Summary
S-Plan and Y-Plan are the two layouts almost every wet central heating system with a stored hot water cylinder in the UK follows. The names come from Honeywell's "Sundial" plans from the 1970s and have stuck even though the valves are now made by half a dozen manufacturers. If you work on boilers, cylinders or heating controls you need to be able to look at a wiring centre and know which plan you are standing in front of, because the fault-finding logic is different.
The physical difference is simple. S-Plan has a 2-port valve on each circuit — one on the flow to the cylinder coil, one on the flow to the radiators, and more if the house is zoned — and each valve has a micro-switch that closes when the valve is fully open. Those switches, in parallel, are what tell the boiler and pump to run. Y-Plan has a single 3-port valve at the point where the flow splits, with one inlet and two outlets, and the valve head moves between three positions: hot water only (its spring-return rest position), mid-position (both), and heating only. One micro-switch inside the head provides the boiler and pump call.
The consequence for the customer is that S-Plan gives full zoning and a real interlock on every zone, which is why it is the default for new installations and for anything that needs to meet the 2021 Approved Document L requirements. Y-Plan was the cheaper choice for decades and millions remain in service; it works well but it cannot easily be extended to three zones, its mid-position logic confuses people, and a tired valve produces a characteristic set of symptoms that get misdiagnosed as boiler faults.
Key Facts
- S-Plan — two or more 2-port spring-return motorised valves (commonly 22 mm, 28 mm on larger systems), one per zone, with the valve end switches wired in parallel to call the boiler and pump
- Y-Plan — one 3-port mid-position valve on the common flow: port AB inlet, port A to the hot water cylinder, port B to the heating; the valve rests on port A (hot water) and is driven by a synchronous motor towards B
- W-Plan (less common) — a 3-port diverter valve giving hot water priority: either hot water or heating, never both
- 2-port valve wiring (Honeywell V4043 convention) — brown: motor live (from the zone's stat and programmer); blue: neutral; grey: end switch common (fed from permanent live or the demand live, depending on the diagram); orange: end switch output to boiler and pump; green/yellow: earth
- 3-port valve wiring (Honeywell V4073 convention) — grey: hot water "off/satisfied" signal; white: heating "on" demand; orange: boiler and pump output; blue: neutral; green/yellow: earth
- Boiler interlock — Approved Document L 2021 (England) and the Domestic Building Services Compliance Guide require a boiler interlock so that the boiler does not fire when no zone is calling; in S-Plan the valve end switches provide it, in Y-Plan the single valve micro-switch does
- Zoning — Approved Document L requires separate time and temperature control for space heating and hot water, and dwellings over 150 m² floor area need at least two space-heating zones with independent time and temperature control: S-Plan with a third valve is the usual answer
- Cylinder thermostat — surface-mounted on the cylinder about a third of the way up, set to 60–65 °C; a 2-terminal or 3-terminal stat (common, call, satisfied) is used in Y-Plan to drive the grey wire
- Room thermostat — one per heating zone; smart or programmable thermostats replace the programmer and stat with a single device but the valve wiring is unchanged
- Programmer — 2-channel (HW and CH) with "HW off" terminal needed on Y-Plan with some valves; a 3-channel programmer is used for S-Plan with two heating zones
- Manual lever — both valve types have a manual override lever to open the valve for filling and venting; a lever that will not move indicates a seized spindle or a jammed motor
- Synchronous motor — the valve head motor is a small 230 V synchronous motor; it is the most common part to fail and is usually replaceable without draining the system on heads with a detachable motor
- Valve head replacement — most makes allow the head to be removed from the body with two screws without draining the system; the body only needs changing if the spindle is seized or the paddle is leaking by
- Pump overrun — some boilers need a permanent live and neutral to run the pump after the burner shuts down; wire it from the boiler's pump terminals, not from the valve switches
- Isolation — heating controls must have a means of isolation (a switched fused connection unit with a 3 A fuse is standard) and the whole control circuit is normally fed from that single 3 A FCU
- Electrical work — rewiring heating controls on an existing circuit is a Minor Electrical Installation Works Certificate job; the boiler itself must only be worked on by a Gas Safe registered engineer where gas is involved
- BS 7671:2018+A4:2026 — all the control wiring must comply; use heat-resistant flex or cable where it runs near the boiler flue or cylinder (Regulation 522.2)
- Colour conventions are not universal — Drayton, Danfoss, Tower, Sunvic and others broadly follow Honeywell colours on replacement heads but some older valves (Sunvic in particular) use different colours and some 2-port heads have 4 wires (no separate end switch common); always read the diagram in the head
Quick Reference Table
Quoting a heating job? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Feature | S-Plan | Y-Plan |
|---|---|---|
| Valves | Two or more 2-port spring-return valves | One 3-port mid-position valve |
| Boiler and pump call | Valve end switches in parallel | Single micro-switch in the valve head |
| Hot water and heating together | Yes, both valves open | Yes, mid-position |
| Heating only | Heating valve open, cylinder valve closed | Valve driven to port B |
| Hot water only | Cylinder valve open, heating valve closed | Rest position, port A |
| Extra zones | Add a 2-port valve per zone | Not practical; convert to S-Plan |
| Meets Approved Document L 2021 zoning for larger dwellings | Yes with three valves | No |
| Valve wires | 5 per valve (brown, blue, grey, orange, earth) | 5 (grey, white, orange, blue, earth) |
| Typical valve cost 2026 | £55–£110 each (22 mm) | £70–£130 |
| Head-only replacement | Usually yes | Usually yes |
| Most common fault | Motor failure; end switch not making | Motor failure; valve stuck mid-position; micro-switch failure |
| Classic symptom of failure | One zone never gets hot; boiler never fires on that zone | Radiators warm when only hot water is on; boiler won't fire until lever is moved |
Detailed Guidance
How S-Plan works
Each zone has its own demand chain: programmer channel → thermostat → brown (motor live) on that zone's 2-port valve. When the thermostat calls, the motor drives the valve open against its spring. As it reaches fully open, the end switch inside the head closes between grey and orange. Grey is fed with a live (on the standard diagram, from the permanent live via the programmer's "on" output, so the switch only passes a live when the zone is on), and orange goes to the common boiler/pump live. Both valves' orange wires join at the wiring centre, so either zone calling fires the boiler and pump.
When the thermostat is satisfied, the motor loses power and the spring returns the valve to closed, opening the end switch. If no other zone is calling, the boiler and pump stop. That is the interlock: no open valve, no burner.
The wiring centre is usually a 10- or 12-way junction box near the cylinder. The standard S-Plan wiring centre connections are:
| Terminal | Function | Connected to |
|---|---|---|
| L | Permanent live (from 3 A FCU) | Programmer L, valves' grey (via diagram), boiler L where required |
| N | Neutral | Programmer N, valves' blue, boiler N, pump N |
| E | Earth | All earths |
| HW demand | Programmer HW ON → cylinder stat common; cylinder stat call → cylinder valve brown | Cylinder stat, cylinder valve brown |
| CH demand | Programmer CH ON → room stat; room stat call → heating valve brown | Room stat, heating valve brown |
| Boiler/pump | Both valves' orange | Boiler switched live, pump live |
How Y-Plan works
The 3-port valve has one inlet (AB) and two outlets (A to the cylinder, B to the heating). With no power it rests with A open (hot water). The logic is driven by two inputs:
- White receives a live when the heating is calling (programmer CH ON through the room thermostat)
- Grey receives a live when hot water is not required: either the programmer's HW OFF terminal or the cylinder thermostat's "satisfied" contact
The valve head then works out the position:
Grey (HW off/satisfied) White (CH demand) Valve position Orange (boiler/pump)
─────────────────────────────────────────────────────────────────────────────────────
OFF OFF A — HW only Live only if cyl stat calling*
OFF ON Mid — both Live
ON ON B — CH only Live
ON OFF Holds last pos. Off (phantom ~100 V possible)
*The cylinder stat "call" contact feeds the boiler/pump live directly on the standard diagram
The standard Y-Plan wiring centre connections (Honeywell numbering, which most makes copy):
| Terminal | Function |
|---|---|
| 1 | Cylinder stat satisfied → valve grey |
| 2 | Neutral: programmer N, valve blue, boiler N, pump N |
| 3 | Room stat demand → valve white |
| 4 | Earth |
| 5 | Programmer HW ON → cylinder stat common |
| 6 | Cylinder stat call → boiler/pump live (joined with valve orange) |
| 7 | Programmer CH ON → room stat common |
| 8 | Boiler switched live (from valve orange and terminal 6) |
| 9 | Permanent live: FCU → programmer L |
| 10 | Pump live |
The thing to grasp is that in Y-Plan the hot water call fires the boiler directly through the cylinder stat, while the heating call fires it through the valve's micro-switch once the valve has moved. That is why a dead valve motor kills the heating but leaves the hot water working, and why a cylinder stat that never satisfies leaves the valve parked on A with the radiators cold.
Fault-finding decision tree
START: heating or hot water not behaving
│
├─ Identify the plan: two or more 2-port valves = S-Plan;
│ one 3-port valve on the common flow = Y-Plan
│
├─ Is there 230 V at the wiring centre L and N? → no = FCU fuse, programmer supply
│
├─ S-PLAN
│ ├─ One zone cold, the other fine?
│ │ ├─ Thermostat calling? (230 V on that valve's brown) → no = stat/programmer
│ │ ├─ Valve moves when brown is live (lever travels, head hums)? → no = motor
│ │ ├─ Valve open but no live on orange? → end switch failed: new head
│ │ └─ Orange live but boiler silent? → boiler or pump, not the controls
│ ├─ Both zones cold, boiler never fires?
│ │ └─ Check boiler switched live from orange junction; then boiler
│ ├─ Radiators warm when only HW on (or cylinder heats on CH only)?
│ │ └─ 2-port valve passing: spindle not seating, paddle worn → new body
│ └─ Lever will not move?
│ └─ Seized spindle → body replacement (drain or freeze)
│
└─ Y-PLAN
├─ Hot water fine, no heating?
│ ├─ 230 V on white when room stat calls? → no = stat/programmer
│ ├─ Valve moves to mid/B when white live? → no = motor
│ └─ Valve moves but no live on orange? → micro-switch: new head
├─ Heating fine, no hot water?
│ ├─ Cylinder stat calling (230 V on terminal 6)? → no = cyl stat/programmer
│ ├─ Valve returning to A when heating off? → no = valve stuck on B
│ └─ Cylinder stat satisfied too early? → stat setting or position
├─ Radiators warm when HW only selected?
│ └─ Valve not returning fully to A (weak spring, worn paddle) → head, then body
├─ Boiler only fires when the manual lever is moved?
│ └─ Micro-switch not making in mid-position → new head
└─ Valve "buzzing" continuously?
└─ Motor stalled against a seized spindle → body, or motor if spindle free
Testing a valve head safely
Isolate at the FCU and prove dead before removing any cover; the wiring centre carries 230 V and the valve heads have exposed terminals under the cover. For live testing, use a voltage indicator to GS38 at the wiring centre terminals, not at the valve, and keep the valve head cover on.
A 2-port motor can be checked with the system isolated by measuring resistance across brown and blue: a synchronous motor typically reads a few kilohms; open circuit is a dead motor. The end switch is checked between grey and orange with the lever held in the manual open position: it should read closed. On a 3-port head, grey to blue and white to blue test the two motor windings (the V4073 head uses a single motor with a resistor-and-diode logic circuit, so readings vary; compare against a known-good head of the same make rather than against a fixed figure). The micro-switch is checked between the switch common and orange with the valve driven to mid-position.
Most heads from the main manufacturers detach from the body with two screws and a tab. Pull the head, check the spindle turns freely with pliers (a quarter turn against spring pressure on a 2-port), and if it does, a new head fixes the fault without draining. If the spindle is seized or the valve passes, the body must come out, which means draining the system down to that level or freezing the pipe either side.
Converting Y-Plan to S-Plan
The usual trigger is a boiler replacement or an extension that needs a third zone. The conversion is: remove the 3-port valve, fit a tee, fit a 2-port valve on each outlet (and any new zone), fit a new wiring centre, and rewire. The programmer and thermostats can usually be kept, although the HW OFF terminal is no longer used. Allow half a day to a day with the system drained, and quote the valves, wiring centre, fittings, inhibitor and a Minor Electrical Installation Works Certificate. In 2026 the labour and materials for a straightforward two-valve conversion typically come to £350–£600; a third zone adds £150–£250 plus the pipework.
What the Building Regulations ask for
For a boiler replacement in England, Approved Document L 2021 and the Domestic Building Services Compliance Guide 2021 require time and temperature control of both space heating and hot water, a boiler interlock, and TRVs on radiators in rooms without the room thermostat. Dwellings over 150 m² need at least two space-heating zones with independent time and temperature control. Both S-Plan and Y-Plan satisfy the interlock requirement when wired correctly; only S-Plan satisfies the multi-zone requirement without a second 3-port valve. The 2018 "Boiler Plus" requirements for combination boilers (weather compensation, load compensation, smart control or flue gas heat recovery) do not apply to regular and system boilers, but a time and temperature control and interlock do.
The boiler replacement is notifiable to Building Control, normally through the Gas Safe register's notification route for gas boilers or OFTEC for oil, and the controls are checked as part of that commissioning.
Frequently Asked Questions
Which should I fit on a new system, S-Plan or Y-Plan?
S-Plan. It costs slightly more (two valves instead of one) but gives a reliable interlock on every zone, is simple to fault-find, and can be extended to three or more zones to meet Approved Document L for larger dwellings. Y-Plan is only worth keeping where it is already installed and working.
My Y-Plan radiators get warm when only hot water is selected. Is the boiler faulty?
Almost certainly not. The 3-port valve is not returning fully to port A, so some flow goes to the heating. It is usually a tired spring or a worn paddle in the valve; a new head fixes the spring, a new body fixes the paddle. Gravity circulation through a poorly designed flow pipe can produce the same symptom on older systems and is cured with a non-return valve.
Can I use a 4-wire 2-port valve in an S-Plan system?
Yes, with care. Some 2-port heads have no separate grey wire; the end switch common is linked internally to the brown motor live. It works in a standard S-Plan but it means the end switch passes the zone demand live rather than a permanent live, which is fine for the boiler call but matters if the diagram relies on a permanent live through the switch. Read the head's diagram and wire accordingly.
Does rewiring the heating controls need an electrician?
The work must comply with BS 7671:2018+A4:2026 and should be certified with a Minor Electrical Installation Works Certificate. A heating engineer with the competence to inspect and test can do and certify it; it is not notifiable under Part P as it is an alteration to an existing circuit. Gas work on the boiler itself needs a Gas Safe registered engineer.
How do I identify the plan when the wiring centre has been bodged?
Count the valves on the pipework first; the wiring follows the plumbing. Two or more 2-port valves is S-Plan however the box is wired. One 3-port valve with three ports is Y-Plan (mid-position) or W-Plan (diverter): a mid-position valve has a manual lever and the letters A, B, AB on the body; a diverter has no mid-position and usually no lever.
Regulations & Standards
Building Regulations 2010, Approved Document L, Volume 1: Dwellings, 2021 edition (England) — heating system controls, boiler interlock, zoning for dwellings over 150 m²
Domestic Building Services Compliance Guide 2021 — minimum control requirements for boiler replacements
Building Regulations (Amendment) 2018 ("Boiler Plus") — combination boiler control requirements
BS 7671:2018+A4:2026 — Requirements for Electrical Installations: Regulation 522.2 (ambient temperature), Chapter 53 (switching and isolation), Part 6 (certification)
Gas Safety (Installation and Use) Regulations 1998 — competence for gas work
BS EN IEC 60730-2-9:2019+A2:2020 — Automatic electrical controls: particular requirements for temperature sensing controls (thermostats)
BS EN 12828:2012+A1:2014 — heating systems in buildings: design for water-based heating systems
BS 7593:2019 — code of practice for the preparation, commissioning and maintenance of domestic central heating and cooling water systems (inhibitor on refill)
HSE GS38 — electrical test equipment for use on low-voltage electrical systems
GOV.UK — Approved Document L: Conservation of fuel and power, Volume 1 Dwellings
HSE — GS38 Electrical test equipment for use on low voltage systems
zone valves and wiring — motorised valve types and wiring in detail
heating controls — thermostats, programmers and what Part L requires
heating controls upgrade — upgrading controls at boiler replacement
boiler programmer not working — when the programmer rather than the valve is the fault
cylinder selection — cylinder thermostats and coil connections
fused connection units fused spurs explained — the 3 A FCU that feeds the controls