Summary
"The shower keeps tripping the electrics" is one of the commonest electrical call-outs in domestic work and one of the most frequently misdiagnosed by whoever got there first, usually the customer or a plumber who has swapped the shower unit without testing anything. The diagnosis starts with a question most customers can answer: which thing trips? The small switch with a test button (the RCD, or an RCBO for the shower circuit alone) trips on earth leakage. The plain switch marked with the circuit's rating (the MCB) trips on overcurrent. They point to different faults, with different tests, and the fix for one does nothing for the other.
RCD tripping on a shower circuit is almost always the heating element. An electric shower heats water instantaneously with an element of 7–10.5 kW inside a plastic or copper can; over the years scale builds on the element sheath, the sheath cracks or pits, water reaches the resistance wire, and current leaks to the earthed water and the can. The leakage is small at first (a few milliamps, enough to trip a sensitive RCD intermittently or when combined with other circuits' leakage) and grows until the RCD trips the moment the shower is turned on. An insulation resistance test between the live conductors and earth at the shower terminals confirms it in a minute. Water elsewhere (a terminal block flooded by a leaking inlet, a joint in the loft under a dripping tank, a cable chased into a wet wall) is the next suspect, followed by cable damage and, where the shower shares an RCD with half the house, cumulative leakage.
MCB tripping is a current problem: the shower draws more than the breaker allows, because the shower was upgraded to a higher rating without upgrading the circuit, because a terminal has worked loose and is arcing, because the pull-cord isolator has burnt out, or because there is a short. Here the test is a check of the ratings, a visual inspection of every termination, and a measurement of the running current.
This guide gives the diagnostic order, the tests and the readings that matter, the circuit ratings for each shower size, the regulations that apply to bathroom circuits and to RCD selection, what can be repaired and what cannot, and what to charge. For a shower that does nothing at all see electric shower not working; for a general RCD-tripping diagnosis see rcd tripping; for the cable and breaker sizing see shower circuit cable size calculator.
Key Facts
- RCD trips = earth leakage — current flowing from live or neutral to earth; a 30 mA RCD must trip between 15 mA and 30 mA (BS EN 61008 / BS EN 61009), and must trip within 300 ms at rated residual current (40 ms at 5× for additional protection testing)
- MCB trips = overcurrent — overload (shower rating exceeds breaker) or short circuit (fault current far above rating, instantaneous trip)
- Element failure — the cause in roughly 80–90% of RCD-tripping showers over three years old; symptoms start as intermittent tripping when the shower is first switched on or at full heat, progressing to immediate tripping
- Insulation resistance — test at 500 V DC between live conductors (L and N together) and earth with the shower connected and the isolator on: BS 7671 Table 64 minimum is 1 MΩ for a 230 V circuit; a healthy shower reads above 2 MΩ (often tens of MΩ), a failing element reads below 1 MΩ and a wet one below 0.1 MΩ. Disconnect the shower and re-test to separate the appliance from the cable
- Water ingress — into the terminal block from a leaking inlet elbow, a weeping solenoid or a split hose; into a loft junction box from condensation or a dripping tank; into a cable chased in a wall that is damp; all produce leakage that comes and goes with the wet
- Cable damage — a nail or screw into the cable (picture hooks, a new towel rail, a shelf) creating a track to earth or a part short; rodent damage in the loft; a chafed cable at a joist edge
- Cumulative leakage — every appliance leaks a little (filters, elements, electronics); on a split-load board with one 30 mA RCD covering the shower, the kitchen and the sockets, standing leakage of 10–15 mA plus a shower's 10 mA leakage trips the RCD only when the shower runs. Regulation 531.3.2 requires the designer to limit standing leakage so that unwanted tripping does not occur; the usual fix is an RCBO for the shower circuit
- RCD type — showers are resistive loads, so a Type AC or Type A RCD is suitable; Type A is now the default for new work. A faulty RCD (tripping below 15 mA or at random) is tested with an RCD tester and replaced if out of tolerance
- Shower ratings and circuits — 7.5 kW: 32.6 A (32 A / 6 mm²); 8.5 kW: 37 A (40 A / 6 mm² short runs, 10 mm² long); 9.5 kW: 41.3 A (45 A / 10 mm²); 10.5 kW: 45.7 A (45–50 A / 10 mm²); 10.8 kW: 47 A (50 A / 10 mm²); all at 230 V, subject to cable length, installation method and grouping (BS 7671 Appendix 4)
- Isolator — a 45 A or 50 A double-pole pull-cord switch outside zones 0–2 (or a wall switch outside the bathroom); a burnt or arcing isolator causes MCB trips, a hot smell and a shower that cuts in and out
- Terminations — the shower's terminal block, the isolator and the breaker: loose or undersized terminations overheat under 40–50 A and cause nuisance MCB trips, burnt insulation and eventually a fault to earth
- Additional protection — BS 7671 Regulation 701.411.3.3 requires 30 mA RCD protection for all circuits of a location containing a bath or shower, and Regulation 411.3.3 for socket outlets up to 32 A and cables concealed in walls; an RCD must not be removed or bypassed to stop tripping
- Notifiable work — replacing a shower like for like on an existing circuit is not notifiable under Approved Document P (England); a new circuit or a consumer unit change is; work in the bathroom zones is a special location and the installer must be competent to test and certify
- Safe isolation — isolate at the isolator and the breaker, lock off, prove dead with an approved voltage indicator and a proving unit (GS38) before opening the shower; the terminal block is live when the isolator is on even if the shower is off
- Pricing (2026) — fault-finding visit with insulation resistance and RCD tests £80–£140; element replacement where available £120–£220; like-for-like shower replacement £200–£400 fitted plus the unit (£120–£350); RCBO for the shower circuit £90–£160; isolator replacement £70–£120; cable re-run or repair £150–£400 plus making good; new 10 mm² circuit for a higher-rated shower £350–£650
Quick Reference Table
Diagnosed the problem? Create a repair quote in minutes with squote.
Try squote free →| Symptom | Trips which device | Most likely cause | Test | Fix |
|---|---|---|---|---|
| Trips the moment the shower is switched on, every time | RCD / RCBO | Element insulation failed; or flooded terminal block | IR test L+N to E at shower: < 1 MΩ; look for water | Replace element or shower; dry and fix leak |
| Trips after a few minutes, or only at full heat | RCD / RCBO | Element insulation breaking down as it heats | IR test warm vs cold; trips reproducible at high setting | Replace element or shower |
| Trips intermittently, more in winter or damp weather | RCD / RCBO | Water in loft joint or wall chase; element early failure | IR test cable with shower disconnected; inspect joints | Dry and remake joint; re-route cable; replace shower if element |
| Trips only when another appliance is also running | Shared RCD | Cumulative leakage on one RCD | Measure standing leakage with an earth leakage clamp; isolate circuits | RCBO for shower circuit; find the other leaky appliance |
| Trips when the pull cord is pulled, shower off | RCD / RCBO | Fault on the circuit cable or isolator, not the shower | IR test from isolator with shower disconnected | Cable repair or re-run; replace isolator |
| Trips after a new shower of higher rating was fitted | MCB | Overload: shower rating exceeds breaker and possibly cable | Compare kW rating to breaker and cable size | New circuit at correct rating; or shower of original rating |
| Trips after 5–15 minutes, breaker hot, burning smell | MCB | Loose or undersized termination; overloaded breaker | Inspect terminations; thermal camera or touch test (dead) | Remake terminations; replace damaged devices and cable ends |
| Trips instantly with a bang, shower off | MCB | Short circuit: failed element shorting, water across terminals, cable damage | Continuity L–N dead test; inspect | Replace shower or repair cable |
| Shower works but RCD test button does nothing | — | RCD faulty | RCD tester | Replace RCD |
| RCD trips at random with nothing switched on | RCD | Faulty RCD, or a neutral-to-earth fault on any circuit | RCD tester; IR test each circuit N–E | Replace RCD; find the N–E fault |
| Trips after the bathroom was retiled or a towel rail fitted | RCD or MCB | Fixing through the cable in a wall | IR and continuity tests; locate with a cable tracer | Repair or re-route cable |
Detailed Guidance
Step 1 — which device, and when
Establish three things before any test: whether it is the RCD (or the shower's RCBO) or the MCB that trips; whether it trips immediately, after a delay, or intermittently; and what has changed (new shower, new tiles, a towel rail, a loft conversion, a leak). Then:
What trips?
├─ RCD / RCBO (earth leakage)
│ ├─ Immediately, every time ──────► Element failed or terminal block wet
│ ├─ After minutes / at full heat ─► Element breaking down when hot
│ ├─ Intermittent, weather-related ► Water in a joint or chase; early element failure
│ ├─ Only with other loads on ─────► Cumulative leakage on shared RCD
│ └─ With shower disconnected ─────► Cable or isolator fault
└─ MCB (overcurrent)
├─ After a new, bigger shower ───► Overload: circuit undersized
├─ After 5–15 min, hot, smell ───► Loose termination / burnt isolator
└─ Instantly, bang ──────────────► Short circuit: element, water, cable
Step 2 — isolate and inspect
Isolate at the pull-cord and at the breaker, lock off, and prove dead with a GS38 voltage indicator and proving unit. Open the shower unit. Look for water: a damp or stained terminal block, mineral deposits, green corrosion on the terminals, a wet floor to the casing, a weeping inlet elbow or solenoid, a cracked heater can. Water in the terminal block is often from a hairline leak at the inlet connection that only drips when the shower is running, which is exactly when the RCD trips. Look at the terminations: any discolouration or melted insulation at the shower, the isolator or the breaker points to a loose connection carrying 40–50 A.
Step 3 — insulation resistance test
With the circuit isolated and the shower connected, link L and N at the shower terminals (or test each to earth in turn) and test to earth at 500 V DC. BS 7671 Table 64 sets 1 MΩ as the minimum for a 230 V circuit; treat anything under 2 MΩ on a shower as suspect, because the leakage rises when the element is hot and wet. Then disconnect the shower at its terminal block and test the circuit cable alone from the isolator or the board: a high reading on the cable and a low reading with the shower connected means the shower; a low reading on the cable alone means the cable, a joint or the isolator. If the shower reads low, test the element on its own (disconnect the element leads from the control board on units where that is possible): a reading below 1 MΩ, and especially below 0.5 MΩ, confirms the element.
A useful refinement for intermittent faults: run the shower until it trips, isolate immediately, and test while the element is still hot. Many elements read 5 MΩ cold and 0.3 MΩ hot.
Step 4 — element, or new shower
Some manufacturers supply heater cans as spares and the swap is a 30–60 minute job: drain, remove the can, fit the new one with new seals, refill and test for leaks before re-energising. Many budget and some premium units do not have a replaceable element, or the spare costs most of a new shower; then the shower is replaced like for like (same kW rating, same inlet and cable position where possible). A like-for-like replacement on the existing circuit is not notifiable, but it is work in a special location (zone 1 or 2) and must be followed by tests (continuity of the cpc, insulation resistance, polarity, earth fault loop impedance, RCD operation) and a Minor Electrical Installation Works Certificate. Do not fit a higher-rated shower than the circuit was designed for; see Step 7.
Step 5 — cable, joints and isolator
If the cable reads low with the shower disconnected, find the fault. Trace the route: a loft junction box under a tank or near a leaking roof, a chase in a wall that has been drilled for a towel rail, mirror or shelf, a cable run through a wet wall or a cold loft where condensation drips. Open and inspect every accessible joint. A cable tracer or a time-domain reflectometer locates a nail through a buried cable; otherwise test from each end to narrow the position. Repair by replacing the damaged length with a proper enclosed joint in an accessible position, or re-run the cable; a maintenance-free junction box buried in a wall is acceptable only if it is rated for it (BS 7671 Regulation 526.3). Isolators that have arced, discoloured or lost their spring action are replaced with a 45 A or 50 A double-pole unit of the right rating for the shower, outside zones 0–2 if in the bathroom.
Step 6 — cumulative leakage and the RCD itself
If the shower tests healthy (above 2 MΩ hot and cold), the cable is clean, and the RCD trips only when the shower runs alongside other loads, measure the standing earth leakage on the RCD's load side with an earth leakage clamp meter. Modern homes with induction hobs, heat pumps, EV chargers, PCs and LED drivers can carry 10–15 mA of permanent leakage; BS 7671 Regulation 531.3.2 requires the installation to be arranged so that the accumulation of protective conductor currents does not cause unwanted tripping, and the IET guidance is to keep standing leakage well below the RCD's rated residual current (a third is a common design limit). The fix is to move the shower (and any other high-leakage circuit) onto its own RCBO, which also means a shower fault no longer takes out the fridge. Test the RCD with an RCD tester at ½×, 1× and 5× rated residual current: trip at ½× or a random trip time means a faulty RCD; replace it.
Step 7 — MCB trips: ratings and terminations
Compare the shower's rated power with the breaker and the cable. The current at 230 V is kW × 1000 ÷ 230: 8.5 kW is 37 A, 9.5 kW is 41.3 A, 10.5 kW is 45.7 A, 10.8 kW is 47 A. A B40 breaker will carry 45.7 A for a long time but will eventually trip on thermal overload, typically after several minutes at full heat, which is exactly the "it trips halfway through a shower" complaint after a bigger unit has been fitted. The cable must be rated for the breaker: 6 mm² twin and earth clipped direct is good for about 47 A, but only about 32–34 A if run in insulation, so 10 mm² is the norm for 9.5 kW and above and for any run in a loft through insulation; check the actual installation method, length and voltage drop against BS 7671 Appendix 4 (see shower circuit cable size calculator). The right fix for an undersized circuit is a new circuit at the correct rating (10 mm² and a 45–50 A RCBO, £350–£650 plus making good), or a shower of the original rating. Never fit a bigger breaker to an existing cable to stop it tripping.
Where the ratings are correct, MCB tripping after a period of running comes from heat at a bad connection: a loose terminal at the shower, the isolator or the breaker, or a breaker that has itself degraded after years of heavy cycling. Remake every termination to the manufacturer's torque, cut back heat-damaged conductor, replace any discoloured device, and measure the running current with a clamp meter to confirm it matches the rating.
What not to do
Do not remove, bypass or "upgrade" the RCD to a higher rated residual current to stop tripping: 30 mA additional protection is mandatory in a bathroom and the tripping is the RCD doing its job on a shower that is leaking current into the water. Do not fit a 50 A breaker on a 6 mm² cable. Do not refit a shower whose terminal block has been wet without finding the leak. Do not reset and retest repeatedly with the customer in the shower. Do not leave without a test sheet: the Minor Works Certificate protects the customer and you.
Frequently Asked Questions
The RCD trips the moment I turn the shower on. Is it the shower or the wiring?
Almost always the shower, specifically the heating element, if the shower is more than a few years old; an insulation resistance test at the shower terminals settles it in a minute (below 1 MΩ to earth with the shower connected, healthy with it disconnected, means the shower). If the circuit reads low with the shower disconnected, the fault is in the cable, a joint or the isolator, often caused by water in a loft or a fixing through the wall.
Can the element be replaced, or does the whole shower need changing?
Some manufacturers sell the heater can as a spare and it is a straightforward swap; many do not, or the part costs almost as much as a new unit. If the shower is over eight to ten years old or has other wear (a stiff temperature control, a tired solenoid, scale in the outlet), replace it. Fit the same kW rating unless the circuit is upgraded, test the circuit afterwards, and issue a Minor Works Certificate.
Why does the shower only trip when the washing machine or kettle is on?
Because the shower shares a 30 mA RCD with other circuits and the total leakage of everything on that RCD exceeds its trip point only when the shower adds its share. Each appliance may be within limits; together they are not. Measure the standing leakage, find any appliance that leaks more than it should, and put the shower on its own RCBO so it is not affected by, and does not affect, the rest of the house.
We fitted a 10.5 kW shower to replace an 8.5 kW one and now the MCB trips after a few minutes. Why?
A 10.5 kW shower draws about 45.7 A; the 8.5 kW circuit was designed for 37 A, probably with a 40 A breaker and possibly 6 mm² cable. The breaker is doing its job on a sustained overload. The fix is a new circuit in 10 mm² with a 45 A or 50 A RCBO, sized for the route and length, or going back to an 8.5 kW shower. Fitting a bigger breaker to the existing cable is a fire risk and a breach of BS 7671. See electric shower installation.
Is replacing an electric shower notifiable under Part P?
Like-for-like replacement on the existing circuit is not notifiable in England under Approved Document P, but it is work in a special location and must be tested and certified on a Minor Electrical Installation Works Certificate by someone competent to do so. A new circuit, a circuit upgrade or a consumer unit change is notifiable, through a competent person scheme or Building Control. If the existing circuit has no RCD protection, adding it is required before the shower is put back into service.
Regulations & Standards
BS 7671:2018+A2:2022 — Requirements for Electrical Installations: Regulation 411.3.3 (additional protection by 30 mA RCD), Section 701 (locations containing a bath or shower, including 701.411.3.3 RCD protection for all circuits, 701.512.3 accessory positions and zones), Regulation 531.3.2 (avoidance of unwanted RCD tripping from accumulated leakage), Chapter 52 and Appendix 4 (cable current-carrying capacity and installation methods), Regulation 526.3 (accessibility of joints), Part 6 and Table 64 (insulation resistance minimum 1 MΩ)
BS EN 61008-1 and BS EN 61009-1 — RCCBs and RCBOs for household use: rated residual current, trip time requirements
BS EN 60898-1 — circuit breakers for overcurrent protection for household installations (MCB characteristics)
BS EN 60335-2-35 — safety of household electrical appliances: particular requirements for instantaneous water heaters (electric showers)
BS EN 60529 — degrees of protection provided by enclosures (IP ratings for shower units and accessories in zones)
Building Regulations 2010, Schedule 1 Part P and Approved Document P — electrical safety in dwellings; notifiable work and special locations
Electricity at Work Regulations 1989 — safe isolation and working dead
HSE Guidance Note GS38 — electrical test equipment for use on low-voltage systems (voltage indicators and proving units)
IET Guidance Note 3: Inspection and Testing — test procedures and the Minor Electrical Installation Works Certificate
IET Guidance Note 7: Special Locations — bathroom zones and requirements
BS 7671 IET Wiring Regulations — IET — the current edition and amendments
Approved Document P: Electrical safety — GOV.UK — notifiable work and special locations
Electrical Safety First: RCDs explained — how RCDs work and why they trip
HSE GS38: Electrical test equipment for use on low voltage electrical systems — safe isolation and proving dead
Triton Showers: Technical support and troubleshooting — manufacturer fault guidance and element availability
Mira Showers: Electric shower support — manufacturer installation and fault guidance
electric shower not working — when the shower does nothing rather than tripping
rcd tripping — general RCD tripping diagnosis across circuits
rcbo tripping — RCBO-specific tripping faults
shower circuit cable size calculator — cable and breaker sizing by shower rating and route
electric shower installation — installing or upgrading a shower circuit correctly
rcd types explained — Type AC, A, F and B RCDs and when each applies
rcd vs rcbo — why a dedicated RCBO solves shared-RCD nuisance tripping
bathroom zones and ip ratings — zones 0–2 and where the isolator may go
shower pull cord switch fault — the isolator as the fault