Summary
Beko is one of the biggest-selling washing machine brands in the UK by volume, and its machines are built on the Arçelik platform that also appears under the Blomberg, Grundig, Leisure and some Flavel badges. That matters to a repairer for two reasons: the same fault logic and the same parts (door interlocks, drain pumps, inlet valves, heaters, NTC thermistors) appear across badges, and the error-code list on one Beko model is a reasonable starting point for its sister brands — but only a starting point.
The complication is that Beko has used at least two numbering schemes over the last fifteen years. Older display models report a short list of E-codes (typically E01 to E08) and most sources agree that E01 is the door lock. On newer machines the list runs to E18 and some of the numbers have moved: a code that meant "water not filling" on one platform is listed as "heater" or "overfill" on another by different repair guides. Several widely circulated online lists are copied from each other and from dishwasher code tables, which is why they disagree. The honest position is that the code families below are reliable, the individual numbers are model-specific, and the user manual (or a sticker inside the door or on the back panel on some ranges) is the authority.
For a tradesperson the practical value is the same as with any brand: the code narrows the search before a panel comes off. The great majority of E-codes on site turn out to be a blocked filter, a kinked hose, a closed stop tap, an obstructed door seal or too much detergent, not a dead component. Treat the code as a symptom the control board has detected, work the cheap checks first, and only then move to component testing with a multimeter.
Key Facts
- Display models show a two-to-three-character code (E01, E02 … E18) on the digital display; non-display models flash a combination of programme-stage LEDs (wash, rinse, spin, end) that has to be decoded from the user manual for that model
- E-codes are consumer-level; a separate H-code series (H1 upwards) appears only in the engineer diagnostic test mode and points at specific components — these are not shown during normal use
- E01 — door lock on most Beko platforms: the control board has not seen the door interlock confirm "closed and locked"; the usual causes are a door not pushed fully home, laundry trapped in the seal, or a failed interlock (a thermally operated PTC interlock that has aged)
- Water-fill family (commonly listed as E02 or E04 depending on platform): expected water level not reached in the time limit — stop tap closed, inlet hose kinked, inlet mesh filter blocked by limescale or debris, low mains pressure, or a failed inlet solenoid valve
- Drain family (commonly listed as E03 or E05 depending on platform): water not pumped out in the time limit — blocked pump filter (coins, hair grips, bra wires), kinked or siphoning drain hose, blocked standpipe, or a failed drain pump
- Heater and thermistor family (variously E02, E05, E06, E07 or E08 in different lists): no temperature rise detected, heater open circuit, NTC out of range, or heater relay stuck — limescale on the element is the single biggest real-world cause in hard-water areas
- Motor family (commonly E06 on newer lists): tachometer or motor circuit fault — worn carbon brushes on brushed motors, a loose tacho coil, or a triac fault on the main PCB
- Pressure sensor / overfill: level sensor (pressure switch or analogue sensor) out of range or water above the overflow level — a blocked pressure hose or a leaking inlet valve that keeps filling
- Mains supply family (E18 and similar on newer lists): mains voltage outside the working range — check the socket, the plug fuse and the RCD before touching the machine
- Excess foam (E17 on some lists, shown as "SUd" style symbols on others): overdosing or hand-wash detergent, not a fault
- Nominal current — a 2.2 kW heater plus motor draws close to 10 A on a 230 V supply, so the 13 A plug fuse to BS 1362 is normal; a blown plug fuse usually indicates a heater or suppressor fault, not a "bad fuse"
- RCD protection — socket-outlets up to 32 A in a domestic installation require 30 mA RCD protection under BS 7671:2018+A4:2026 Regulation 411.3.3; a heater with insulation breakdown trips the RCD rather than showing a code
- Door interlock — Beko uses a PTC thermal interlock on most models; it takes a few seconds to release at the end of a cycle, which customers often report as "door stuck"
- Hard water — much of the South East, East Anglia and the Midlands has water above 200 mg/l calcium carbonate, which scales heaters and thermistors and is the main reason heater-family codes arrive after 4–7 years
- WEEE Regulations 2013 — a dead machine is large household WEEE; a retailer supplying a replacement must offer like-for-like take-back and household waste recycling centres must accept it free
- Consumer Rights Act 2015 — goods must be of satisfactory quality and durable; a heater or PCB failure within the first couple of years may support a claim against the retailer independent of Beko's warranty
- Manufacturer warranty — Beko offers a standard guarantee on registration (commonly 2 years at the time of writing, with longer cover on selected models); check the registration before quoting a chargeable repair that may be covered
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Fault family | Codes commonly listed (verify against the model manual) | What the board has detected | First checks on site | Typical outcome |
|---|---|---|---|---|
| Door / interlock | E01 (most lists) | Door not confirmed locked, or lock not releasing | Door shut firmly, seal clear, interlock continuity | Interlock replacement if no continuity |
| Water fill | E02 or E04 (lists disagree) | Level not reached in time | Stop tap, inlet hose kink, inlet mesh filter, mains pressure | Clean filter; inlet valve if coil open circuit |
| Drain | E03 or E05 (lists disagree) | Water not emptied in time | Pump filter, drain hose, standpipe, pump impeller | Clear filter; pump if winding open or impeller jammed |
| Heater / NTC | E02, E05, E06, E07 or E08 (lists disagree) | No temperature rise or sensor out of range | Heater resistance (around 20–30 Ω cold for a 2 kW element), NTC resistance at room temperature | Heater or NTC replacement; descale |
| Motor / tacho | E06 (newer lists) | Motor not turning as commanded | Brushes, tacho coil, drive belt, wiring to motor | Brushes or motor; PCB if triac shorted |
| Pressure sensor / overfill | E07, E04 or E11 (lists disagree) | Level sensor out of range or overfill | Pressure hose blocked or split, air chamber blocked, inlet valve passing | Clear chamber; sensor or valve |
| Mains supply | E18 (newer lists) | Voltage out of range | Socket, plug fuse, extension leads, RCD | Supply fault, not the machine |
| Excess foam | E17 (newer lists) | Suds suppressing drain or level sensing | Detergent type and dose | Rinse out and advise customer |
| Leak detection | E13 (some lists) | Water in the base tray | Hoses, door seal, tub-to-pump hose | Locate and repair the leak |
| Communication / PCB | E09, E10 (some lists) | Board-to-board or sensor comms fault | Connectors, water ingress on the display board | Module replacement |
Where the numbers in this table are given as alternatives, it is because published code lists for different Beko platforms genuinely disagree. Do not order a part on the strength of a number from a generic list.
Detailed Guidance
Fault-finding decision tree
START: Beko machine stops and shows an E-code (or flashing LEDs)
│
├─ STEP 1: Note the exact code, the model number (on the door frame
│ or rear plate) and where in the cycle it stopped
│
├─ STEP 2: Confirm the code meaning in THAT model's manual
│ (do not trust a generic list — numbering differs by platform)
│
├─ STEP 3: Rule out the supply
│ ├─ Socket live? Plug fuse (13 A BS 1362) intact? RCD tripped?
│ └─ On an extension lead or multi-way adaptor? → remove it
│
├─ DOOR FAMILY
│ ├─ Door fully closed, nothing trapped in the seal?
│ ├─ Wait 2–3 minutes after the cycle for the PTC interlock to release
│ ├─ Continuity across interlock terminals when latched? → no = replace
│ └─ Interlock fine → wiring to the PCB, then PCB
│
├─ FILL FAMILY
│ ├─ Stop tap fully open? Hose kinked behind the machine?
│ ├─ Inlet mesh filter (at the hose-to-valve joint) scaled? → clean
│ ├─ Flow at the tap good? (low pressure at peak times triggers it)
│ └─ Inlet valve coil open circuit (typically 2–5 kΩ good)? → replace
│
├─ DRAIN FAMILY
│ ├─ Pump filter (behind the kick panel) blocked? → clear
│ ├─ Drain hose kinked, pushed too far into the standpipe, or
│ │ siphoning? → correct the run (standpipe top 600–800 mm high)
│ ├─ Pump impeller turns freely? Winding open circuit? → replace pump
│ └─ Pump runs but no flow → tub-to-pump hose obstruction
│
├─ HEATER / NTC FAMILY
│ ├─ Heater resistance cold: open circuit or very high → replace
│ ├─ Insulation to earth low (<2 MΩ) → replace (will also trip RCDs)
│ ├─ NTC resistance plausible at room temperature? → no = replace
│ └─ Both good → heater relay on the main PCB
│
├─ MOTOR FAMILY
│ ├─ Belt on? Drum turns by hand?
│ ├─ Brushes worn below ~10 mm (brushed motors)? → replace
│ ├─ Tacho coil secure and reading a few hundred ohms? → no = replace
│ └─ All good → motor control (triac) on PCB
│
└─ PRESSURE / OVERFILL FAMILY
├─ Pressure hose split or blocked? Air chamber scaled? → clear
├─ Machine filling when switched off? → inlet valve passing
└─ Sensor output out of range → replace sensor
Reading the code correctly
Beko display models show the code in place of the time-remaining figure, usually with a steady or flashing "E" prefix. Some older models show only the number, and some models with a reduced display show the fault as a letter-and-symbol combination (a tap symbol for fill problems, a padlock for the door). Non-display models flash programme-stage LEDs in a sequence that is unique to the model's manual. Photograph the panel before you clear the fault; customers frequently misremember the code by the time you arrive.
Beko machines generally hold the last fault in memory until a cycle completes normally. Pulling the plug for a minute clears the display on most models but not the stored fault, which is useful: the diagnostic mode (entered on most platforms with a button-and-dial combination described in the service documentation, not the user manual) will read it back.
The door interlock
Beko uses a PTC thermal interlock on most domestic models. When the cycle starts, a heating element in the interlock expands a bimetallic strip that closes the lock contacts and the mains contact for the rest of the machine. If the contacts have burnt or the PTC has failed, the board never sees "locked" and raises the door code even though the door is physically shut. The symptoms are the same as a door that is not fully closed, so clear the seal and shut the door firmly before you test anything.
Test with the machine isolated: unplug it, remove the door switch (two screws through the door frame on most models) and check for continuity between the common and lock terminals with the latch pushed in. No continuity equals a failed interlock. A new interlock is a 15–20 minute job and one of the cheapest fixes on any washing machine.
Water-fill codes: it is almost never the valve
On a fill code, work from the wall inwards. A closed or half-open stop tap after building work, a hose crushed when the machine was pushed back, and a blocked inlet mesh filter account for the majority of fill faults. Hard-water limescale and grit from mains work both block the small mesh filter at the hose-to-machine connection; pull it out with pliers and clean it.
Only when the supply, hose and filter are proven good should you test the inlet solenoid. Most double inlet valves read a few kilohms across each coil; open circuit is a dead coil. A valve that fills slowly despite good pressure usually has a scaled flow restrictor rather than a dead coil, and on a cheap valve replacement is quicker than cleaning.
Drain codes: the filter and the hose
The drain pump filter sits behind the kick panel at the bottom right of most Beko models. It collects coins, hair grips, bra wires and socks, and a blocked filter is the single most common service call on any washing machine. Bail out the water into a tray before you unscrew it, and check the impeller turns freely once the filter is out.
If the filter is clear, look at the drain hose. A hose pushed too far down a standpipe will siphon, a hose that is kinked behind the machine will not drain, and a standpipe with a blocked trap will back up. The hose should enter a standpipe with an air gap and the top of the standpipe should be about 600–800 mm above floor level, which is the height the pump is designed to lift to. A drain code that only appears at the end of the rinse but not after the wash points to a partial blockage.
A pump that hums but does not pump has a jammed or stripped impeller. A pump that is silent and reads open circuit across its winding is dead. Both are a straightforward swap, and on Beko models the pump is usually a separate unit from the filter housing so you do not need to drop the whole sump.
Heater and thermistor codes
The heater family is where repair economics bite. The heating element lives in the bottom of the outer tub, held by a single nut that expands a rubber gasket. In hard-water areas the element scales up, its resistance drifts, and eventually the insulation breaks down to earth. Before you even get a heater code, the machine often trips the RCD mid-cycle or blows the plug fuse at the point the heater switches on, which is a strong clue.
Test with the machine unplugged: a healthy 1.9–2.2 kW element reads roughly 20–30 Ω cold, and anything reading megohms or open circuit is finished. Then test insulation resistance from either terminal to the earth tag; below about 2 MΩ it will trip a 30 mA RCD under load and needs replacing. The NTC thermistor is usually mounted in the heater's rubber seal and is tested separately: resistance should be in the kilohm range at room temperature and should fall steadily as you warm it in your hand.
A heater and NTC that both test good with a persistent heater code is a heater relay on the main board, and that is a PCB-replacement decision that depends on the age and value of the machine.
Motor and tacho codes
Beko has used both brushed universal motors and brushless (inverter) motors depending on the model tier. Brushed motors wear out their carbon brushes; when they get below about 10 mm the motor arcs, loses torque and eventually stops turning, and the board raises a motor code because the tachometer sees no rotation. Brushes are a 30-minute job. The tacho coil on the end of the motor can also work loose or go open circuit, which gives the same code with a motor that is otherwise healthy.
On inverter models the motor is driven by a separate control board, and a motor code is more often a connector or a board than the motor itself. Check every plug on the motor loom before you condemn anything.
Pricing a Beko repair honestly
A diagnostic visit in 2026 is typically £60–£110 depending on area, usually deducted from the repair if the job goes ahead. Common repairs land in these bands including the visit:
| Repair | Typical 2026 price fitted |
|---|---|
| Clear pump filter or inlet filter, reset | £60–£110 |
| Door interlock | £85–£140 |
| Drain pump | £110–£170 |
| Inlet valve | £100–£160 |
| Heater and NTC | £120–£190 |
| Carbon brushes | £100–£150 |
| Main PCB | £180–£300 |
| Drum bearings (seal and bearings, if serviceable) | £180–£300 |
Where a machine is more than seven or eight years old and the fault is a PCB or bearings, a replacement is usually the better advice; say so, and record that you did.
Frequently Asked Questions
Why do different websites give different meanings for the same Beko code?
Because Beko has used more than one numbering scheme as its platforms have changed, and because many online lists are copied from each other or confused with Beko dishwasher codes. E01 as a door-lock fault is consistent across most sources; the water, drain and heater numbers are not. The only authority for a given machine is its own manual or service sheet.
The display is blank and the machine is dead — is that an error code?
No. A dead machine with no display is a supply or interlock problem rather than a stored code. Check the socket with a known-good appliance, the plug fuse, and whether the RCD or an RCBO has tripped. A tripped 30 mA RCD at the point the heater switches on is a strong indicator of a heater insulation fault.
Can I clear the code by turning the machine off and on?
Pulling the plug for a couple of minutes clears the display and lets the cycle restart on most Beko models, which is worth doing once to confirm the fault repeats. It does not fix anything, and the stored fault remains readable in the diagnostic mode.
Is a washing machine repair notifiable electrical work?
No. Repairing or replacing a plug-in appliance is not work on the fixed electrical installation and is outside Approved Document P. Installing a new socket-outlet or a dedicated circuit for a machine in a kitchen is work on the installation and must comply with BS 7671:2018+A4:2026; a new circuit is notifiable under Part P in England and Wales.
What should I tell the customer about Beko's warranty?
Check whether the machine was registered and when it was bought. Beko's standard guarantee runs from the purchase date on registration, and selected ranges carry longer cover on specific components. A chargeable repair on a machine still under manufacturer warranty is poor advice; refer them to Beko's service line first.
Regulations & Standards
BS 7671:2018+A4:2026 — Requirements for Electrical Installations (IET Wiring Regulations): Regulation 411.3.3 (30 mA RCD protection for socket-outlets), Chapter 64 (inspection and testing)
Building Regulations 2010, Approved Document P (Electrical safety — dwellings) — fixed installation work; appliance repair is outside scope
BS 1362:1973 — Specification for general purpose fuse links for domestic and similar purposes (plug fuses)
BS 1363-1:2023 — 13 A plugs, socket-outlets, adaptors and connection units: Part 1, rewirable and non-rewirable 13 A fused plugs
Electrical Equipment (Safety) Regulations 2016 — product safety for appliances placed on the UK market
Waste Electrical and Electronic Equipment Regulations 2013 (WEEE) — end-of-life appliance take-back
Consumer Rights Act 2015 — satisfactory quality and durability of goods
Water Supply (Water Fittings) Regulations 1999 — inlet hoses and connections to the mains supply must be of an approved type
GOV.UK — Waste Electrical and Electronic Equipment (WEEE) regulations
washing machine error codes samsung — the same fault-family approach for Samsung's alphanumeric codes
washing machine error codes bosch — Bosch E-code list and diagnostics
washing machine error codes hotpoint — Hotpoint and Indesit F-codes
washing machine leaking — locating a leak once a leak-detection code appears
washing machine not spinning — unbalance, motor and brush faults in depth
safe isolation procedure — isolating safely before any live testing