Summary
Ladders are not banned. That myth has done real harm, because it leads some tradespeople to believe the rules do not really apply to them. The law is that a ladder is acceptable for the right job, done the right way, with a ladder in the right condition. Falls from ladders remain one of the biggest causes of serious injury and death in construction and maintenance, and most of them come from short jobs done in a hurry: cleaning a gutter, fixing a satellite dish, changing a light fitting.
The questions are always the same. Is a ladder the right tool for this task, or would a tower, podium or MEWP be safer? Is the ladder suitable and in good condition? Is it set up properly? Is the person using it trained and able to keep three points of contact?
This guide covers when a ladder is justified, how to set one up, the pre-use and detailed inspection regime, what changed with BS EN 131, and how to record it all so you can show an inspector or client that you manage ladder risk properly.
Key Facts
- Work at Height Regulations 2005 — require work at height to be avoided where possible, then prevented from causing falls, then the consequences of a fall minimised.
- Regulation 7 and Schedule 6 — a ladder can be used only if the risk assessment justifies it because of low risk and short duration, or site features that cannot be changed.
- Short duration — HSE guidance indicates around 30 minutes in one position as a guide, but the risk assessment decides.
- Light loads — up to 10 kg carried up a leaning ladder, per HSE INDG455.
- Angle — leaning ladders at 75°, the "1 in 4" rule: 1 unit out at the base for every 4 units up.
- Extension above landing — at least 1 m (about three rungs) above the landing point when used for access.
- Top rungs — do not work from the top three rungs of a leaning ladder; on stepladders, do not stand on the top three steps (including the platform) unless there is a suitable handhold.
- Three points of contact — two feet and a hand while climbing; when working, keep a hand free or the body supported.
- Overreaching — keep your belt buckle (navel) within the stiles.
- Stepladders — use them facing the work, not side-on, unless the task needs it and a risk assessment supports it.
- BS EN 131 — the European standard for ladders; since 2018 the "Professional" and "Non-professional" classes replaced the older UK Class 1, EN 131 and Class 3 categories.
- Maximum load — BS EN 131 ladders are tested for a maximum user load of 150 kg, including tools and materials.
- Wider base — under BS EN 131-1, leaning ladders over 3 m long must have a wider base, typically a stabiliser bar.
- Inspection — pre-use check by the user each day, and detailed visual inspections at intervals set by the employer, recorded.
- Electrical work — use non-conductive ladders (glass fibre stiles) near live electrical equipment.
Quick Reference Table
Spending too long on quotes? squote turns a 2-minute voice recording into a professional quote.
Try squote free →| Check | Pre-use (user, every day) | Detailed inspection (competent person, periodic, recorded) |
|---|---|---|
| Stiles | Not bent, split or damaged | Close inspection along whole length |
| Feet | Present, not worn or missing, clean | Replace if worn |
| Rungs or treads | Not bent, loose or missing; clean | Rivets and welds secure |
| Locking bars (stepladders) | Not bent, engaging fully | Hinges and rivets secure |
| Platform | Not split or buckled | Fixings checked |
| Labels | Readable, class and load visible | Replace missing labels |
| Stabiliser bar | Fitted and secure (over 3 m) | Fixings tight |
| Extension latches and guides | Engage fully, free moving | Wear checked |
| Glass fibre stiles | No cracks, blooming or exposed fibres | Assess conductivity risk |
| Overall | Clean, no paint, oil or mud | Taken out of use and labelled if defective |
Detailed Guidance
Is a ladder justified?
Work through the hierarchy in the Work at Height Regulations 2005:
- Avoid — can it be done from the ground (extending poles, ground-level assembly)?
- Prevent — if not, use equipment that prevents falls: a mobile tower, podium step, scaffold or MEWP.
- Minimise — only where those are not reasonably practicable, use a ladder, with measures to reduce the risk and consequences.
A ladder is generally reasonable for:
- Access to and from another level, such as a scaffold lift or loft.
- Short tasks, around 30 minutes in one position, with light tools and materials.
- Tasks where you can keep three points of contact, or at least a handhold, on a leaning ladder.
A ladder is usually not suitable for:
- Long tasks such as fascia replacement, gutter replacement along a whole elevation or painting a gable.
- Work needing both hands with force applied sideways, such as drilling masonry overhead.
- Carrying heavy or bulky items above 10 kg.
- Work in strong winds, on slippery or uneven ground, or near overhead power lines.
Setting up a leaning ladder
- Ground — firm, level and clean. Use a levelling device rather than bricks or blocks.
- Angle — 1 in 4. Many ladders have an angle indicator on the stile.
- Top support — rest on a solid surface, not on plastic guttering or glass; use a standoff if needed.
- Securing — tie the ladder at the top or bottom, use a stability device, or, as a last resort, have someone foot it.
- Landing — extend at least 1 m above the landing point when used for access.
- Overlap — on extension ladders, maintain the manufacturer's minimum rung overlap.
- Location — keep clear of doors and vehicle routes, or protect the base with barriers.
Setting up a stepladder
- Open fully with locking bars engaged.
- Place all four feet on firm, level ground.
- Face the work rather than working side-on, wherever possible.
- Do not stand on the top three steps (including the platform) unless there is a suitable handhold.
- Avoid side loads such as heavy drilling to one side.
The inspection regime
Pre-use check. The user checks the ladder at the start of each working day and after anything happens to it, such as being dropped or moved from a dirty area. It takes less than a minute and need not be recorded, though many firms use a tick sheet.
Detailed visual inspection. A competent person carries out a more thorough inspection at regular intervals, set by the employer based on use and conditions. Many firms inspect monthly or quarterly. Record it, and many firms tag each ladder with the date. Regulation 12 of the Work at Height Regulations 2005 requires inspection of work equipment where its safety depends on installation conditions or where it is exposed to conditions causing deterioration.
Taking a ladder out of use. Any defect means the ladder is removed from use, labelled "Do not use" and repaired by the manufacturer or destroyed. Do not bodge repairs.
BS EN 131 ladder classes
| Class | Old equivalent | Use |
|---|---|---|
| Professional | Class 1 / EN 131 (trade) | All trade and commercial use |
| Non-professional | EN 131 (light) / Class 3 | Domestic use only |
Both classes have a 150 kg maximum load. The Professional class is tested to more cycles and higher durability. Trade businesses should buy Professional class ladders and stepladders.
BS EN 131 partly superseded the ladder parts of BS 2037:1994 and BS 1129:1990. Older ladders made to those standards (Class 1) may still be safe if in good condition, but should be phased out as they fall due for replacement.
Training and competence
Anyone using a ladder at work should know how to choose, check and set it up. That can be on-the-job training, a toolbox talk or a short course. The Ladder Association offers recognised training. Record who has been trained. See working at height and toolbox talks.
Frequently Asked Questions
Are ladders banned on building sites?
No. HSE states clearly that ladders can be a sensible and practical option for low-risk, short-duration work. Some principal contractors restrict them on their sites through site rules, which is their right, but that is a contractual rule, not the law.
How long can I work from a ladder?
HSE guidance gives about 30 minutes in one position as a guide for leaning ladders. The real test is the risk assessment: a short but awkward task can still be unsuitable for a ladder.
Do I need to record ladder inspections?
Detailed visual inspections should be recorded. Daily pre-use checks need not be, though a simple sheet is good evidence of a safe system. Keep records for each ladder, ideally tagged with a unique number.
Can I use a domestic ladder for trade work?
You should not. Non-professional ladders are tested to lower durability levels. Buy Professional class ladders to BS EN 131 for trade use.
What is the 1 in 4 rule?
For every 4 units of height up the wall, the base should be 1 unit out. For example, a ladder reaching 4 m up the wall should have its feet 1 m from the wall. This gives an angle of about 75°.
Regulations & Standards
Work at Height Regulations 2005 (SI 2005/735) — Regulation 6 (avoidance of risks), Regulation 7 (selection of equipment), Regulation 12 (inspection) and Schedule 6 (ladders).
Health and Safety at Work etc. Act 1974 — general duties of employers and the self-employed.
Provision and Use of Work Equipment Regulations 1998 — ladders are work equipment that must be suitable and maintained.
BS EN 131-1:2015 (as amended) — ladders, terms, types and functional sizes.
BS EN 131-2:2010 (current amendment A3:2025) — ladders, requirements, testing and marking, including the Professional and Non-professional classes.
HSE INDG455 — Safe use of ladders and stepladders: a brief guide.
Construction (Design and Management) Regulations 2015 — planning and managing work at height on construction sites.
HSE — Safe use of ladders and stepladders (INDG455) — HSE's brief guide
HSE — Work at height — the hierarchy and duties
legislation.gov.uk — Work at Height Regulations 2005 — statutory text
The Ladder Association — standards, training and guidance on BS EN 131
working at height — the full working-at-height framework
working at height regulations — the regulations in detail
loft hatch and ladder installation — fixed loft ladders for homeowners
scaffold inspection records — inspection records for scaffolds and towers
risk assessment method statement rams — recording the ladder risk assessment