — selection tools and fit test information

  • British Safety Industry Federation (BSIF) RPE guidance — industry body for RPE; fit test competency guidance

  • notifiable non licensed work nnlw — RPE requirements for NNLW tasks

  • asbestos removal enclosure setup — RPE use within enclosures

  • asbestos waste disposal — disposing of used RPE and PPE

  • asbestos in textured coatings — RPE selection for textured coating removal